Instrukcja obsługi La Crosse Technology WT-3122B
La Crosse Technology
zegar
WT-3122B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla La Crosse Technology WT-3122B (4 stron) w kategorii zegar. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
www.lacrossetechnology.com/support Page | 1
Instruction Manual
DC: 050614
Atomic Analog Wall Clock
Get Started
Step 1: Slide the switch to select a time zone.
Step 2: Insert 1 fresh AA, LR6 1.5 volt ALKALINE battery according to the
polarity marked on the case.
Step 3: Position the clock on an exterior wall that faces Ft. Collins Colorado.
During the night, your clock will automatically set itself.
Note: The hands will move to the 12:00 position and search for the radio signal.
If the radio signal is not received in the first 10 minutes, the clock will start
running from the 12:00 position and will continue to run. Do not attempt to
reset the hands manually even though the time on the clock is incorrect. The
clock is synchronizing to the WWVB signal and once the radio signal is decoded,
the hands will automatically adjust to the correct time. This may take up to 5
nights.
Position Clock
Choose a location 6 feet or more from electronics such as cordless phones,
wireless gaming systems, televisions, microwaves, routers, baby monitors,
etc., which can prevent signal reception.
Position clock near an exterior wall that faces Ft. Collins Colorado for
WWVB time signal reception.
The antenna is available for signal reception when the front or back of the
clock faces Colorado.
Reset:
If the clock does not respond to the various function modes, reset the clock by
pressing the RESET button on the movement case.
Note: We recommend that you change the battery every 24 months to maintain
accuracy. Remove the battery when the clock will not be in use for an extended
period.
www.lacrossetechnology.com/support Page | 2
Manual Set Time
On rare occasions in certain areas, the clock
may not be able to receive the radio
controlled function because of the strength of
the signal or the geographic location. In this
case, the clock can be set manually and
used as a regular quartz wall clock.
Note: Allow up to five nights for the clock to receive the WWVB signal before
manually setting the time.
Set the clock manually:
1. Press and hold the SET button for 3+ seconds to activate the manual mode.
Once the clock is in manual mode, there are two ways to move the minute
hand forward.
2. Hold the SET button down to move the minute hand forward consistently.
3. Alternatively, press the SET button rapidly (more than once per second) to
move the minute hand forward step by step (in minute increments).
4. Use these features to move the minute hand forward until the correct time is
set. The clock will automatically leave manual mode after the SET button is
not pressed for 6+ seconds.
Troubleshooting
The wonderful advantage of owning a radio controlled clock is that it is virtually -
trouble free. If the clock receives a clear time signal, it will set itself perfectly. If it
does not receive a time signal, consider the following:
Battery – The clock must have a fresh battery to receive and process the
time signal.
Location – Try a different location, ideally near a window. Your clock should
be at least six feet from computers, TVs, air conditioners, other radio-
controlled clocks and other electrical appliances that cause interference.
Weather – Electrical storms between you and Colorado during the night will
interfere with the WWVB signal.
Daylight Saving Time
The National Institute of Standards and Technology and WWVB encode a special
DST “bit” in the WWVB transmission for DST. Your clock will read this information
and automatically advance the hands one hour in the spring and eleven hours in
the fall.
Arizona
If you live in an area that does not recognize DST, you must slide the DST switch
OFF. To reactivate the DST program simply slide the switch to the ON position.
www.lacrossetechnology.com/support Page | 3
Manual WWVB Time Signal Search
For information about WWVB, visit: www.nist.gov/pml/div688/grp40/wwvb.cfm
Manual Signal Search:
The WWVB signal is strongest at night.
Hold the WAVE button down for 3+ seconds.
The hands will automatically reset to the 12:00 position, and the movement
will search for the WWVB time signal from Fort Collins, CO.
If the movement successfully receives the signal, the clock will reset
automatically to the correct time. The signal search takes approximately 3-8
minutes.
