Instrukcja obsługi Kenwood Excelon CA-POD14AC

Kenwood Niesklasyfikowane Excelon CA-POD14AC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kenwood Excelon CA-POD14AC (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-POD14AC
6.5” AIR COOLED LOWER FAIRING SPEAKER ADAPTORS DESIGNED
AND ENGINEERED FOR 2014+ HARLEY-DAVIDSON® TOURING
MODEL MOTORCYCLES WITH OE OR AFTERMARKET AIR COOLED
LOWERS
INSTRUCTION MANUAL
JVCKENWOOD Corporation
2
6.5” Air Cooled Lower Fairing Speaker Adaptors Installation
Figure 1.1
Installation procedure
1. Remove the outer fairing/headlamp assembly (a towel on the front fender can help
prevent scratches or “dings” from dropped tools or fasteners etc.). Refer to a service manual
if you need help with this.
NOTE: The CA-POD14AC lower adaptors are MUCH easier to install with the lower fairings
OFF the bike. The next steps assume the lower fairings are OFF the bike, so please remove
them before proceeding.
2. When the lower fairings came othe bike, there was a painted “cap” that came o that
exposed the fasteners that hold the top of the lower to the upper crash bar. Looking into
the lower fairing from the area that was covered by the cap, you will see 3 screws that
hold the front panel to the lower fairing. Remove these 3 screws and undo the “slider arm”
from the vent so the front panel with the slider arm can come o the lower fairing. The 3
screws just removed will be re-used.
3. Depending on the lower fairings you have, if you have a “pocket” attached to the back
side of the front panel, it will need to be removed to gain access to the fastener that holds
the vent adjuster “handle” in place. With this pocket removed, undo the fastener that
secures the “handle” and put the handle aside for now.
5. Locate the wire harness that came with the CA-POD14AC kit. You will see this harness
has one longer 4-wire section that splits into two 2-wire sections. Each 2-wire section is
labeled “clutch side” or “brake side”. Take the appropriate short section and put it in the
correct side’s lower fairing so the speaker connectors are inside. Leave these loose for now.
6. Install the “vent adjuster handles” with arms into each lower speaker adaptor. Bring
the speaker adaptors to the lower fairing and put the speaker wires through the square
opening so they go into the speaker’s enclosure. With the wires in place, attach the arm
back into the vent. The speaker adaptor will now sit in place on the lower fairing. Using
the 3 screws removed earlier, secure the speaker adaptor to the lower fairing.
4. Using Fig 1.1 for reference, drill a 3/8"
(10mm) hole in the area highlighted by the
white circle into each lower to allow the
speaker wires to go in.
NOTE: Starting with a smaller drill bit and
working your way up to the full size is a good
idea. “Step bits” also work great for this. Make
sure to clean up any plastic “burrs” so they
don’t cut the speaker wires over time.
6.5” Air Cooled Lower Fairing Speaker Adaptors Installation - Cont.
3
7. Mount the lower fairings back to the bike but leave the painted caps o for now.
8. From the back side of each lower fairing, you can now take up the extra wire. Make it so
the wires aren't “too loose” or “too tight” (ensuring to leave enough wire in the pod for the
speaker to easily be plugged in and removed). The kit comes with strips of black gummy
material. Use this like a putty to hold the wire in place and seal up the hole drilled earlier.
9. Take the 4-wire section of the lower harness and plug it into the wires coming out of
each lower fairing, noting they will only go together one way. The rest of the harness will
work its way up to the inside of the fairing. If you are using the KENWOOD XM160-2 amp,
the 4-pin plug will go directly to it. If you are using a dierent brand of amplier, the blue/
black is the brake side, and the brown/black is the clutch side (note that the black wires
are the positive (+)).
10. Re-install the painted caps.
NOTE: Now is the best time to use zip ties to properly secure and “clean up” any wiring. It’s
always a good idea to remove excess from the zip ties by cutting them as close to ush as
possible so there are no sharp edges.
11. Take the speakers you will install and plug the speakers in (black wire is the positive
(+)). Secure the speakers to the lower fairings using the supplied machine screws.
NOTE: The “nutserts” molded into the lower fairings are brass, which is a soft material. DO
NOT OVERTIGHTEN THE SCREWS AND DO NOT USE A “THREAD LOCKING MATERIAL” OF
ANY KIND. A hand screwdriver is suggested for this step.
Before re-installing the outer fairing, turn the front
wheel to each extreme side, making sure any wiring
is not impeding the steering of the motorcycle.
Failure to do so can result in serious injury or death!

Specyfikacje produktu

Marka: Kenwood
Kategoria: Niesklasyfikowane
Model: Excelon CA-POD14AC

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kenwood Excelon CA-POD14AC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Kenwood

Kenwood

Kenwood UBZ-LJ9 Instrukcja

7 Października 2024
Kenwood

Kenwood CA-DR1130 Instrukcja

7 Października 2024
Kenwood

Kenwood LS-600BT Instrukcja

3 Października 2024
Kenwood

Kenwood Excelon CA-POD14AC Instrukcja

25 Września 2024
Kenwood

Kenwood Excelon CA-GRL98RG Instrukcja

25 Września 2024
Kenwood

Kenwood Excelon CA-PLT98 Instrukcja

25 Września 2024
Kenwood

Kenwood Excelon CA-PLT14SG Instrukcja

25 Września 2024
Kenwood

Kenwood Excelon CA-PLT14RG Instrukcja

25 Września 2024
Kenwood

Kenwood Excelon P-HD4UT Instrukcja

25 Września 2024
Kenwood

Kenwood Excelon CA-GRL14RG Instrukcja

25 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024