Instrukcja obsługi Klipsch IC-SW-8T
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch IC-SW-8T (6 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/6
I C - S W - 8 T I N - C E I L I N G S U B W O O F E R
OW N E R ’SM A N U A L A N D WA R R A N T Y
3. To install the tilebridge, fold the rail side of the ring back
upon itself using the spring tensioner on the reinforcement ring
to allow insertion into the cutout hole. Once it is inserted into
the cutout hole, release the reinforcement ring such that it
unfolds back to its normal position. Position tilebridge over
cutout hole.
4. The wiring compartment is intended as a termination point
for the audio circuit. Access to this compartment is gained by
removing the terminal cover located on the back of the
speaker. The terminal cover will accept the appropriate
conduit/wire adapter (provided). Feed wires through
conduit/wire adapter and connect to the input terminal
according to the desired operation mode. Be sure to observe
proper polarity. Replace the terminal cover and tighten the
conduit/wire adapter to secure the wire.
Caution: When connecting 70V or 100V dist ri b u t e d
line systems, t e care to ensure proper ta k e rm i n a l
connection. Connection to the low impedance t -e rm i
nal could r in speaker damage, ame s u l t p l i f i e r
d a m a g e, or both.
Thank you for purchasing yo u r
K l i p s c h IC-SW-8T i n-cei li ng subw . o o f e r
The IC-SW-8T in-ceiling speaker is designed for music reinforce-
ment applications. Unobtrusive, these loudspeakers are engi-
neered for easy, versatile installation.
The IC-SW-8T features a transformer-less design for 70.7V/100V
distributed-line systems. Some of the benefits of this design are:
Elimintation of transformer saturation at high output levels,
elimination of transformer insertion losses, improved bandwidth
(particularly at low frequencies), and improves power transfer to
the loudspeaker at low frequencies. For applications where 4
ohm mono or 8 ohm stereo operation is required, the mode of
operation can be selected by using an optional connection
located on the back input terminal and by properly setting the
rotary switch located under the grill.
Before installing your speakers take a moment to check the
contents of the cartons and make sure nothing has been
damaged in transit.
Content s Des cription Q U YA N T I T
Speaker Module 1
Grille 1
Reinfor 1cement Ring
Rails 2
Cardboard Cutout Template and Paint Mask 1
Screws (Attach Rails to Reinforcement Ring) 2
3/ 8" Adapter Fittings 1
1/ 2" Adapter Fittings 1
I nstallation Gu id el i nes
The IC-SW-8T includes a tilebridge for use when installing
the loudspeaker into suspended ceilings or wherever additional
reinforcement of the ceiling material is required. The tilebridge
and loudspeaker are designed such that installation may be
accomplished where access above the ceiling is not possible
or may be difficult.
I n s t a l l a t i o n
1. The tilebridge is composed of three parts—a reinforcement ring
and two rails. The two rails should be attached to the
reinforcement ring using the two included screws as shown below.
Caution: Be sure to com y with any and all building codesp l
in your are a .
2. To install your IC-SW-8T cut out a hole in the ceiling using either
the cardboard cutout template provided with your speakers or
consult the measurements below. Pull wiring through hole.
I C - - 8 T S U BS W W O O F E R
I C - S W - 8 T 121/
2" R o u n d
5. Insert the speaker into the cutout hole. With a #2 Phillips screw-
driver, tighten the four dog clamps until they are seated securely
against the ceiling surface. Do not overtighten.
6. For installations using 70v/100v input connection, set the
switch on the front panel to "70V/100V".
For low impedance, stereo applications, the switch should be
set to 8 ohms stereo.
For low impedance, mono applications, the switch should be
set to 4 ohm mono.
In all cases, please make sure the speaker wires are connect-
ed to the appropriate terminal on the back.
7. Using the flat of your hand, insert grille into speaker frame
making sure it is securely seated and flush.
Se i s m i c Ta b
A seismic tab, located on the back of the speaker, is used
as a secondary security point. Some construction codes may
require its use. To utilize the seismic tab, run a support wire
from a secure point in the ceiling and attach it to the tab.
