Instrukcja obsługi La Crosse Technology KWS-8140-WH
La Crosse Technology
Klok
KWS-8140-WH
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla La Crosse Technology KWS-8140-WH (10 stron) w kategorii Klok. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/10
1
DIGITAL ATOMIC WALL CLOCK
Indoor Temperature/Humidity
Outdoor Temperature
Moon Phase
Model KWS- -8140U IT | Instruction Manual
The features radidigital atomic wall clock o-controlled time, date, alarm, indoor temperature and humidity, and moon
phase. Wireless outdoor temperature range (open air) up to 200 feet (60.96 meters).
Atomic Wall Clock
Outdoor Temperature Transmitter: TX40U- IT
2
Table of Contents
Atomic Wall Clock 1
Outdoor Temperature Transmitter: TX40U- 1 IT
Features 2
Setup Instructions Step-By-Step 3
915MHz Reception Outdoor Transmitter 3
WWVB Radio-controlled Time Signal 3
Function Buttons 3
Program Menu 4
Time Zone 4
Daylight Saving Time 4
Time Set 4
5 Calendar Set
5 12/24 Hour Format
5 Fahrenheit /Celsius
Exit Program Menu 5
Display Modes 5
Alarm Set 6
Deactivate Alarm 6
6 Snooze
Moon Phase 6
Low Battery 7
Install or Replace Batteries in the Outdoor Transmitter 7
Install or Replace Batteries in the Atomic Wall 7 Clock
Position the Atomic Wall 7 Clock
Position the Outd r Transmitteroo 8
Care and Maintenance 8
Specifications 8
Warranty Information 9
FCC Statement 10
KWS- - 8140U IT
2-AA Alkaline batteries
9.17“ x 1.16“ x 8.30“
(233 x 29.4 x 210.8 mm)
Features
• Wireless outdoor temperature (°F or °C)
• Monitors indoor temperature (°F or °C)
• Monitors indoor humidity
• 12 moon phases
• Atomic time and date with manual setting
• Automatically updates for Daylight Saving Time (on/off option)
• 12/24 hour time display
• Perpetual calendar
• Time zone setting
• Time alarm with snooze
• Time display: hours, minutes, seconds
• Wall hanging or free standing
TX40U- IT
2-AAA Alkaline batteries
1.27" x 0.55" x 3.40"
( 32.4mm x 14.1 x 86.5mm)
3
Setup Instructions Step- -StepBy
Step 1:
• Slide the battery cover down and lift off the back of the transmitter.
• Insert 2 NEW AAA batteries (not included) into the TX40U-IT transmitter. Observe the correct polarity.
Step 2:
• Remove battery cover from atomic wall clock: insert a solid object in the space provided at the lower central position of -
the battery cover, then push up and pull out on the battery cover.
• Insert 2 NEW AA batteries (not included) into the back of the atomic wall clock. Observe the correct polarity (see
marking inside the battery compartment). The atomic wall display time and indoor temperature.clock will
• Within 3 minutes the outdoor temperature should be displayed.
• Keep the atomic wall clock and transmitter within 10 feet of each other during setup (15 minutes).
• Do Not Mix Old and New Batteries
• Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries
915MHz Reception for Outdoor Transmitter
The atomic wall receive the temperature data within 4 seconds. If the temperature data is not being received 2 clock will
minutes after set up (or the display shows “ ”), then please check the following points:- - -
1. The distance of the atomic wall clock or outdoor temperature transmitter should be at least 6 feet (2 meters) away
from any interfering sources such as computer monitors or TV sets.
2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.
3. Using other electrical products such as headphones or speakers operating on the same signal frequency (915MHz)
may prevent correct signal transmission and reception.
4. Neighbors using electrical devices operating on the 915MHz signal frequency can also cause interference.
Note: When the 915 MHz signal is received correctly, do not re-open the battery cover of either the outdoor temperature
transmitter or atomic wall clock, as the batteries may spring free from the contacts and force a false reset. Should this
happen accidentally then reset all units (see above) otherwise transmission problems may occur.SETUP
The maximum transmission range is from the outdoor temperature transmitter to the atomic wall 220 feet (60 meters)
clock (in open space). However, this depends on the surrounding environment and interference levels. If no reception is
possible despite the observation of these factors, all system units have to be reset (see SETUP).
WWVB Radio-controlled Time Signal
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal continuously
throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal
antenna in the atomic wall clock. However, due to the nature of the Earth’s Ionosphere, reception is very limited
during daylight hours. The will search for a signal every night when reception is best. atomic wall clock
Once the outdoor temperature is displayed on the atomic wall clock, atomic wall clock will the WWVB tower icon in the
flash the top of the LCD. This indicates that the atomic wall clock has detected a radio signal and is trying to receive it.
When the time code is received, the WWVB tower becomes permanently lit and the time will be displayed.
If the tower icon flashes, but does not set the time or the WWVB tower does not appear at all, then please take note of the
following:
• Recommended distance to any interfering sources like computer monitors or TV sets is a minimum of 6 feet (2 meters).
• Within ferro-concrete rooms (basements, superstructures), the received signal is naturally weakened. In extreme cases,
please place the unit close to a window and/or point its front or back towards the Fort Collins, Colorado..
• During nighttime, the atmospheric disturbances are usually less severe and reception is possible in most cases. A single
daily reception is adequate to keep the accuracy deviation below 1 second.
Note: In case the atomic wall clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the
time can be manually set (please see Program Menu).
Function Buttons
The hasatomic wall clock four easy to use buttons: SET + ALM SNZ
Specyfikacje produktu
| Marka: | La Crosse Technology |
| Kategoria: | Klok |
| Model: | KWS-8140-WH |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z La Crosse Technology KWS-8140-WH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Klok La Crosse Technology
6 Września 2024
6 Września 2024
5 Września 2024
3 Września 2024
1 Września 2024
1 Września 2024
31 Sierpnia 2024
30 Sierpnia 2024
29 Sierpnia 2024
29 Sierpnia 2024
Instrukcje Klok
- Klok Braun
- Klok Lenovo
- Klok Livoo
- Klok Nedis
- Klok Casio
- Klok Citizen
- Klok ECG
- Klok Krontaler
- Klok TFA
- Klok Auriol
- Klok Techno Line
- Klok Velleman
- Klok ART
- Klok Oregon Scientific
- Klok Elro
- Klok Hama
- Klok Hager
- Klok Trevi
- Klok Alecto
- Klok Fysic
- Klok Ascot
- Klok Ecom
- Klok Karlsson
- Klok Cresta
- Klok GlobalTronics
- Klok AcuRite
- Klok Fisher Price
- Klok Technoline
- Klok Balance Time
- Klok Chacon
- Klok Irox
- Klok Konig
- Klok Glunz
- Klok BBrain
- Klok Sempre
- Klok ASA
- Klok TFA Dostmann
- Klok Kogan
- Klok Equity
- Klok Focus Electrics
Najnowsze instrukcje dla Klok
19 Września 2024
18 Września 2024
17 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
15 Września 2024
15 Września 2024
14 Września 2024