Instrukcja obsługi La Crosse Technology WS-7159U

La Crosse Technology Stacja pogodowa WS-7159U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla La Crosse Technology WS-7159U (19 stron) w kategorii Stacja pogodowa. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/19

WS-7159U

Wireless 433 MHz

Radio-controlled Weather Station

Instruction Manual

Contents

Language Page

English 2

French 24

Spanish 46

FCC ID : OMO-01RX (Receiver), OMO-01TX (transmitter)

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

GB P.4 GB

P.5

GB P.2 GB

P.3

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 4

Quick Set-Up Guide 4

Detailed Set-Up Guide

Battery installation 5

Program Mode

Program Sequence and Default Settings 6

Function Keys 7

Setting the LCD Contrast 7

Setting the Time Zone 7

Daylight Saving Time Setting 8

Radio-controlled Time Setting 8

12/24-hour Time Setting 9

Setting the Time 9

Setting the Year, Day and Month 10

Setting the Snooze 10

Setting the Temperature Format 11

Setting the Forecast Sensitivity 11

Features

Weather Forecast Icons and Tendency Arrows 12

Indoor Temperature, Humidity, & Comfort Level Indicator 13

Outdoor Temperatures 14

Minimum & Maximum Records (Indoor, Outdoor, & Resetting) 14

Additional Remote Control Sending Units (Set-Up, Viewing & Operation)

Mounting 16

Troubleshooting 18

Maintenance & Care 19

Specifications 20

Warranty Information 21

TABLE OF CONTENTS INVENTORY OF CONTENTS

1. The indoor weather station (Figure 1).

2. One remote temperature sensor with mounting bracket

(Figure 2).

3. Three each, 1/2" Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1. Three fresh AA 1.5V batteries for the indoor weather station.

2. Two fresh AA 1.5V batteries for the remote temperature sensor.

3. One, Philips screwdriver for mounting.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology-Time and

Frequency Division) WWVB radio station is located in Ft. Collins, Colorado,

and transmits the exact time and date signal continuously throughout the

United States at 60 kHz. The signal can be received up to 2,000 miles away

through the internal antenna in the Weather Station. However, due to the

nature of the Earth’s Ionosphere, reception is very limited during daylight

hours. The weather station will search for a signal every night when reception

is best. The WWVB radio station derives its signal from the NIST Atomic

clock in Boulder, Colorado. A team of atomic physicists is continually

measuring every second, of every day, to an accuracy of ten billionths of a

second per day. These physicists have created an international standard,

measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom in

a vacuum. For more information on the atomic clock and WWVB please

see the NIST website at http://www.boulder.nist.gov/timefreq/stations/wwvb.

htm.

QUICK SET-UP GUIDE

Hint :

Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor weather station and remote temperature sensor 3 to 5

feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into

the indoor weather station.

(All outdoor remotes must be started before the indoor station)

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the indoor weather station and remote temperature sensor will

start to talk to each other and the display will show the indoor temperature,

humidity and an outdoor temperature. If the indoor weather station does

not display all information after the 15 minutes please retry the set up as

stated above. After all information has been displayed for 15 minutes you

can place your sensor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded area.

The remote temperature sensor has a range of 330 feet. Any walls that the

signal will have to pass through will reduce distance. An outdoor wall or

window can have up to 30 feet of resistance and an interior wall can have

Time LCD

Date LCD

Forecast LCD

Indoor LCD

Outdoor LCD

Figure 1

Figure 2

TX6U remote

temperature

sensor

Mounting

Bracket

up to 20 feet of resistance. Your distance plus resistance should not exceed

330 ft. in a straight line.

Note :

Fog and mist will not harm your remote temperature sensor but

direct rain must be avoided.

Note :

The remote temperature sensor transmits a signal every minute.

After the batteries have been installed, the indoor weather station will search

for the signal for a duration of 15 minutes. If there is no temperature reading

in the OUTDOOR LCD after 15 minutes, make sure the units are within

range of each other, or repeat the battery installation procedure. If a button

is pressed before the indoor weather station receives the temperature signal,

you will need to follow the battery installation procedure again.

To complete the set up of your wireless weather station after the 15 minutes

have passed please follow the steps that follow in the Detailed Set-Up Guide.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket. The bracket snaps

on and o easily.

2. Remove the battery cover, by sliding the cover down.

3. Observing the correct polarity install 2 AA batteries.

The batteries will t tightly (to avoid

start-up problems make sure they do not spring free).

4. Replace the battery cover by sliding upwards. Be

sure battery cover is on securely.

B. INDOOR WEATHER STATION

1. Remove the battery cover. To do this, insert a

solid object in the space provided at the lower-

central position of the battery cover, then push

up and pull out on the battery cover.

2. Observe the correct polarity, and install 3 AA

batteries.

3. Replace the battery cover.

Battery

Cover

Battery

Cover

Note :

Immediately after the batteries have been installed, the LCD

(Liquid Crystal Display) will flash, and a tone will sound. Within a

few seconds the indoor temperature, indoor relative humidity, and

the weather icons (sun and clouds) will be displayed. If not, remove

batteries for 10 seconds and reinstall. If the outdoor temperature is

not displayed within four minutes, remove batteries from both units,

wait 10 seconds, and reinstall making sure to install batteries into

the remote temperature sensor first. The time will show -:— and

start searching for the signal. If it successfully receives the time

signal (usually at night), it will display the correct time (default time-

zone is Eastern). You will need to adjust the time zone to match

your local time.

PROGRAM MODE

Programming Note :

If 30 seconds is allowed to pass, or the CH

button is pressed during the programming mode, the unit will confirm/

set the last information entered-the display will stop flashing and

return to normal time-date readings. If you don’t leave the program

mode during the programming of sections IV through XII, you can

advance to step 4 of the next program setting. If you do leave the

program setting (or want to program a specific setting) follow each

instructional step to program that setting.

