Instrukcja obsługi Kemppi A7 TIG Orbital System 300
Kemppi
Urządzenie spawalnicze
A7 TIG Orbital System 300
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kemppi A7 TIG Orbital System 300 (61 stron) w kategorii Urządzenie spawalnicze. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/61
300
1920390
1615
A7 TIG Orbital System
EN
OPERATING MANUAL
2A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
1.1 General ......................................................................................................4
1.2 About the product ....................................................................................5
1.3 Weld head .................................................................................................. 6
1.3.1 General specications .............................................................................6
1.4 Controller unit ...........................................................................................7
1.4.1 Remote control ......................................................................................7
1.5 Compatibility .............................................................................................8
2. Installation .............................................................................................9
2.1 Controller connections .............................................................................9
2.2 Water cooler ............................................................................................10
2.2.1 Filling water cooler with coolant ............................................................10
2.2.2 Operating the water ow .......................................................................10
2.3 Weld head set-up ....................................................................................11
2.3.1 Assemblies ..........................................................................................11
2.4 Installing guide ring on tube ..................................................................13
2.5 Mounting the weld head ........................................................................14
2.6 Wire spool ................................................................................................15
2.7 Electrode ..................................................................................................16
2.8 Torch centering .......................................................................................17
2.9 Mechanical adjustments .........................................................................17
3. Operation .............................................................................................18
3.1 Welding settings .....................................................................................18
3.1.1 Setting current level ..............................................................................18
3.1.2 Pulsillation (synchronized pulsed current/oscillation mode)..........................18
3.1.3 Filler wire speed ...................................................................................18
3.1.4 Root-pass procedure .............................................................................19
3.1.5 Hot-pass procedure ..............................................................................19
3.1.6 Fill passes, oscillation (weave), and stringer bead techniques ........................20
3.1.7 Shield gas eects ..................................................................................21
3.2 Preparing the work piece ........................................................................21
3.2.1 Groove preparation ...............................................................................21
3.2.2 Joint design and t-up tolerance ............................................................21
3.2.3 Other preparations ...............................................................................22
3.2.4 Developing weld procedures/process parameters ......................................22
3.3 Controller unit menus .............................................................................23
3.3.1 Main Menu ..........................................................................................23
3.3.2 Maintenance Menu ...............................................................................25
3.3.3 Options Menu ......................................................................................27
3.3.4 Compatible weld head models ................................................................28
3.3.5 Calibrate head .....................................................................................28
3.3.6 300-head guide ring speed factors ...........................................................29
3.3.7 Advanced Help ....................................................................................30
3.3.8 Autotack .............................................................................................30
3.3.9 Autoprogram .......................................................................................31
3.4 Alphanumeric labelling ...........................................................................33
3.5 Manual programming .............................................................................33
3.6 Prepurge – Upslope.................................................................................37
3.7 Programmed oscillation width (without striking an arc) .......................37
3.8 Editing a weld program...........................................................................38
3.9 Completing the programming ...............................................................39
3.10 Updating software ..................................................................................39
3.11 Welding ...................................................................................................39
3.12 Travel speed correction ...........................................................................39
3.13 Shielding gas ...........................................................................................40
3.13.1 Purging the pipe ID with inert gas ...........................................................41
4. Additional details ..............................................................................42
4.1 Controller technical data .........................................................................42
4.2 Weld head technical data........................................................................42
4.3 Ordering information ..............................................................................43
3A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
5. Troubleshooting ................................................................................46
5.1 Operation problems ................................................................................46
5.2 Root-pass renement for horizontal pipe (5G position) ........................47
5.3 Common weld defects: identication and prevention ..........................48
5.4 Warnings/error messages ......................................................................49
5.5 Checking machine setup during booting ..............................................53
5.6 Machine system messages......................................................................54
5.7 Controller unit fault conditions ..............................................................54
6. Maintenance .......................................................................................55
6.1 Preventing tungsten electrode rotation not concentric to tube OD .....55
6.2 Periodic maintenance .............................................................................55
6.3 Weld head maintenance .........................................................................56
6.3.1 External maintenance............................................................................56
6.3.2 Low prole kit installation ......................................................................56
6.3.3 Torch cable replacement ........................................................................56
6.3.4 Maintenance of the wire feed nozzle ........................................................56
6.3.5 Water cooler maintenance/ushing procedure for the torch cable .................57
6.3.6 Maintenance of torch components ..........................................................57
6.3.7 Cleaning the weld head .........................................................................58
6.3.8 Internal arcing .....................................................................................58
6.4 Printer operation and maintenance .......................................................59
6.4.1 Installing paper in the printer..................................................................59
6.4.2 Cleaning the printer ..............................................................................59
6.5 Service Workshop maintenance ............................................................59
7. Disposal ................................................................................................60
Specyfikacje produktu
| Marka: | Kemppi |
| Kategoria: | Urządzenie spawalnicze |
| Model: | A7 TIG Orbital System 300 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kemppi A7 TIG Orbital System 300, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Urządzenie spawalnicze Kemppi
5 Października 2024
25 Września 2024
24 Września 2024
23 Września 2024
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
19 Września 2024
Instrukcje Urządzenie spawalnicze
- Urządzenie spawalnicze GYS
- Urządzenie spawalnicze Weldkar
- Urządzenie spawalnicze Frilass
- Urządzenie spawalnicze Elektra Beckum
- Urządzenie spawalnicze DEKO
Najnowsze instrukcje dla Urządzenie spawalnicze
28 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024