Instrukcja obsługi Konig KN-STUDIO91
Konig
Inne akcesoria do aparatu
KN-STUDIO91
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Konig KN-STUDIO91 (32 stron) w kategorii Inne akcesoria do aparatu. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/32
2014-01-06
KN-STUDIO91
MANUAL (p. 2 )
Photo studio
ANLEITUNG (s. 4 )
Fotostudio
MODE D’EMPLOI (p. 6 )
Studio de photo
GEBRUIKSAANWIJZING (p. 8 )
Fotostudio
MANUALE (p. 10 )
Photo studio
MANUAL DE USO (p. 12 )
Foto estudio
HASZNÁLATI ÚTMUTATÓ (o. 14.)
Fotóstúdió
KÄYTTÖOHJE (s. 16 )
Valokuvastudio
BRUKSANVISNING (s. 18 )
Foto studio
NÁVOD K POUŽITÍ (s. 20 )
Foto studio
MANUAL DE UTILIZARE (p. 22 )
Studio foto
ΕΓΧΕΙΡΙ∆ΙΟ XPHΣ ΣH (σελ. 24 )
Photo studio
BRUGERVEJLEDNING (p. 26 )
Fotostudie
VEILEDNING (p. 28 )
Photo studio
KASUTUSJUHEND (lk 30)
Fotostuudio
2
ENGLISH
Photo studio
1. Test button
2. Photocell
3. ‘Ready’ indicator
4. Mains ON/OFF
5. Fuse
6. Modeling lamp switch ON/OFF
7. Sync cord
8. Flash power control
Flash Energy 150 W
Typical recycle time 2 Seconds
Stepless flash power control Full to 1/8
Recommended modeling lamp E14 bulb 75 W
Flash colour temperature Approx. 5500 K
Flash trigger Light, sync cord, manual infrared, radio.
Trigger voltage 12 V
Operating voltage 180-230 V
Output precision Within 1%
Operation:
Switch the unit ON and set the “Flash power control” and “Modeling lamp switch” as required. When the unit
has charged to the required level, the red “Ready” indicator will light. The “Test button” should be pressed to
ensure that the flash is of the required power. Plug in the “Sync cord” and connect to the camera shutter at “X”
synchronization. Alternatively, use the built-in “Photocell” or plug in the “Radio remote control receiver”.
Power supply connections
220 V AC 50 Hz. Use the main lead supplied to connect to the main supply.
Main ON/OFF switch
Set the red illuminated On/Off switch to “ ” to turn the unit ON.
Flash power selection
The unit can offer stepless power variation from full to 1/8, rotate the power control to adjust the power you
need.
Charge
When first switched to “ ”, the red illuminated ON/OFF switch will light up. When the unit has charged to the
level set by the flash power selector, the red “Ready” Indicator will light up again. Your flash light is now ready.
1 2 3
4
5
6
7
8
3
Synchronization
- Test button: For testing, or multiple flashes can be used.
- Sync socket: The standard 0.35 cm jack type socket on the rear panel of the unit may be used for direct
connection to a camera set to “x” synchronization. A “Radio remote control receiver” may also be plugged
into this socket.
- Photocell: The unit has a built-in photocell, enabling the unit to be triggered by the flash from any other
flash unit, or a small camera mounted flashgun. The photocell is mounted behind the red “Ready”
indicator on the rear panel.
Modeling lamp control
Set the yellow switch to “ ” to turn on the modeling lamp and keep it on all the time.
Fuse
The modeling and flash circuitry is protected by a single 7 amp fuse mounted on the rear panel. Never replace
the fuse with one of a different rating. Be sure to switch OFF the unit before changing the bulb or fuse.
Warning - high voltage
Do not touch the flashtube assembly for thirty minutes after disconnecting from the supply.
Safety precautions:
To reduce risk of electric shock, this product should ONLY be
opened by an authorized technician when service is required.
Disconnect the product from mains and other equipment if a
problem should occur. Do not expose the product to water or
moisture.
Maintenance:
Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty:
No guarantee or liability can be accepted for any changes and modifications of the product or damage caused
due to incorrect use of this product.
General:
- Designs and specifications are subject to change without notice.
- All logos brands and product names are trademarks or registered trademarks of their respective holders
and are hereby recognized as such.
- This manual was produced with care. However, no rights can be derived. König Electronic can not accept
liability for any errors in this manual or their consequences.
- Keep this manual and packaging for future reference.
Attention:
This product is marked with this symbol. It means that used electrical and electronic products should
not be mixed with general household waste. There is a separate collections system for these products.
This product has been manufactured and supplied in compliance with all relevant regulations and directives,
valid for all member states of the European Union. It also complies with all applicable specifications and
regulations in the country of sales.
Formal documentation is available upon request. This includes, but is not limited to: Declaration of Conformity
(and product identity), Material Safety Data Sheet and product test report.
Please contact our customer service desk for support:
via website: http://www.nedis.com/en-us/contact/contact-form.htm
via e-mail: service@nedis.com
via telephone: +31 (0)73-5993965 (during office hours)
NEDIS B.V., De Tweeling 28, 5215 MC ’s-Hertogenbosch, THE NETHERLANDS
Specyfikacje produktu
| Marka: | Konig |
| Kategoria: | Inne akcesoria do aparatu |
| Model: | KN-STUDIO91 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Konig KN-STUDIO91, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Inne akcesoria do aparatu Konig
18 Września 2024
28 Sierpnia 2024
13 Sierpnia 2024
Instrukcje Inne akcesoria do aparatu
- Inne akcesoria do aparatu Sony
- Inne akcesoria do aparatu Nikon
- Inne akcesoria do aparatu Thinkware
- Inne akcesoria do aparatu Lastolite
- Inne akcesoria do aparatu Axis
- Inne akcesoria do aparatu Metz
- Inne akcesoria do aparatu Hähnel
- Inne akcesoria do aparatu Kata
- Inne akcesoria do aparatu FeiYu-Tech
Najnowsze instrukcje dla Inne akcesoria do aparatu
4 Października 2024
4 Października 2024
4 Października 2024
4 Października 2024
2 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
28 Września 2024
21 Września 2024