Instrukcja obsługi Klein Tools NCVT-2

Klein Tools Sprzęt pomiarowy NCVT-2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klein Tools NCVT-2 (8 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

NON-CONTACT VOLTAGE TESTER

(NCVT-2) OwNER’S MANuAL

Fig. 1

Locking tab

Lengüeta de ﬁjación

Languette de

verrouillage

Probe

Punta de prueba

Sonde

Body /Cuerpo/Corps

Cap /Tapa/Capuchon

Power button

Botón de encendido

Interrupteur

Fig. 2

Gently push down on locking tab.

Empuje suavemente hacia abajo.

Appuyez doucement sur la languette de verrouillage.

AAAAAA

Fig. 4

While pushing down on tab, slide cap off body.

Mientras empuja hacia abajo sobre la lengüeta, deslice la

tapa hasta separarla del cuerpo.

Tout en appuyant sur la languette, faites glisser le capuchon

pour le détacher du corps du détecteur.

Align channel tabs on cap with slots on

tester body (one on each side of tester).

Alinee las lengüetas de canal ubicadas en la

tapa con las ranuras ubicadas en el cuerpo del

probador (una a cada lado del probador).

Alignez les languettes à proﬁlés sur le

capuchon avec les fentes du corps du dé-

tecteur (une de chaque côté du détecteur).

Slide cap onto body.

Deslice la tapa

sobre el cuerpo.

Faites glisser le capuchon

sur le corps du détecteur.

Align locking tab with cap.

Alinee la lengüeta de ﬁjación con la tapa.

Alignez la languette de verrouillage avec le capuchon.

Hold pocket-clip on cap close to tester body while sliding cap onto tester.

Sujete el clip para bolsillo ubicado en la tapa cerca del cuerpo del probador

mientras desliza la tapa sobre el probador.

Maintenez la pince-agrafe sur le capuchon à proximité du corps du détecteur

tout en faisant glisser le capuchon sur le détecteur.

Fig. 3

KLEIN TOOLS, INC.

Chicago, IL USA

www.kleintools.com

139805 Rev. 01/15 B

DuAL RANGE

MANUAL DEL USUARIO DEL PROBADOR DE TENSIÓN

SIN CONTACTOS DE INTERVALO DUAL (NCVT-2)

DéTECTEUR DE TENSION SANS CONTACT À

DOUBLE PLAGE (NCVT-2) - MODE D’EMPLOI

ENGLISH

SYMBOLS ON TESTER:

Warning. Risk of electric shock.

Risk of danger. Important information: It is important that users of this tester read,

understand, and follow all warnings, cautions, safety information, and instructions in this manual

before operating or servicing this tester. Failure to follow instructions could result in death or

serious injury.

Double Insulated.

Equipment is designed to protect against transients from the primary supply level.

(i.e. - electricity meter or overhead/ underground utility service).

OPERATING INSTRUCTIONS:

Modes of operation:

The NCVT-2 can operate as a dual range (NCVT-2 mode) or single range (NCVT-1 mode) tester. In

NCVT-2 mode, the tester will light a steady blue LED in the tip to indicate power-on and dual range

mode. In NCVT-1 mode, the tester will light a steady green LED in the tip to indicate power-on and

single range mode.

Turn unit on:

Press and hold the power button for ½ second, then release. Listen for single-beep sound and

watch for a steady green or blue LED to illuminate in the tip of the tester. The tester is now

activated and is operational. Test on known live circuit to verify tester functionality. See Silent

mode for additional power-on options.

Turn unit off:

Press and hold the power button for ½ second then release. Listen for a double-beep sound and

watch the green or blue LED turn off. The tester is now deactivated and is not operational.

System self-test:

The “power on” blue or green LED visually conﬁrms battery sufﬁciency, system integrity, and

operation/active mode. Always test on known live circuit to verify tester functionality prior to use.

Changing operation modes:

While the unit is powered on, press and hold the power button for 2 seconds. The power-on LED

will switch from blue to green or green to blue. The tester will start in whichever mode it was last

powered off in.

Checking for the presence of AC voltage:

Prior to use, test on known live circuit to verify tester functionality. Place tip of the tester near an

AC voltage and refer to the tables below for each mode:

NCVT-2 mode:

POWER-ON 12 TO 48 VOLTS AC 48 TO 1000 VOLTS AC

Audible

Single Beep Low-Pitched Pulsing Beeping Sound

High-Pitched Continuous Beeping Sound

Visual

Steady Blue LED

Blue LED Turns OFF and Red LED

Blinks (approx. 2-times per second).

