Instrukcja obsługi Klipsch SW-115

Klipsch subwoofer SW-115

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch SW-115 (24 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/24

SW-110, SW-112 and SW-115 Subwoofers

Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS!

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other appara-

tus (including ampliﬁers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wider blade or the third prong are provided for your safety. If the provided

plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories speciﬁed by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table speciﬁed by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualiﬁed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects ﬁlled with

liquids, such as vases, are placed on the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord

plug from the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

The exclamation point, within an equilateral triangle, is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the product.

The lightning ﬂash with arrowhead symbol within an equilateral triangle, is intended

to alert the user to the presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of

electrical shock to persons.

WARNING: To reduce the risk of ﬁre or electrical shock, do not expose this apparatus to rain or moisture.

WARNING: No naked ﬂame sources – such as candles – should be placed on the product.

WARNING: This product is intended to be operated ONLY from the AC Voltages listed on the back

panel or included power supply of the product. Operation from other voltages other than those

indicated may cause irreversible damage to the product and void the products warranty. The use

of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages

in which the product was not designed to operate. If the product is equipped with a detachable

power cord, use only the type provided with your product or by your local distributor and/or

retailer. If you are unsure of the correct operational voltage, please contact your local distributor

and/or retailer.

INSPECTION

We want your new speaker system to look as good as it did leaving the fac-

tory! Please check promptly for any transit damage. Carefully unpack your new

speaker system and verify the components against the packing list. In extreme

circumstances, items may have become damaged in transit. If any damage is dis-

covered, notify the delivery service and dealer where the system was purchased.

Make a request for inspection, and follow their instructions for evaluation. Be sure

to keep the product’s original shipping carton.

POSITIONING YOUR SW SUBWOOFER

Klipsch® powered subwoofers are designed to reproduce deep bass and deliver

the impact that makes your movies and music come alive. Typically, optimum

performance will result if you place your subwoofer in a corner of the room on

the same wall as your front channel speakers (Refer to Figure 1). Please note that

room placement can have a dramatic effect upon the performance of your pow-

ered subwoofer. Corner placement, as suggested above, will increase the amount

of bass output, while placing the subwoofer along the middle of a wall, or out in

the room will decrease the amount of bass output. Experiment with a number of

different placement options and control settings to ﬁnd the one that best suits

your particular room and taste. When choosing your subwoofer’s location, keep

in mind that you will need to connect the subwoofer’s built-in ampliﬁer to an AC

power outlet.

CONNECTIONS AND CONTROLS

CAUTION: Ensure that the subwoofer is unplugged from the AC wall outlet before

making any connections. Do not connect both “High Level” and “Line Level”

inputs at the same time as damage to your equipment could result!

“LINE IN” Connection - Most of today’s surround receivers (and pre-ampliﬁers)

have a line level subwoofer output labeled Subwoofer Pre Out, Sub Out, SW Out,

etc. If you have this output, connect one end of a subwoofer cable to it and con-

nect the other end of the cable into the subwoofer line input labeled LEFT/LFE.

This connection allows the subwoofer to operate with both music and surround

sound movies (refer to your receiver manual). In absence of a subwoofer output

on your receiver, as an alternative hookup, you can connect Left and Right chan-

nel Pre-Amp Outputs from your receiver (if provided) to the Left/LFE and Right

input on the subwoofer.

“HIGH LEVEL” Connection - If your receiver (or pre-ampliﬁer) does not have a

Subwoofer Pre Out, Sub Out, SW Out, etc. connection, you can connect the SW

subwoofer via the High Level Connection. Using 16 gauge or larger speaker

wire, connect the RED “positive” (+) terminal of your ampliﬁer’s LEFT channel to

the RED (+) terminal of your subwoofer’s LEFT channel (High Level In). Connect

the BLACK “negative” (-) terminal of your ampliﬁer’s LEFT channel to the BLACK

“negative” (-) terminal of your subwoofer’s LEFT channel input (High Level In).

Repeat this procedure for connecting your ampliﬁer’s RIGHT channel input. Take

care that no bare wires from any of the connections touch any other terminals,

or each other, as this could damage your equipment. This connection to your

receiver will be to the same terminals as your main speakers are connected to.

“GAIN” Control - If your subwoofer is connected to a Subwoofer Output of a sur-

round receiver, ﬁrst set the subwoofer volume level control in the receiver to the

“half way” or “0 dB” position. Then increase the volume (or gain) of the subwoofer

up until the subwoofer’s volume level matches the output of your main speakers.

After this setup is completed, the volume control on your system’s main ampliﬁer

or pre-ampliﬁer will be the volume control for both your subwoofer and speakers

together. If your subwoofer is connected to the L/R Pre-Amp Outputs of a receiver

or connected via the High-Level connection to the receiver’s speaker terminals,

there will be no subwoofer volume in that receiver to set before setting the sub-

woofer’s gain control.

“LOWPASS” Control - The crossover point chosen determines where low bass

frequencies are “handed off” from the speakers to the subwoofer. If setting the

crossover point in the receiver, turn the Lowpass Filter knob on the subwoofer

to the farthest point right (150Hz). Set the crossover point based on the size of

the main left/right speakers you are using in the system. As a general rule, for

larger, ﬂoorstanding speakers, set the crossover point between 50Hz-90Hz. If

using small bookshelf or “satellite” speakers for the mains, set the crossover point

between 90Hz-150Hz. The smaller the speaker, the higher the setting until the

bass frequencies blend well between the speakers and your subwoofer once your

C A U T I O N

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this

equipment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualified service personnel.

Specyfikacje produktu

Marka:	Klipsch
Kategoria:	subwoofer
Model:	SW-115

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch SW-115, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje subwoofer Klipsch

Klipsch Icon XW-500d Instrukcja

20 Lutego 2025

Klipsch Reference RW-12 Instrukcja

20 Lutego 2025

Klipsch KI-115-SMA-II Instrukcja

31 Grudnia 2025

Klipsch KI-215-SMA-II Instrukcja

31 Grudnia 2025

Klipsch RSW-10 Instrukcja

30 Grudnia 2025

Klipsch Reference RW-5802 II Instrukcja

8 Grudnia 2024

Klipsch Reference Premiere RP-1200SW Instrukcja

4 Października 2024

Klipsch PRO-1000SW Instrukcja

3 Października 2024

Klipsch R-120SWi Instrukcja

26 Września 2024

Klipsch KSW-300 Instrukcja

21 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

ETON Graphit 8-2 Instrukcja

19 Marca 2025

ETON Graphit 8-4 Instrukcja

19 Marca 2025

ETON Graphit 10-4 Instrukcja

19 Marca 2025

ETON MW 10 FLAT Instrukcja

19 Marca 2025

ETON PW 8 Instrukcja

19 Marca 2025

ETON USB 6 AR Instrukcja

19 Marca 2025

Morel Ultimo Powerslim 124D Instrukcja

12 Marca 2025

Morel Ultimo Powerslim 104D Instrukcja

12 Marca 2025

Rockustics OneSub Instrukcja

9 Marca 2025

Phase Technology PL-10s Instrukcja

5 Marca 2025