-Set the clock manually and the movement's micro, CPU will control the time
keeping function.
Internal Synchronization:
Once the clock has set correctly by the radio signal, the clock’s CPU operates
continuously. To ensure accuracy, the clock synchronizes the position of the
second and minute hands to the time calculated by the CPU every day. Second
hand synchronization occurs at 1:30 a.m. and 9:30 a.m. and minute hand
synchronization occurs between 1:50 and 2:01 am every day.
Signal Interference:
In some cases, the signal is affected by weather conditions and electrical
interferences, or the location of the clock itself may result in poor reception. If the
clock has not synchronized to the correct time within a few days of activation, you
may need to move the clock to a different location.
Frequently Asked Questions
Q. How long will the battery last?
A. A good AA alkaline battery will last over 24 months.
Q: Can I wire a control timing circuit to the La Crosse Technology® atomic clock?
A: No, the clock cannot work on a timing circuit. Opening the clock voids the warranty.
Q: Is there a booster antenna to receive the WWVB signal in a difficult location?
A: No, the clock cannot work with a booster antenna. Opening the clock or movement voids
the warranty.
Q: Can I shut off the WWVB signal?
A: No. If you manually set the time, when the clock receives a WWVB signal, that signal
will override the manual set. The WAVE button will temporarily stop a WWVB search, but
will not permanent stop the clock from receiving a WWVB time signal.
Q: Is there a version of analog clock with more than the four continental US times
zones?
A: La Crosse Technology® does not make an analog clock with more than four time zones.
These time zones are P (Pacific Time), M (Mountain Time), C (Central Time), and E
(Eastern Time).
Specyfikacje produktu
| Marka: | La Crosse Technology |
| Kategoria: | zegar |
| Model: | WT-3122B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z La Crosse Technology WT-3122B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje zegar La Crosse Technology
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
Instrukcje zegar
- zegar Ikea
- zegar Braun
- zegar Lenovo
- zegar Livoo
- zegar Geemarc
- zegar Panasonic
- zegar Muse
- zegar Nedis
- zegar Marquant
- zegar Casio
- zegar Citizen
- zegar ECG
- zegar Krontaler
- zegar TFA
- zegar Auriol
- zegar Techno Line
- zegar Seiko
- zegar Velleman
- zegar ART
- zegar Lorus
- zegar Invicta
- zegar Tronic
- zegar Oregon Scientific
- zegar Elro
- zegar Hama
- zegar Taylor
- zegar Hager
- zegar RCA
- zegar Trevi
- zegar Eurochron
- zegar Alecto
- zegar Zenith
- zegar ADE
- zegar Vitek
- zegar Profile
- zegar Fysic
- zegar Amplicom
- zegar Accusplit
- zegar Ascot
- zegar Ecom
- zegar United Office
- zegar Karlsson
- zegar Cresta
- zegar GlobalTronics
- zegar Jacob Jensen
- zegar Dugena
- zegar AcuRite
- zegar Fisher Price
- zegar Technoline
- zegar Audiovox
- zegar Davis
- zegar Balance Time
- zegar Valcom
- zegar Chacon
- zegar Zuiver
- zegar Irox
- zegar Konig
- zegar Glunz
- zegar Dexford
- zegar Ranex
- zegar Mondaine
- zegar IHome
- zegar BBrain
- zegar La Crosse
- zegar Sempre
- zegar Digi-tech
- zegar Global Tronics
- zegar ASA
- zegar TFA Dostmann
- zegar Lydion
- zegar Kogan
- zegar Antelope Audio
- zegar Equity
- zegar Mebus
- zegar Hermle
- zegar DB Technologies
- zegar Focus Electrics
- zegar Pyramid
- zegar Gingko
- zegar Weinberger
- zegar CyberData Systems
- zegar Electronics International
- zegar Antelope
Najnowsze instrukcje dla zegar
11 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024