Instrukcja obsługi Klipsch SW-310

Klipsch subwoofer SW-310

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch SW-310 (20 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/20

SW-308 and SW-310

Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS!

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other appara-

tus (including ampliﬁers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wider blade or the third prong are provided for your safety. If the provided

plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories speciﬁed by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table speciﬁed by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualiﬁed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects ﬁlled with

liquids, such as vases, are placed on the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord

plug from the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

The exclamation point, within an equilateral triangle, is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the product.

The lightning ﬂash with arrowhead symbol within an equilateral triangle, is intended

to alert the user to the presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of

electrical shock to persons.

WARNING: To reduce the risk of ﬁre or electrical shock, do not expose this apparatus to rain or moisture.

WARNING: No naked ﬂame sources – such as candles – should be placed on the product.

WARNING: This product is intended to be operated ONLY from the AC Voltages listed on the back

panel or included power supply of the product. Operation from other voltages other than those

indicated may cause irreversible damage to the product and void the products warranty. The use

of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages

in which the product was not designed to operate. If the product is equipped with a detachable

power cord, use only the type provided with your product or by your local distributor and/or

retailer. If you are unsure of the correct operational voltage, please contact your local distributor

and/or retailer.

INSPECTION

We want your new speaker system to look as good as it did leaving the fac-

tory! Please check promptly for any transit damage. Carefully unpack your new

speaker system and verify the components against the packing list. In extreme

circumstances, items may have become damaged in transit. If any damage is dis-

covered, notify the delivery service and dealer where the system was purchased.

Make a request for inspection, and follow their instructions for evaluation. Be sure

to keep the product’s original shipping carton.

POSITIONING YOUR SW SUBWOOFER

Klipsch powered subwoofers are designed to reproduce deep bass and deliver

the impact that makes your movies and music come alive. Typically, optimum

performance will result if you place your subwoofer in a corner of the room on

the same wall as your front channel speakers (Refer to Figure 1). Please note that

room placement can have a dramatic effect upon the performance of your pow-

ered subwoofer. Corner placement, as suggested above, will increase the amount

of bass output, while placing the subwoofer along the middle of a wall, or out in

the room will decrease the amount of bass output. Experiment with a number of

different placement options and control settings to ﬁnd the one that best suits

your particular room and taste. When choosing your subwoofer’s location, keep

in mind that you will need to connect the subwoofer’s built-in ampliﬁer to an AC

power outlet.

CAUTION: Ensure that the subwoofer is unplugged from the AC wall outlet before

making any connections.

CONTROLS

“LINE IN” Connection - Most of today’s surround receivers (and pre-ampliﬁers)

have a line level subwoofer output labeled Subwoofer Pre Out, Sub Out, SW Out, etc.

If you have this output, connect one end of a subwoofer cable to it and connect the

other end of the cable into the subwoofer line input labeled LEFT/LFE. This connec-

tion allows the subwoofer to operate with both music and surround sound movies

(refer to your receiver manual). In absence of a subwoofer output on your receiver,

as an alternative hookup, you can connect Left and Right channel Pre-Amp Outputs

from your receiver (if provided) to the Left/LFE and Right input on the subwoofer.

“GAIN” Control - If your subwoofer is connected to a Subwoofer Output of a

surround receiver, ﬁrst set the subwoofer volume level control in the receiver to

the “half way” or “0 dB” position. Then increase the gain of the subwoofer until

the subwoofer’s volume level matches the output of your main speakers. After

this setup is completed, the volume control on your system’s main ampliﬁer or

pre-ampliﬁer will be the volume control for both your subwoofer and speak-

ers together. If your subwoofer is connected to the L/R Pre-Amp Outputs of a

receiver or connected via the High-Level connection to the receiver’s speaker

terminals, there will be no subwoofer volume in that receiver to set before setting

the subwoofer’s gain control.

“LOWPASS” Control - The crossover point chosen determines where low bass

frequencies are “handed off” from the speakers to the subwoofer. If setting the

crossover point in the receiver, turn the Lowpass Filter knob on the subwoofer

to the farthest point right (150Hz). Set the crossover point based on the size of

the main left/right speakers you are using in the system. As a general rule, for

larger, ﬂoorstanding speakers, set the crossover point between 50Hz-90Hz. If

using small bookshelf or “satellite” speakers for the mains, set the crossover point

between 90Hz-150Hz. The smaller the speaker, the higher the setting until the

bass frequencies blend well between the speakers and your subwoofer once your

system is completely hooked up. If your receiver does not have a crossover point

setting, set the Lowpass Filter on the subwoofer instead within the same recom-

mended settings. (See receiver manual for additional speaker setup info).

