Instrukcja obsługi Kenwood KNA-SPM100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kenwood KNA-SPM100 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
KNA-SPM100
Speed Pulse Generator for KENWOOD Wireless Apple CarPlay Ready Receivers
KNA-SPM100 OBD-II Speed Pulse Generator
The KNA-SPM100 provides a simplified method for obtaining a vehicle’s speed pulse
information. It requests a vehicle’s speed using OBD-II and then generates a speed pulse
to be provided to the receiver.
Compatible with most vehicles 2008 - Present
Pre-programmed to work once installed
Small footprint for easy installation
Simple 3-wire hookup and OBD-II connection cable
Red Wire - Connect to 12V Switched
Power
Black Wire - Connect to Ground
Purple/ Wire - Connect to
Receiver’s Speed Sense WirePink
OBD-II Plug - Connect to Vehicle’s
OBD-II Plug
Molex Plugs - Connect all to
KNA-SPM100 Interface
1. Power Receiver On.
2. The KNA-SPM100 interface LED will
blink 2 times, then OFF. RED
3. The KNA-SPM100 has successfully
programmed and is ready for use.
Connections Installation Instructions
If the KNA-SPM100 interface
did not blink 2 times, then RED
OFF, please refer to page 2.
White
KNA-SPM100
FAQ & Troubleshooting
LED Diagnostics FAQ
Receiver Messages
LED Blinks IndenitelyRED
» KNA-SPM100 did not receive a
response from the vehicle.
- This means that the KNA-SPM100
is not compatible with that vehicle.
»CAN wires are disconnected.
- Verify CAN wire connections.
How can I verify if a vehicle is compatible?
» Verify that the vehicle’s year of
production is 2008+ and has an OBD-II plug.
»The KNA-SPM100 will not work If the
vehicle doesn’t allow a scan tool to be
plugged into it while the vehicle is turned
on and/or while driving. Vehicle’s that
may exhibit this symptom typically include
high-end European models.
»Ultimately, the only other way to verify if
the KNA-SPM100 is compatible is to connect
it to a vehicle and verify the LED sequence.
LED Blinks / During that RED GREEN
Ignition Cycle
»KNA-SPM100 has detected another
OBD-II device, MRR, or another
radio replacement interface module
communicating on the bus.
- The KNA-SPM100 cannot be
used in conjunction with another OBD-II
device or MRR (please refer to the MRR or
radio replacement interface instructions
for vehicle speed pulse connection).
If you are still receiving a message like
this when attempting to use Wireless
Apple CarPlay while the vehicle is in
motion:
- The receiver is not receiving a proper
and/or any vehicle speed information.
- The GPS antenna is not connected
or an incorrect GPS antenna is being used.

Specyfikacje produktu

Marka: Kenwood
Kategoria: Niesklasyfikowane
Model: KNA-SPM100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kenwood KNA-SPM100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Kenwood

Kenwood

Kenwood UBZ-LJ9 Instrukcja

7 Października 2024
Kenwood

Kenwood CA-DR1130 Instrukcja

7 Października 2024
Kenwood

Kenwood LS-600BT Instrukcja

3 Października 2024
Kenwood

Kenwood KFC-XW1000F Instrukcja

22 Września 2024
Kenwood

Kenwood DDX795 Instrukcja

10 Września 2024
Kenwood

Kenwood DDX6703S Instrukcja

9 Września 2024
Kenwood

Kenwood DDX775BH Instrukcja

6 Września 2024
Kenwood

Kenwood DDX595 Instrukcja

5 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024