Instrukcja obsługi Konig SEC-ALARM200

Konig Dzwoni alarm SEC-ALARM200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Konig SEC-ALARM200 (72 stron) w kategorii Dzwoni alarm. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/72
2013-10-22
SEC-ALARM200
MANUAL (p. 2)
WIRELESS ALARM SYSTEM
ANLEITUNG (S. 6)
DRAHTLOSES ALARMSYSTEM
MODE D’EMPLOI (p. 10)
SYSTEME D'ALARME SANS FIL
GEBRUIKSAANWIJZING (p. 14)
DRAADLOOS ALARMSYSTEEM
MANUALE (p. 18)
SISTEMA D'ALLARME SENZA FILI
MANUAL DE USO (p. 22)
SISTEMA DE ALARMA INALÁMBRICA
MANUAL (p. 27)
SISTEMA DE ALARME SEM FIOS
HASZNÁLATI ÚTMUTATÓ (o. 31.)
VEZETÉK NÉLKÜLI RIASZTÓRENDSZER
KÄYTTÖOHJE (s. 35)
LANGATON HÄLYTYSJÄRJESTELMÄ
BRUKSANVISNING (s. 39)
TRÅDLÖST ALARMSYSTEM
NÁVOD K POUŽITÍ (s. 43)
BEZDRÁTOVÝ POPLAŠNÝ SYSTÉM
MANUAL DE UTILIZARE (p. 47)
SISTEM DE ALARMĂ WIRELESS
ΕΓΧΕΙΡΙΔΙΟ XPHΣ ΣH (σελ. 51)
ΑΣΥΡΜΑΤΟ ΣΥΣΤΗΜΑ ΣΥΝΑΓΕΡΜΟΥ
BRUGERVEJLEDNING (s. 55)
TRÅDLØST ALARMSYSTEM
VEILEDNING (s. 60)
TRÅDLØST ALARMSYSTEM
ИНСТРУКЦИЯ (стр. 64)
БЕСПРОВОДНАЯ СИСТЕМА
СИГНАЛИЗАЦИИ
KILAVUZ (s. 69)
KABLOSUZ ALARM Sİ İSTEM
2
ENGLISH
WIRELESS ALARM SYSTEM
QUICK SETUP GUIDE
Functions include:
Alert – Advises you to what is happening around the house.
Alarm – Protects your home / assets while you are away.
Communication – Calls you during an emergency, you can also call in to perform a variety of
operations.
This Quick Guide will show you how to setup the system and use basic functions. It is strongly
recommended that you refer to the User’s Instructions for full illustrations on how the system should be
installed and operated.
Installation of the Control Panel
1. Plug in the adapter to a wall socket
and the other end should be
connected to the socket on the
Control Panel marked “DC 12 V”. You
should hear 3 beeps.
2. Remove the screw on the battery
cover and insert 4 pcs of AAA
batteries into the battery holder.
Tighten the screw afterwards.
3. Plug in a phone line from the “LINE”
socket to the phone outlet on the
wall.
4. If you want to connect a telephone to
the Control Panel, the phone can be
plugged into the socket marked
“PHONE” on the Control Panel.
3
Installation of Sensors - Batteries
Insert batteries in all the
sensors and mount them
accordingly. Please refer to the
User’s Instructions for details
on how to install the Motion
Sensor and Door / Window
Sensor.
Remove the yellow
protective tag from
the sensors.
Insert 9V alkaline
battery in the sensor
Operation - Alert Mode
All the sensors are preprogrammed at the factory, so the
Control Panel can communicate with these sensors after the
batteries are installed properly.
Door/Window Sensor
Activate the Door / Window Sensor, you will hear continuous
beeping, one beep at a time, indicating zone 1 sensor is
activated. Activate the other Door / Window Sensor, you will
hear continuous beeping, two beeps at a time, indicating
zone 2 sensor is activated.
Notes: The door/Window Sensor is factory default in zone 1
and zone 2.
Activate the sensor
by opening the door,
you will hear voice
announcement and
continuous beeping.
Close the door, and
beeping stop.
Motion Sensor
To perform the walk test, its necessary to enable the Alert Zone (Bypass Zone) feature in the Control
Panel. After the walk test, it needs to disable this alert zone feature otherwise it will bypass the signal in
the alarm mode.
To enable the alert zone feature:
1. Press [PROG] + MPIN [factory default 1 2 3 4].
2. Press [8] to select Alert Zone.
3. Press [8] to enable for zone 3. The zone 3 LED will stay ON after selected.
4. Press [PROG] when finished.
Walk in front of the Motion Sensor, you will hear the continuous beeping from the Control Panel.
Beeping will continue for approx. 20 seconds for every motion detected.
To disable the alert zone feature:
1. Press [PROG] + MPIN [factory default 1 2 3 4].
2. Press [8] to select Alert Zone.
3. Press [3] to disable for zone 3. The zone 3 LED will flash after selected.
4. Press [PROG] when finished.
Notes:
1) The Motion Sensor is factory default in zone 3.
2) If the Motion Sensor doesn’t respond to your movement, try not to move in front of the sensor for
20 seconds (i.e. no motion is detected in 20 seconds), then walk again. The Motion Sensor is
designed to be triggered only if no motion is detected for 20 seconds.
Program Emergency Phone Number
During an emergency, the Control Panel can call up to 5 phone numbers to inform you about an
emergency situation. There are 5 phone memories, it will first call phone memory 1, then phone
memory 2, etc. It will call phone memory 5 last. Each phone number can have a redial count up to
Beep

Specyfikacje produktu

Marka: Konig
Kategoria: Dzwoni alarm
Model: SEC-ALARM200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Konig SEC-ALARM200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Dzwoni alarm Konig

Konig

Konig SEC-DUMMYFL20 Instrukcja

12 Września 2024
Konig

Konig SEC-ALARM200 Instrukcja

21 Sierpnia 2024
Konig

Konig SAS-ASPB300 Instrukcja

20 Sierpnia 2024
Konig

Konig SEC-ALARM110 Instrukcja

15 Sierpnia 2024

Instrukcje Dzwoni alarm

Najnowsze instrukcje dla Dzwoni alarm

Techno Line

Techno Line WT 189 Instrukcja

30 Grudnia 2025
Techno Line

Techno Line WT 759 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 755 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 499 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 495 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 3000 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 435 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 2500 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 250 Instrukcja

27 Grudnia 2024
Techno Line

Techno Line WT 293 Instrukcja

27 Grudnia 2024