Instrukcja obsługi Kenwood DNX8120

Kenwood urządzenie GPS DNX8120

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kenwood DNX8120 (33 stron) w kategorii urządzenie GPS. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/33

DNX8120

DDX812

DDX8032BT

GPS NAVIGATION SYSTEM

MONITOR WITH DVD RECEIVER

INSTALLATION MANUAL

SYSTÈME DE NAVIGATION GPS

MONITEUR AVEC RÉCEPTEUR DVD

MANUEL D’INSTALLATION

SISTEMA DE NAVEGACIÓN GPS

MONITOR CON RECEPTOR DVD

MANUAL DE INSTALACIÓN

2 | DNX8120/DDX812/DDX8032BT

..........1

..........2

..........1

..........6

..........1

DNX8120 only ..........1

DNX8120 only

..........1

DNX8120 only

..........1

Accessories

English | 3

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following

order: ground, battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

2WARNING

• If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

• Do not cut out the fuse from the ignition wire (red) and the

battery wire (yellow). The power supply must be connected

to the wires via the fuse.

Acquiring GPS Signals

The first time you turn on the DNX8120, you must

wait while the system acquires satellite signals for

the first time. This process could take up to several

minutes. Make sure your vehicle is outdoors in an

open area away from tall buildings and trees for

fastest acquisition. After the system acquires satellites

for the first time, it will acquire satellites quickly each

time thereafter.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• Make sure to ground the unit to a negative 12V DC power

supply.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If the power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the wires or ground them to any metal -

part in the car.

• When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals (do

not mix front and rear). For example, if you connect the +

connector of the left speaker to a front output terminal, do

not connect the connector to a rear output terminal.-

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

• This unit has the cooling fan (page 5) to decrease the

internal temperature. Do not mount the unit in a place

where the cooling fan of the unit are blocked. Blocking

these openings will inhibit the cooling of the internal

temperature and result in malfunction.

• Do not press hard on the panel surface when installing the

unit to the vehicle. Otherwise scars, damage, or failure may

result.

• Reception may drop if there are metal objects near the

Bluetooth antenna.

Bluetooth antenna unit

Specyfikacje produktu

Marka:	Kenwood
Kategoria:	urządzenie GPS
Model:	DNX8120

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kenwood DNX8120, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje urządzenie GPS Kenwood

Kenwood DMX908S Instrukcja

30 Września 2024

Kenwood DNX7120 Instrukcja

30 Sierpnia 2024

Kenwood DNX8120 Instrukcja

18 Sierpnia 2024

Kenwood DNX7020EX Instrukcja

13 Sierpnia 2024

Kenwood DNX6990HD Instrukcja

8 Sierpnia 2024

Kenwood DDX896 Instrukcja

6 Sierpnia 2024

Kenwood DNX812 Instrukcja

26 Maja 2024

Instrukcje urządzenie GPS

Najnowsze instrukcje dla urządzenie GPS

Cobblestone Copenhagen Tracker Instrukcja

8 Października 2024

Uniden R3 Instrukcja

8 Października 2024

TomTom GO Camper Max (2nd Generation) Instrukcja

7 Października 2024

Trackilive TL-60 Instrukcja

7 Października 2024

Garmin GPSMAP 1242 Touch Instrukcja

7 Października 2024

GlobalSat BU-353S4 Instrukcja

5 Października 2024

PAJ GPS Easy Finder 4G Instrukcja

4 Października 2024

PAJ GPS CAR OBD Finder 2.0 4G Instrukcja

4 Października 2024

PAJ GPS Allround Finder 4G Instrukcja

4 Października 2024

PAJ GPS POWER Finder 4G Instrukcja

4 Października 2024