“PHASE” 0/180 - This control is used to acoustically match the subwoofer’s

output to your main speakers. Select a position, between 0° and 180°, in which

your subwoofer has more output at the listening position.

Power LED indicator - Located on the front bafﬂe, this LED indicates the operat-

ing status of the built-in ampliﬁer. The LED will light green when the ampliﬁer is

on and receiving a signal. If the LED is dark and not lit, the ampliﬁer is off. For

more information on the controls mentioned in this manual and on bass manage-

ment, see your dealer or visit www.klipsch.com.

C A U T I O N

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this

equipment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualified service personnel.

CARE AND CLEANING OF YOUR POWERED SUBWOOFER

Your subwoofer has a durable black satin ﬁnish that should only require dry dust-

ing or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based clean-

ers and harsh detergents. The brush attachment of your vacuum should remove

any dust from your subwoofer enclosure.

FCC AND CANADA EMC COMPLIANCE INFORMATION

NOTE: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not in-stalled and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Approved under the veriﬁcation provision of FCC Part 15 as a Class B Digital Device.

Caution: Changes or modiﬁcations not expressly approved by the manufacturer

could void the user’s authority to operate this device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry

Canada technical speciﬁcations were met.

This equipment complies with FCC and IC radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator and your body. This transmitter must

not be co-located or operating in conjunction with any other antenna or transmitter.

Le terme «IC:» avant le numéro de certiﬁcation radio signiﬁe seulement que les

spéciﬁcations techniques d’Industrie Canada ont été respectées.

Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites

ﬁxées pour un environnement non contrôlé. Cet appareil doit être installé et utilisé

avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet trans-

metteur ne doit pas être co-situé ou opérant en liaison avec toute autre antenne

ou transmetteur.

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that permitted for successful communication.

EU COMPLIANCE INFORMATION:

Eligible to bear the CE mark, Conforms to European Union Low Voltage Directive

2006/95/EC; Conforms to European Union EMC Directive 2004/108/EC and

European Union Directive 2005/32/EC for Ecodesign requirements.

WEEE NOTICE

Note: This mark applies only to countries within the European Union (EU) and Norway.

This appliance is labeled in accordance with European Directive

2002/96/EC concerning waste electrical and electronic equip-

ment (WEEE). This label indicates that this product should not be

disposed of with household waste. It should be deposited at an

appropriate facility to enable recovery and recycling.

PRODUCT REGISTRATION

• Klipsch will keep you up-to-date on new products and promotions

• Your personal information will never be resold

• This registration information is not used for warranty purposes.

Please retain your receipt for warranty claims.

Specyfikacje produktu

Marka:	Klipsch
Kategoria:	subwoofer
Model:	SW-310

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch SW-310, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje subwoofer Klipsch

Klipsch Reference Premiere RP-1200SW Instrukcja

4 Października 2024

Klipsch PRO-1000SW Instrukcja

3 Października 2024

Klipsch R-120SWi Instrukcja

26 Września 2024

Klipsch KSW-300 Instrukcja

21 Września 2024

Klipsch SW-310 Instrukcja

18 Września 2024

Klipsch RSW SUB Instrukcja

16 Września 2024

Klipsch LF-10 Instrukcja

14 Września 2024

Klipsch Reference Sub Instrukcja

5 Września 2024

Klipsch SPL-150 Instrukcja

29 Sierpnia 2024

Klipsch KSW-100 Instrukcja

20 Sierpnia 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

JL Audio SGR-10TW3 Instrukcja

13 Października 2024

Teufel T6 Instrukcja

13 Października 2024

Polk DB1040 Instrukcja

10 Października 2024

OSD Audio NERO DUAL X8 Instrukcja

9 Października 2024

OSD Audio NERO WSA Instrukcja

9 Października 2024

Kicker 51CWQ102 Instrukcja

9 Października 2024

Kicker 51CWQ122 Instrukcja

9 Października 2024

Kicker 43C84 Instrukcja

9 Października 2024

Kicker 51CWQ124 Instrukcja

9 Października 2024

OSD Audio FS12 Instrukcja

9 Października 2024