Instrukcja obsługi Klipsch RPW-10

Klipsch subwoofer RPW-10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch RPW-10 (22 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/22

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance

with the manufacturer's instructions.

8. DO NOT install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wider blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched,

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the

manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused

for long periods of time.

14. REFER all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

This symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present within

this unit.

To reduce the risk of fire or electrical shock, do not expose this

product to rain or moisture. The product must not be exposed to

dripping and splashing and no object filled with liquids - such as a

vase of flowers - should be placed on the product.

No naked flame sources - such as candles - should be placed on the

product.

WARNING: The AC main plug should be located such that it remains

readily operable by the user.

WARNING: Voltages in this equipment are hazardous to life.

No user-serviceable parts inside. Refer all servicing to qualified

service personnel.

WARNING: This product is intended to be operated ONLY from the

AC Voltages listed on the back panel or included power supply of the

product. Operation from other voltages other than those indicated

may cause irreversible damage to the product and void the product’s

warranty. The use of AC Plug Adapters is cautioned because it can

allow the product to be plugged into voltages in which the product

was not designed to operate. If the product is equipped with a

detachable power cord, use only the type provided with your product

or by your local distributor and/or retailer. If you are unsure of the

correct operational voltage, please contact your local distributor

and/or retailer.

INSPECTION

We want your new speaker system to look as good as it did

leaving the factory! Please check promptly for any transit

damage. Carefully unpack your new speaker system and verify

the components against the packing list. In extreme circum-

stances, items may have become damaged in transit. If any

damage is discovered, notify the delivery service and dealer

where the system was purchased. Make a request for

inspection, and follow their instructions for evaluation. Be sure

to keep the product’s original shipping carton.

POSITIONING YOUR REFERENCE SERIES SUBWOOFER

Klipsch powered subwoofers are designed to reproduce deep

bass and deliver the impact that makes your movies and music

come alive. Typically optimum performance will result if you

place your subwoofer in a corner of the room on the same wall

as your front channel speakers (Refer to Figures 1 and 2). Please

note that room placement can have a dramatic effect upon the

performance of your powered subwoofer. Corner placement, as

suggested above, will increase the amount of bass output, while

placing the subwoofer along the middle of a wall, or out in the

room will decrease the amount of bass output. Experiment with a

number of different placement options and control settings to

find the one that best suits your particular room and taste. When

choosing your subwoofer’s location, keep in mind that you will

need to connect the subwoofer’s built-in amplifier to an AC

power outlet.

CONNECTIONS AND CONTROLS

CAUTION: Turn off your amplifier and your subwoofer before

making any connections. Do not connect both “High Level”

and “Line Level” inputs at the same time as damage to your

equipment could result!

“LINE IN” – This input is designed as the standard or default

input for the subwoofer. It accepts signals from the Left and

Right channel pre-amp, subwoofer or LFE outputs of your

electronics via the RCA jack inputs. Connect to the “RIGHT” and

or “LEFT/LFE” inputs on the subwoofer’s rear panel (Refer to

RPW-10 SUBWOOFER

English

Figure 3). Use a high quality, shielded cable for best results. This

can be in place of the conventional speaker wire connections

(“HIGH LEVEL IN”).

“HIGH LEVEL” – The RPW-10 powered subwoofer can

alternately be connected to the main channel speaker outputs

of your electronics via the “HIGH LEVEL IN” connectors on the

subwoofer’s rear panel. Using 16-gauge or larger speaker wire,

connect the RED “positive” (+) terminal of your amplifier’s LEFT

channel to the RED (+) terminal of your subwoofer’s LEFT

channel input (“HIGH LEVEL IN”). Connect the BLACK “negative”

(-) terminal of your amplifier’s LEFT channel to the BLACK

“negative” (-) terminal of your subwoofer’s LEFT channel input

(“HIGH LEVEL IN”). Repeat this procedure for connecting your

amplifier’s RIGHT channel to your subwoofer’s RIGHT channel

input (Refer to Figure 4). Take care that no bare wires from any

of the connections touch any other terminals as this could

damage your equipment.

“HIGH LEVEL OUT” – Connect your Left and Right channel

speakers to these terminals instead of those on your amplifier if

it is more convenient than connecting them directly to your

amplifier. These outputs pass through a full range (unfiltered)

signal. This requires that the subwoofer is connected to your

amplifier with the “HIGH LEVEL IN,” speaker level terminals

(Refer to Figure 4).

“LOW PASS” (LP) CROSSOVER – The crossover allows the

user to select the upper-frequency cutoff of the subwoofer. The

frequency is selectable from 40-120Hz. Frequencies above the

control’s setting are filtered out, allowing you to blend the

subwoofer’s output with that of your main speakers. If the

low pass filter function is being provided by your speaker’s

electronics, set the “LOW PASS” control to 120Hz.

