Instrukcja obsługi Klipsch RSA-500

Klipsch odbiornik RSA-500

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch RSA-500 (16 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
RSA-500
SUBWOOFER AMPLIFIER
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance
with the manufacturer's instructions.
8. DO NOT install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. DO NOT defeat the safety purpose of the polarized or grounding
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wider blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the
manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused
for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Do not expose this apparatus to dripping or splashing and
ensure that no objects filled with liquides, such as vases, are
placed on the apparatus.
16. To completely disconnect this apparatus from teh AC Mains,
disconnect the power supply cord plug from the AC receptacle.
17. The mains plug of the power supply cord shall remain readily
operable.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
this unit.
WARNING: To reduce the risk of fire or electrical shock, do not
expose this apparatus to rain or moisture.
WARNING: Voltages in this equipment are hazardous to life.
No user-serviceable parts inside. Refer all servicing to qualified
service personnel.
CAUTION: Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate this device.
ABOUT YOUR KLIPSCH PURCHASE
Thank you for your purchase of a Klipsch subwoofer amplifier.
After reading this manual and connecting your system, you will
hear the results of over 60 years of stringent engineering and
class-leading research and development. Again, thank you for
choosing Klipsch and we hope that your subwoofer amplifier
brings life to your music and movies for many years.
UNPACKING
The easiest way to remove the amplifier from its carton is to turn
the open end of the box down so that it is resting on a table or
the floor, with the flaps spread out and away. Then pull the box
straight up and off. Remove any packing material from the
amplifier, place it back in the carton, and store in case you ever
need to ship the amplifier.
FRONT PANEL CONTROLS
1. Lowpass Crossover
The Lowpass Crossover control allows you to select the proper
frequency at which your subwoofer system blends with your
main speakers. It is adjustable from 40-120Hz. You should set
this control to the approximate low-frequency limit of your main
left and right speakers.
2. Level Control
The Level control is the volume setting for the amplifier. It is used
in conjunction with the subwoofer output level control on your
preamplifier or receiver. It is used to adjust the overall output
level of your subwoofer system.
RSA-500 SUBWOOFER AMPLIFIER
English
Figure 1
Figure 2
REAR PANEL INPUTS AND OUTPUTS
/CONNECTIONS AND SETUP
Make all connections with the power turned “OFF” on both
the subwoofer amplifier and your receiver or preamplifier!
1. Speaker Level Inputs
The Speaker Level inputs which allow this amplifier to be used in
whole house distributed audio systems or with receivers that do
not feature line or subwoofer outputs. You may connect either
the inputs or outputs with Banana or pin connectors as well as
stripped wire up to 12 gauge.
2. Line Level Inputs and Outputs
The Line Level inputs consists of a pair of stereo jacks and a
single LFE RCA phono jack. Either one or both of the stereo jacks
may be used. (Use a shielded, high quality subwoofer
interconnect cable of appropriate length with RCA plugs on each
end. Your dealer can help you select a suitable cable.) Use
the LFE jack when you are using the crossover built into your
receiver or processor. The stereo inputs should be used when
you wish to utilize the crossover built into the RSA-500. The Line
Level outputs consist of a pair of gold plated stereo RCA jacks
and a single LFE RCA phono jack. This set of outputs are unfil-
tered pass through for both the Line Level and LFE input signals.
They can be used to connect to a second RSA-500 amplifier or
to connect back to your electronics if needed.
3. Phase Control
The Phase control on the RSA-500 is switchable between either
0˚ or 180˚. This control allows you to fine tune the performance
of your subwoofer system by optimizing the blend with the main
speakers. One of the positions may result in an audible increase
in bass output depending upon room placement.
4. Equalizer Selection
The Equalizer switch has four settings which are labeled 1
through 4. In the “1” position, the EQ curve selected is opti-
mized for the RW-5802 in-wall subwoofer. In the “2” position,
the EQ curve selected is optimized for the AW-800-SW outdoor
subwoofer. The position labeled “3” is for future use. The
position labeled “4” is for future use.
5. Power Mode Selection
The Power Mode switch has three settings – “Trigger”, “Auto”
and“On”. In the “Trigger” position, leave the Master Power switch
in the “On” position and set the Power Mode switch to the
“Trigger” position, then the amplifier will automatically turn itself
on and off when 5-30 volts DC is detected or removed from the
rear panel 1/8" Trigger jack. Tip is positive, ring is negative.
There is no delay when using the Trigger function. In the “Auto”
position, leave the Master Power switch in the “On” position and
set the Power Mode switch to the “Auto” position, then the
amplifier will automatically turn itself on and off when an audio
signal is detected or removed from the rear low or high level
inputs. There is a 2 second On delay and a 15 minute Off delay
when using the Auto Power function. In the “On” position, the
Master Power switch turns the amplifier on or off. Set the Master
Power switch to the “On” position and set the Power Mode
switch to the “On” position, then the amplifier will turn itself on
and off with the Master Power switch.
6. Speaker Level Outputs
The Speaker Level outputs may connected either with Banana or
pin connectors as well as stripped wire up to 12 gauge.
7. AC Line Cord and Main Switch
The AC Line connection uses a detachable two-prong power
cord. Insert the line cord into this jack, set the Master Power
switch located above the cord to “Off”, then insert the power
cord into an appropriate AC receptacle. Leave the Master Power
switch off until all connections are completed. (We recommend
leaving the Master Power and Power Mode switches in the “On”
position for normal operation in most systems.)
CONNECTIONS AND ADJUSTMENTS
The RSA-500 is a high-performance, power amplifier with a
built-in subwoofer crossover. It is designed specifically to drive
one or two subwoofer modules, such as the RW-5802, to maxi-
mum output without audible distortion or risk of damage.
Although the amplifier’s connections and controls are simple,
their use varies somewhat according to the subwoofer system’s
application. Typical setup procedures are described in the
following sections – one for digital systems and one for
analog systems.
DIGITAL SURROUND RECEIVER OR
PROCESSOR CONNECTIONS
Today’s Dolby Digital®and DTS®digital surround receivers and
processors, as well as all THX-certified models, have line-level
subwoofer outputs and built-in subwoofer crossovers. If your
system is built around one of these, it will almost always be best
to use the RSA-500’s LFE input. This will bypass the crossover
and level controls (Figure 3). Use a shielded, high quality sub-
woofer interconnect cable of appropriate length with RCA plugs
on each end. Your dealer can help you select a suitable cable. Be
sure to go into your receiver or processor’s speaker setup menu
and set Subwoofer to “On” or “Yes” in the subwoofer menu. Your
receiver or processor may have additional bass management
abilities beyond simply activating the subwoofer output. Consult
your receiver or processor’s owner’s manual or your dealer for
more information on the proper bass management settings for
your system.
• Crossover Adjustment – When the RSA-500’s LFE input is
used, the crossover control will not function.
Figure 3