I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS

The programming sequence and default (factory) settings are as

follows :

LCD Contrast 5

Time Zone -5 (Eastern)

Daylight Saving Time 1 (on)

Radio-controlled time reception ON

12/24-hour time 12

Time 12:00

Year 2003

Day and Month 1.1.

Snooze (this function not used) 10

Temperature Format ˚F

Forecast Sensitivity 2

Please note that while there is a snooze adjustment in the programming

this is an unused function as there is no alarm on the indoor weather station.

II. FUNCTION KEYS

The function keys are located on the front of the unit directly below the

LCD.

III. SETTING THE LCD CONTRAST

1. Press and hold the SET button for 5

seconds.

2. “LCD” will show in the time LCD and the

number setting will ash.

Note :

There are 8 LCD contrast levels to choose from-”Lcd 0" is the lightest,

and “Lcd 7” is the darkest.

3. Press and release the IN button to select the level you desire.

4. Press and release the SET button to confirm and advance to the Time

Zone setting.

IV. TIME ZONE SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the

number setting will ash.

3. Press and release the SET button again.

4. The time zone will flash in the date LCD.

5. Press and release the IN button to select your time zone.

Note :

When a time zone for the U.S. is selected the corresponding

abbreviation will appear above the time (please see the table on the next

page). It is possible to select any time zone from -12 GMT to +12 GMT (for

example to see the time in another country)

6. Press and release the SET button to confirm and advance to the Daylight

Saving Time setting.

V. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the

number setting will ash.

3. Press and release the SET button twice.

4. “DST” will appear in the date LCD and either

“1” or “0” will flash.

5. Press and release the IN button to select DST on or off.

“DST 0” indicates that the feature is off and the WWVB will not change

times automatically. “DST 1” indicates that the feature is on and the WWVB

will change times automatically.

Note :

Some locations (Arizona and parts of Indiana) do not follow Daylight

Saving Time, and should select “DST 0.”

6. Press and release the SET button to confirm and advance to the radio-

controlled time on/o setting.

VI. RADIO-CONTROLLED TIME ON/OFF SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number

setting will ash.

3. Press and release the SET button three times.

4. “RCC” will appear in the date LCD and “ON” or

“OFF” will ash in the time LCD.

TIME ZONES

GMT 0

Atlantic -4

EST; Eastern -5

CST; Central -6

MST; Mountain -7

PST; Pacific -8

ALA; Alaska -9

HAW; Hawaii -10

5. Press and release the IN button to select radio-controlled time on or off.

6. Press and release the SET button to confirm and advance to the 12/24-

hour time setting.

VII. 12 OR 24 HOUR TIME SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button four times.

4. “12h” or “24h” will flash in the time LCD.

5. Press and release the IN button to select 12

or 24-hour time format.

Note :

When in the 12-hour format “P.M.” will appear to the left of the hour

in the time LCD between the hours of noon and midnight.

6. Press and release the SET button to confirm and advance to the time

setting.

VIII. TIME SETTING

There are two methods by which the time and date can be set :

A) Automatically via WWVB reception, or

B) Manually.

A. WWVB (Remote Control Time)

This method requires you to do nothing, except wait for the signal to be

received, and to select a time zone. Reception usually takes approximately

10 minutes during optimal conditions. The best condition for reception is at

night, between midnight and 6:00 am-when there is less atmospheric

interference. To keep your time as accurate as possible, the indoor weather

station conducts a WWVB search every night between these hours, and

overrides any manually set time. The WWVB tower icon (appearing in the

TIME LCD) will flash when a signal-search is in progress and a signal is

being received, and will remain steady when the signal has been received.

If the WWVB time has not been received after 10 minutes of battery

installation, you may manually set the time or leave the time function alone

(reception will occur regardless).

GB P.8 GB

P.9

GB P.6 GB

P.7

Specyfikacje produktu

Marka:	La Crosse Technology
Kategoria:	Stacja pogodowa
Model:	WS-7159U

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z La Crosse Technology WS-7159U, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Stacja pogodowa La Crosse Technology

La Crosse Technology M71633 Instrukcja

8 Stycznia 2025

La Crosse Technology V41CA Instrukcja

8 Stycznia 2025

La Crosse Technology CA74177 Instrukcja

26 Grudnia 2024

La Crosse Technology S73071 Instrukcja

26 Grudnia 2024

La Crosse Technology 308-1415FCT-NH Instrukcja

26 Grudnia 2024

La Crosse Technology S77925v3 Instrukcja

8 Października 2024

La Crosse Technology V61 Instrukcja

8 Października 2024

La Crosse Technology V23 Instrukcja

2 Października 2024

La Crosse Technology 308-1414B Instrukcja

29 Września 2024

La Crosse Technology WS-7091 Instrukcja

29 Września 2024

Instrukcje Stacja pogodowa

Najnowsze instrukcje dla Stacja pogodowa

Ascot GT-WS-07s Instrukcja

15 Stycznia 2025

Ventus K0382 Instrukcja

14 Stycznia 2025

TFA 20.1082.17 Instrukcja

12 Stycznia 2025

Oregon Scientific BAR310HG Instrukcja

12 Stycznia 2025

Auriol AHFL 433 B2 Instrukcja

12 Stycznia 2025

Oregon Scientific BAR 898 Instrukcja

11 Stycznia 2025

Davis Weatherlink Touch Console Instrukcja

11 Stycznia 2025

Taylor 5156 Instrukcja

8 Stycznia 2025

Techno Line WS 9632 Instrukcja

4 Stycznia 2025

Oregon Scientific WMR180 Instrukcja

31 Grudnia 2025