Blue LED Turns OFF and Red LED

illuminates continuously.

NCVT-1 mode:

POWER-ON 12 TO 48 VOLTS AC 48 TO 1000 VOLTS AC

Audible

Single Beep No Sound

High-Pitched Continuous Beeping Sound

Visual

Steady Green LED Steady Green LED Green LED Turns OFF and Red LED

illuminates continuously.

In NCVT-2 mode, the tester will be more sensitive and will show voltage indication at a further

distance away from a high voltage source than in NCVT-1 mode. Use NCVT-1 mode in situations

where you expect the voltage source will be greater than 48V AC.

Low battery indication:

Scenario 1 – Powering on the tester: The “power on” LED in the tip of the tester changes from a

steady green or blue to a blinking green or blue and a series of beeping sounds is generated. The

tester then turns off. The unit is now deactivated and is not operational, the batteries require replace-

ment. To replace the tester batteries refer to the Maintenance section titled “Battery Replacement.”

Scenario 2 – Operating the tester: If the LED lights dim and the tone fades, the tester may require new

batteries. To replace the tester batteries refer to the Maintenance section titled “Battery Replacement.”

Auto Power Off:

After 4 minutes of non-use, the tester automatically powers off to conserve battery life. Listen for

a double-beep sound and watch the “power on” LED turn off. The tester is now deactivated and

is not operational.

Silent mode:

The tester can be operated with only visual indication of voltage. With the tester powered off, press

and hold the power button for 2 seconds then release.

MAINTENANCE:

Battery Replacement:

• Orient the tool/tester with the pocket-clip facing you.

• Gently depress the tab, Fig. 2, until you can slide the end-cap off the main body of the tester.

• Remove the batteries using caution to prevent damage or injury to the internal components.

• Replace with two 1.5V AAA or LR03 or NEDA 24A batteries.

• Place batteries into tester with the positive terminals facing the tip, Fig. 3.

• Carefully align and slide the end-cap to the body of the tester, Fig. 4. Push the cap until it is

fully seated (denoted by a clicking sound), Fig. 4.

• Note: Hold pocket-clip on cap close to tester body while sliding cap onto tester.

• Test on known live circuit to verify tester functionality.

CAT

SPECIFICATIONS:

VOLTAGE RANGE: 12-1000 Volts AC

TESTER TYPE: Non-Contact Voltage Detector

UL CERTIFICATION

E321008 3TMV

FREQUENCY RANGE:

50-500Hz

STAN DARDS:

UL 61010-1 2

edition, CAN/CSA C22.2 No.

61010-1-04, EN 61010-1 2

edition, IEC

61010-1:2001 2

edition, ISA-82.02.01

(IEC61010-1 MOD)

CAT IV RATED: 1000 V

DOUBLE INSULATED

POWER ON INDICATOR AND ILLUMINATOR:

Visual: High Intensity Green/Blue LED

POWER OFF & AUTO POWER OFF:

Visual: High Intensity Green LED Blinks

Audible: Double Beeping Sound

LOW BATTERY INDICATORS:

Visual: Green/Blue LED Blinks

Audible: Series of Beeping Sounds

VOLTAGE DETECTION INDICATORS:

12 VOLTS TO 48 VOLTS:

Visual: High Intensity Blinking Red LED

Audible: Low Pitched, Pulsing Beeping Sound

48 VOLTS TO 1000 VOLTS

Visual: High Intensity Continuously

Illuminated Red LED

Audible: High Pitched, Continuous

Beeping Sound

OPERATING CONDITIONS:

Temperature: 32° to 104° F (0° to 40° C)

Relative Humidity: <80%

Altitude: Up to 6,562 feet (2,000 meters) max.

Environment: Indoor Use

STORAGE CONDITIONS:

Temperature: 32° to 104° F (0° to 40° C)

Relative Humidity: <80%

Altitude: Up to 6,562 feet (2,000 meters) max.

Environment: Indoor

POLLUTION DEGREE: 2

BATTERIES: Two 1.5 volt AAA

or IEC LR03 or NEDA 24A

PATENTS: US D583,266 S

DISPOSAL: DO NOT THROW IN TRASH;

PLEASE RECYCLE.

CAT

CAuTION:

• Do not attempt to repair this tester. It contains no serviceable parts.