Specyfikacje produktu

Marka: Klipsch
Kategoria: odbiornik
Model: RSA-500

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch RSA-500, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Klipsch

Klipsch

Klipsch VSX-935 Instrukcja

1 Stycznia 2025
Klipsch

Klipsch TX-RZ50 Instrukcja

1 Stycznia 2025
Klipsch

Klipsch VSX-835 Instrukcja

1 Stycznia 2025
Klipsch

Klipsch TX-SR393 Instrukcja

1 Stycznia 2025
Klipsch

Klipsch TX-RZ70 Instrukcja

1 Stycznia 2025
Klipsch

Klipsch VSX-LX105 Instrukcja

31 Grudnia 2025
Klipsch

Klipsch KVA-40 Instrukcja

14 Września 2024
Klipsch

Klipsch WA-3 Instrukcja

1 Września 2024
Klipsch

Klipsch RSA-500 Instrukcja

1 Września 2024
Klipsch

Klipsch PowerGate Instrukcja

24 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Audibax

Audibax Miami Instrukcja

5 Stycznia 2025
Audibax

Audibax Kansas Instrukcja

5 Stycznia 2025
AudioControl

AudioControl Epic Four Instrukcja

5 Stycznia 2025
Audibax

Audibax Zone 360 BT Instrukcja

5 Stycznia 2025
Audibax

Audibax Dayton 120T BT Instrukcja

5 Stycznia 2025
Audibax

Audibax Akron 2-2400 Instrukcja

5 Stycznia 2025
Audibax

Audibax Dayton 600 Instrukcja

5 Stycznia 2025
Audibax

Audibax Flint Kit Instrukcja

5 Stycznia 2025
Audibax

Audibax PA4250T Instrukcja

5 Stycznia 2025
Audibax

Audibax PA4500T Instrukcja

5 Stycznia 2025