Instrukcja obsługi Kodak ScanMate i1120

Kodak skaner ScanMate i1120

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kodak ScanMate i1120 (34 stron) w kategorii skaner. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/34

Safety

User precautions

• Place the scanner on a sturdy, level work surface capable of supporting 2.6 kg (5.72 lbs).

• Do not install the scanner in a location subject to dust, humidity or steam. This may cause electrical shock or fire.

• Make sure the electrical power outlet is located within 1.52 meters (5 feet) of the scanner and is easily accessible.

• Use only the power cord that was provided with the scanner. Using any other power cord may cause electrical shock and/or

damage the product.

• Be sure the power cord is securely plugged into the wall outlet. Failure to do so may cause electrical shock or fire.

• Do not damage, knot, cut or modify the power cord. This may cause electrical shock or fire.

• The scanner requires a dedicated power outlet. Do not use an extension cord or power strip with the scanner.

• Use only the AC adapter that is supplied with the scanner; Model HEG42-240200-7L. Do not use the scanner’s AC adapter

with any other product.

• Leave sufficient space around the power outlet so it can be easily unplugged in case of an emergency.

• Do not use the scanner if it becomes inordinately hot, has a strange odor, emits smoke, or makes unfamiliar noises.

Immediately stop the scanner and disconnect the power cord from the power outlet. Contact Kodak Service.

• Do not disassemble or modify the scanner or the AC power adapter.

• Do not move the scanner with the power cord and USB cable attached. This may cause damage to the cord/cable. Remove

the power cord from the wall outlet before moving the scanner.

• Material Safety Data Sheets (MSDS) for chemical products are available on the Kodak website at: www.kodak.com/go/msds.

When accessing the MSDSs from the website, you will be required to provide the catalog number of the consumable you

want the Material Safety Data Sheet for. See the section entitled, “Supplies and consumables” later in this guide for supplies

and catalog numbers.

Environmental information

• The Kodak ScanMate i1120 Scanner is designed to meet worldwide environmental requirements.

• Guidelines are available for the disposal of consumable items that are replaced during maintenance or service; follow local

regulations or contact Kodak locally for more information.

• The Kodak ScanMate i1120 Scanner contains lead in the circuit board solder, glass lens, mercury in the lamps, and

Chromium VI used as corrosion protection on the metal frame. Disposal of this material may be regulated due to

environmental considerations. For disposal or recycling information, contact your local authorities or, in the USA, visit the

Electronics Industry Alliance website: www.eiae.org.

• The product packaging is recyclable.

• The Kodak ScanMate i1120 Scanner is Energy Star compliant and is sh the default time set to 15 ipped from the factory with

minutes.

EMC statements

United States:

This equipment has been tested and found to comply wit

h the limits for a Class B digital device pursuant to Part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of these measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for additional suggestions.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment. Where shielded interface cables have been provided with the product or specified additional

components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to

ensure compliance with FCC regulation.

Korea: As this equipment has obtained EMC registration for household use, it can be used in any area including residential

areas.

Japan: This is a Class B product based on the standard of the Voluntary Control Council for interference by information

Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio

interference. Install and use the equipment according to the instruction manual.

Acoustic emission

Maschinenlärminformationsverordnung – 3, GSGV

Der arbeitsplatzbezogene Emissionswert beträgt <70 dB(A).

[Machine Noise Information Ordinance — 3, GSGV

The operator-position noise emission value is <70 dB(A).]

Power system connection

This product is also designed for Norwegian IT power system with phase-to-phase voltage 230V.

European Union

This symbol indicates that when the last user wishes to discard this product, it must be sent to appropriate

facilities for recovery and recycling. Please contact your local Kodak representative or refer to www.kodak.com/

go/recycle for additional information on the collection and recovery programs available for this product.

Specyfikacje produktu

Marka:	Kodak
Kategoria:	skaner
Model:	ScanMate i1120
Kolor produktu:	Black, Grey
Wysokość produktu:	147.5 mm
Szerokość produktu:	300.6 mm
Głębokość produktu:	157.3 mm
Waga produktu:	2700 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	ENERGY STAR
Port USB:	Tak
Obsługiwane systemy operacyjne Windows:	Tak
Obsługiwany systemy operacyjne Linux:	Tak
Głębokość koloru wejścia:	48 bit
Typ skanera:	Skaner z podajnikiem
Typ zasilacza:	AC/USB
Podwójne skanowanie:	Tak
Optyczna rozdzielczość skanowania:	600 x 600 DPI
Pojemność automatycznego podajnika papieru:	50 ark.
Standardowe interfejsy:	USB 2.0
Wersja USB:	2.0
Typ przetwornika obrazu:	CCD
Maksymalny format skanowania:	215 x 863 mm
Skanowanie w kolorze:	Tak
Skanowanie kliszy:	Nie
Maksymalny dzienny cykl pracy:	- stron(y)
Prędkość skanowania Flatbed (cz/b, A4):	3 s/str.