• Do not expose the product to extremes in temperature or high humidity.

wARNINGS:

• It is important that users of this tester read, understand, and follow all warnings, cautions, safety

information, and instructions in this manual before operating or servicing this tester. Failure to

follow instructions could result in death or serious injury.

• Risk of electric shock and burn. Contact with live circuits could result in death or serious injury.

• Use caution with voltages above 30V AC as a shock hazard may exist.

• A blinking or steady red glow and an audible beep indicate voltage present. If no indication, voltage

could still be present.

• Never assume neutral or ground wires are de-energized. Neutrals in multi-wire branch circuits may be

energized when disconnected and must be retested before handling.

• The tester detect voltage if:WILL NOT

• the wire is shielded.

• the operator is not grounded or is otherwise isolated from an effective earth ground.

• the voltage is DC.

• The tester MAY NOT detect voltage if:

• the user is not holding the tester.

• the user is insulated from the tester with a glove or other materials.

• the wire is partially buried or in a grounded metal conduit.

• the tester is at a distance from the voltage source.

• the ﬁeld created by the voltage source is being blocked, dampened, or otherwise interfered with.

• the frequency of the voltage is not a perfect sine wave between 50 and 500Hz.

• the tester is outside of operation conditions (listed in Speciﬁcations section).

• Operation may be affected by differences in socket design and insulation thickness and type.

• In bright light conditions, the LED visual indicators will be less visible.

• Do not use if "power on" LED is not illuminated.

• Do not use if tester appears damaged or if the tester is not operating properly. If in doubt, replace the tester.

• Do not apply more than the rated voltage as marked on the tester (1000 volts AC).

• Detection above 12V is speciﬁed under "normal" conditions as speciﬁed below. The tester may

detect at a different threshold at different conditions, or may not detect at all unless:

• The tip of the tester is within 0.25" of an AC voltage source radiating unimpeded.

• The user is holding the body of the tester with his or her bare hand.

• The user is standing on or connected to earth ground.

• The air humidity is nominal (50% relative humidity).

• The tester is held still.

• Always wear approved eye protection.

• Comply with local and national safety requirements.

• If this product is used in a manner not speciﬁed by the manufacturer, protection provided by the

product may be affected.

Cleaning Tester:

• Tester contains sensitive electronic components; do not submerse in liquid.

• Do not use alcohol, ammonia or cleaners containing solvents to clean tester.

• Gently wipe the tester with Klein Kleaners

(CAT. # 51425), a damp cloth or

a cloth containing a mild cleaning solution.

• Make sure the tester is completely dry prior to operation.

DISPOSAL:

• Do not throw depleted batteries away; please recycle properly.

• Do not throw tester away, please recycle properly.

• Please see or www.epa.gov www.erecycle.org for additional information.

WARRANTY: www.kleintools.com/warranty

Specyfikacje produktu

Marka:	Klein Tools
Kategoria:	Sprzęt pomiarowy
Model:	NCVT-2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klein Tools NCVT-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt pomiarowy Klein Tools

Klein Tools VDV501-770 Instrukcja

9 Października 2024

Klein Tools ET18 Instrukcja

9 Października 2024

Klein Tools VDV211-048 Instrukcja

9 Października 2024

Klein Tools ET500 Instrukcja

6 Października 2024

Klein Tools NCVT-2 Instrukcja

6 Października 2024

Klein Tools 45001 Instrukcja

5 Października 2024

Klein Tools HVNCVT-1 Instrukcja

5 Października 2024

Klein Tools TI220 Instrukcja

4 Października 2024

Klein Tools TI222 Instrukcja

4 Października 2024

Klein Tools TI290 Instrukcja

4 Października 2024

Instrukcje Sprzęt pomiarowy

Najnowsze instrukcje dla Sprzęt pomiarowy

Stamos S-LS-28 Instrukcja

15 Października 2024

Stamos S-LS-86 Instrukcja

15 Października 2024

Stamos S-LS-61 Instrukcja

15 Października 2024

Stamos S-LS-81 Instrukcja

15 Października 2024

Stamos S-LS-84 Instrukcja

15 Października 2024

Stamos S-LS-74 Instrukcja

15 Października 2024

Stamos S-LS-76 Instrukcja

15 Października 2024

Stamos S-LS-42 Instrukcja

15 Października 2024

Stamos S-LS-75 Instrukcja

15 Października 2024

Stamos S-LS-35 Instrukcja

15 Października 2024