Be sure to consult the construction codes in your area.
Klipsch recommends the use of this tab in all installations as
a secondary means of support.
IC-SW-8T tap selectable
Specyfikacje produktu
Marka: | Klipsch |
Kategoria: | subwoofer |
Model: | IC-SW-8T |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Klipsch IC-SW-8T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje subwoofer Klipsch
3 Października 2024
5 Września 2024
29 Sierpnia 2024
20 Sierpnia 2024
20 Sierpnia 2024
16 Sierpnia 2024
16 Sierpnia 2024
14 Sierpnia 2024
8 Sierpnia 2024
8 Sierpnia 2024
Instrukcje subwoofer
- subwoofer Yamaha
- subwoofer Pioneer
- subwoofer Bosch
- subwoofer JBL
- subwoofer Onkyo
- subwoofer Roland
- subwoofer KEF
- subwoofer Behringer
- subwoofer Boss
- subwoofer Marquant
- subwoofer Jensen
- subwoofer Blaupunkt
- subwoofer Speed-Link
- subwoofer Metra
- subwoofer Martin Logan
- subwoofer DAP-Audio
- subwoofer Phoenix Gold
- subwoofer Audac
- subwoofer Kenwood
- subwoofer Polk
- subwoofer Alpine
- subwoofer Dynaudio
- subwoofer Paradigm
- subwoofer JVC
- subwoofer Memphis Audio
- subwoofer Jamo
- subwoofer Nubert
- subwoofer LD Systems
- subwoofer Krüger&Matz
- subwoofer Audiotec Fischer
- subwoofer Fusion
- subwoofer Neumann
- subwoofer Magnat
- subwoofer Pyle
- subwoofer ELAC
- subwoofer Sonus Faber
- subwoofer Marantz
- subwoofer Bowers & Wilkins
- subwoofer Monitor Audio
- subwoofer Vonyx
- subwoofer Alto
- subwoofer Peavey
- subwoofer RCF
- subwoofer Harman Kardon
- subwoofer JL Audio
- subwoofer REL Acoustics
- subwoofer Teufel
- subwoofer Dali
- subwoofer Proel
- subwoofer Hifonics
- subwoofer Focal
- subwoofer Kicker
- subwoofer Omnitronic
- subwoofer Mackie
- subwoofer Deaf Bonce
- subwoofer SVS
- subwoofer Arcam
- subwoofer Infinity
- subwoofer McIntosh
- subwoofer Dynacord
- subwoofer Hertz
- subwoofer KRK
- subwoofer Atlas Sound
- subwoofer Definitive Technology
- subwoofer PowerBass
- subwoofer Power Dynamics
- subwoofer Kanto
- subwoofer Rockford Fosgate
- subwoofer Canton
- subwoofer Monacor
- subwoofer Tannoy
- subwoofer SPL
- subwoofer Indiana Line
- subwoofer HK Audio
- subwoofer Fenton
- subwoofer Sonance
- subwoofer Cabasse
- subwoofer Sonos
- subwoofer Musway
- subwoofer Renegade
- subwoofer Heco
- subwoofer MB Quart
- subwoofer Atlantic
- subwoofer QSC
- subwoofer Genelec
- subwoofer Apart
- subwoofer Bazooka
- subwoofer Eve Audio
- subwoofer Axton
- subwoofer Nxg
- subwoofer FBT
- subwoofer OSD Audio
- subwoofer Soundstream
- subwoofer PSB
- subwoofer Citronic
- subwoofer Wet Sounds
- subwoofer Mission
- subwoofer Morel
- subwoofer Mtx Audio
- subwoofer GoldenEar Technology
- subwoofer Velodyne
- subwoofer Chrysalis
- subwoofer IMG Stage Line
- subwoofer Fluance
- subwoofer Pyramid
- subwoofer Sound Ordnance
- subwoofer MadBoy
- subwoofer Totem
- subwoofer Mirage
- subwoofer KLH Audio
- subwoofer Alphasonik
Najnowsze instrukcje dla subwoofer
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024