Instrukcja obsługi Klavis Quadigy

Klavis nieskategoryzowany Quadigy

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klavis Quadigy (15 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/15

Quadigy

Quadigy Quadigy user manual V1.2 Page of 1 15

QuQuad

adadi

iigy

gygy Quad Envelope Generator

7-stage envelopes, presets, cycling, morphing & CV matrix

Introduction

The Quadigy is a complex envelope generator focused on live . The goal is to allow the user play

setting up rich, interactive and dynamically evolving envelopes without the risk of breaking up a

subtle and intricate once on stage. This is achieved by oering two main modes, one where patch

full control is , and a Live mode where only the settings that are sensible using on stage available

are accessible. The user interface oers an intuitive access for otherwise complex settings.

Advanced features such as automatic time-stretching, multiphase clocking and full morphing put

the Quadigy in a category on its own.

Quadigy

QuadigyQuadigy

Features at a glance

 Quad 7-stage envelopes

o Pre-delay

o Hold

o Attack

o Punch

o Decay

o Sustain

o Release

 Continuous curve shape setting

 Inversion

 Independent output level

 Cycle capability with auto t- -clock to

o Elastic time stretching

o 5 internal clocks with tap tempo

o External clock control

o Multiply/divide and oset

o Individual cycle ext. control

 Manual gating for convenient editing

 32 presets with naming

 External preset control via CV Trig or

 Simultaneous 156-point CV matrix

 Morphing on presets and CV Matrix

 Multi-editing for polyphonic uses

 Live mode for easier/safer control

 Graphical display

 Real-time envelope stages LED indication

 Current state retained over power cycle

 Easy rmware update via an audio le

 Ski-friendly and compact module

Quadigy

Quadigy Quadigy user manual V1.2 Page of 2 15

Installation and security

Purpose

This module is meant for installation in a Eurorack-compliant chassis.

It adheres to Eurorack Doepfer mechanical and electrical specications.

Do not attempt using this module in other mechanical or electrical contexts.

Installation

Before the installation, disconnect the mains power supply from your modular system. Some

power supplies are not safely isolated; there is a risk of injury!

See in the specications if this module requires 5V from the supply rails. If 5V is needed and your

rack is not providing 5V, do not attempt connection!

Check that the current consumption requirements of this module, when added to your installed

set of modules do not exceed the available current from your supply. This is done by adding up

the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. If any of these 3

sums exceeds the available current of your supply for that voltage, do not connect the module to

your system; you need a stronger power supply.

The provided supply at cable can only be inserted in the appropriate orientation at the back of

the module, so there is no risk of error on that end. However, you should pay attention to the

orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets

without shrouding may allow you to plug in the connector the wrong way!

The red stripe on the cable should match a stripe printed on the supply board. The stripe also

indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the

orientation.

Double check that the connectors are fully inserted and correctly oriented before switching on

the power supply. In case of an anomaly, switch o the power supply immediately and check

everything again.

Quadigy

Quadigy Quadigy user manual V1.2 Page of 3 15

Firmware update

If needed, the product can be updated by playing an audio le such as “Quadigy 1.00.wav”._

Check on Klavis.com that you have the latest rmware version for your product.

If there is none to be found, there is none needed ;-)

Procedure

 Connect a mono or stereo cable between your audio playing device headphone output

and the Quadigy CV A input.

 Prepare to play the audio le

 Set the play level at two thirds

 While pressing the Preset and CV Matrix buttons, switch on your modular case supply

 The display provides instructions

 Start playing the audio le

If everything goes fine

 The display tells “updating”

 As the update is progressing, a row is lling up

 When the row is full, all green LEDs ash; the rmware is updated successfully

 Press any button to restart the module

If the sound level is too low

 Stop audio playback

 Slightly increase the audio playback level

 Start audio playback from the beginning

If there is an error during the playback

The 7 red LEDs will ash and the display will indicate an error.

It is possible that the sound setting was too loud to begin with.

Diminish the sound level drastically and restart the procedure.

Playback error can also be due to various parasitic sound causes:

 Touching the cable

 Using sound-generating features of your phone or computer

 Some power saving feature aecting the audio playback

 Surrounding noisy modules, bad electrical grounding or modular supply noise

 Check that you have not created a ground loop (e.g. computer used as le player!)

Specyfikacje produktu

Marka:	Klavis
Kategoria:	nieskategoryzowany
Model:	Quadigy

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klavis Quadigy, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje nieskategoryzowany Klavis

Klavis Flexshaper Instrukcja

14 Lipca 2024

Klavis CalTrans Instrukcja

14 Lipca 2024

Klavis Dual CV Instrukcja

12 Lipca 2024

Klavis Twin Waves MKII Instrukcja

12 Lipca 2024

Klavis Mixwitch Instrukcja

12 Lipca 2024

Klavis Logica XT Instrukcja

12 Lipca 2024

Klavis Quadigy Instrukcja

12 Lipca 2024

Klavis Twin Waves Instrukcja

12 Lipca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024

Emko EZM-9920 Instrukcja

27 Października 2024

Emko ESM-3712-H Instrukcja

27 Października 2024

Emko ATS-10 Instrukcja

27 Października 2024

Emko EAOM-11.2 Instrukcja

27 Października 2024

Emko EPM-3790 Instrukcja

27 Października 2024

Emko EPM-7790 Instrukcja

27 Października 2024

Livarno Lux IAN 108340 Instrukcja

27 Października 2024

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024