“GAIN” – This control serves as a volume control for the

subwoofer. It is used to match the output level of the subwoofer

to your main speakers. The volume control on your system’s

main amplifier or pre-amplifier will be the overall volume control

for your subwoofer and full range speakers.

“PHASE” 0/180 – This control is used to acoustically match the

subwoofer’s output to your main speakers. Select the position,

either 0˚ or 180˚, in which your subwoofer has more output at

the listening position.

“POWER” ON/OFF– This is the main A/C power switch for the

subwoofer. This switch must be in the “ON” position for the

subwoofer to operate and for the “AUTO/ON” switch to function.

Set this switch to the “OFF” position if the subwoofer will not be

used for an extended period of time (i.e. vacation).

“AUTO/ON” – When this switch is in the “AUTO” position, the

subwoofer will automatically turn “on” when it senses a signal.

It will automatically turn “off” after 20 minutes with no signal.

When this switch is in the “ON” position, the subwoofer will

remain “on” as long as the “POWER” ON/OFF switch is in the

“ON” position.

Power LED indicator– Located on the rear amplifier panel, this

LED indicates the operating status of the built-in amplifier. The

LED will light red when the amplifier is in standby mode and

green when the amplifier is on and receiving a signal. For more

information on the controls mentioned in this manual and on

bass management, see your dealer or visit www.klipsch.com.

CARE AND CLEANING OF YOUR POWERED SUBWOOFER

Your subwoofer has a durable vinyl finish that should only require

dry dusting or cleaning with a dry cloth. Avoid the use of abrasive

or solvent-based cleaners and harsh detergents. The brush

attachment of your vacuum should remove any dust from your

subwoofer enclosure.

WARRANTY — U.S. AND CANADA ONLY

The Warranty below is valid only for sales to consumers in the

United States or Canada. KLIPSCH, L.L.C. ("KLIPSCH") warrants this

product to be free from defects in materials and workmanship (sub-

ject to the terms set forth below) for a period of five (5) years from

the date of purchase. During the Warranty period, KLIPSCH will

repair or replace (at KLIPSCH’s option) this product or any defective

parts (excluding electronics and amplifiers). For products that have

electronics or amplifiers, the Warranty on those parts is for a period

of two (2) years from the date of purchase.

To obtain Warranty service, please contact the KLIPSCH authorized

dealer from which you purchased this product. Proof of purchase in

the form of a bill of sale or receipted invoice, which is evidence that

this product is within the Warranty period, must be presented or

included to obtain Warranty service. This Warranty is invalid if (a) the

factory-applied serial number has been altered or removed from this

product or (b) this product was not purchased from a KLIPSCH

authorized dealer. You may call 1-800-KLIPSCH to confirm that you

have an unaltered serial number and/or you purchased from a

KLIPSCH authorized dealer.

This Warranty is only valid for the original purchaser and will

automatically terminate prior to expiration if this product is sold or

otherwise transferred to another party.

This Warranty does not cover cosmetic damage or damage due to

misuse, abuse, negligence, acts of God, accident, commercial use or

modification of, or to any part of, the product. This Warranty does

not cover damage due to improper operation, maintenance or

installation, or attempted repair by anyone other than KLIPSCH or a

KLIPSCH dealer which is authorized to do KLIPSCH warranty work.

Any unauthorized repairs will void this Warranty. This Warranty does

not cover product sold AS IS or WITH ALL FAULTS.

Specyfikacje produktu

Marka:	Klipsch
Kategoria:	subwoofer
Model:	RPW-10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch RPW-10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje subwoofer Klipsch

Klipsch Icon XW-500d Instrukcja

20 Lutego 2025

Klipsch Reference RW-12 Instrukcja

20 Lutego 2025

Klipsch KI-115-SMA-II Instrukcja

31 Grudnia 2025

Klipsch KI-215-SMA-II Instrukcja

31 Grudnia 2025

Klipsch RSW-10 Instrukcja

30 Grudnia 2025

Klipsch Reference RW-5802 II Instrukcja

8 Grudnia 2024

Klipsch Reference Premiere RP-1200SW Instrukcja

4 Października 2024

Klipsch PRO-1000SW Instrukcja

3 Października 2024

Klipsch R-120SWi Instrukcja

26 Września 2024

Klipsch KSW-300 Instrukcja

21 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

ETON Graphit 8-2 Instrukcja

19 Marca 2025

ETON Graphit 8-4 Instrukcja

19 Marca 2025

ETON Graphit 10-4 Instrukcja

19 Marca 2025

ETON MW 10 FLAT Instrukcja

19 Marca 2025

ETON PW 8 Instrukcja

19 Marca 2025

ETON USB 6 AR Instrukcja

19 Marca 2025

Morel Ultimo Powerslim 124D Instrukcja

12 Marca 2025

Morel Ultimo Powerslim 104D Instrukcja

12 Marca 2025

Rockustics OneSub Instrukcja

9 Marca 2025

Phase Technology PL-10s Instrukcja

5 Marca 2025