Instrukcja obsługi Kemppi A7 MIG Power Source 350
Kemppi
Urządzenie spawalnicze
A7 MIG Power Source 350
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kemppi A7 MIG Power Source 350 (67 stron) w kategorii Urządzenie spawalnicze. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/67
350, 450
1920300
1824
A7 MIG WelderA7 MIG Welder
EN
OPERATING MANUAL
2A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
2. Installation .............................................................................................5
3. System Overview ................................................................................6
3.1 Power Source ............................................................................................. 6
3.2 Robot interface unit ..................................................................................7
3.3 User interfaces ........................................................................................... 8
3.4 A7 MIG Wire Feeder 25 ..............................................................................9
3.5 MIG Guns .................................................................................................11
3.6 Cooling unit .............................................................................................12
3.7 I/O device.................................................................................................13
4. Using the welder ...............................................................................14
4.1 Basic controls ...........................................................................................14
4.2 Setup panel .............................................................................................14
4.2.1 Button functions ..................................................................................15
4.2.2 Main menu ..........................................................................................16
4.2.3 Memory channel wizard ........................................................................16
4.2.4 User settings ........................................................................................22
4.2.5 Welding system settings ........................................................................22
4.2.6 System tests ........................................................................................25
4.2.7 Robot settings .....................................................................................26
4.3 Web user interface ..................................................................................29
4.3.1 Welding display....................................................................................30
4.3.2 Gas, air and wire inch ............................................................................30
4.3.3 Logbook .............................................................................................31
4.3.4 About .................................................................................................31
4.3.5 Welding settings – Memory channels .......................................................31
4.3.6 Settings – Language .............................................................................35
4.3.7 Settings – Users ....................................................................................35
4.3.8 Settings – Change PIN ...........................................................................35
4.3.9 Settings – Fieldbus................................................................................36
4.3.10 Settings – Network ...............................................................................36
4.3.11 Settings – Backup, restore and reset .........................................................37
4.3.12 Settings – Licenses ................................................................................37
4.4 User identication ...................................................................................38
4.4.1 Overview ............................................................................................38
4.4.2 Turning user identication system on .......................................................39
4.4.3 Creating new users ...............................................................................39
4.4.4 Deleting a user .....................................................................................40
4.4.5 Changing user role ...............................................................................40
4.4.6 Changing username ..............................................................................40
4.4.7 Changing PIN code ...............................................................................40
4.4.8 Resetting PIN code ...............................................................................41
4.4.9 Logging in and out, changing active user ..................................................41
4.5 Touch sensor (seam search) ....................................................................42
4.5.1 Voltage source, levels and safety .............................................................44
4.5.2 Touch tool ...........................................................................................45
4.5.3 Fast status output .................................................................................45
4.5.4 Selecting output voltage .......................................................................45
4.5.5 Conguring touch tool ..........................................................................46
4.6 Through Arc Seam Tracking (TAST) ........................................................46
4.7 Collision sensor .......................................................................................47
4.7.1 Setting collision sensor on and o ...........................................................48
4.7.2 Selecting sensor type ............................................................................48
4.7.3 Selecting output polarity .......................................................................48
4.8 Wire feeder ..............................................................................................49
4.8.1 Loading the ller wire ...........................................................................49
4.9 Arc measurement ....................................................................................53
4.9.1 Setup and calibration ............................................................................53
4.9.2 Display ...............................................................................................53
3A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.10 Gas ow sensor .......................................................................................54
4.10.1 On/O control .....................................................................................54
4.10.2 Gas ow sensing level ...........................................................................54
4.10.3 Gas mixture setup ................................................................................55
5. Troubleshooting ................................................................................56
5.1 Typical problems .....................................................................................56
5.2 Error codes ...............................................................................................57
5.2.1 Power source errors ..............................................................................57
5.2.2 Cooling unit errors ................................................................................58
5.2.3 Wire feeder errors .................................................................................59
5.2.4 Welding curve errors .............................................................................59
5.2.5 Robot interface errors............................................................................60
5.2.6 I/O device errors ...................................................................................61
6. Operation disturbances ..................................................................62
7. Maintenance .......................................................................................63
7.1 Daily maintenance ..................................................................................63
7.2 Periodic maintenance .............................................................................63
7.3 Service shop maintenance ......................................................................63
8. Disposal ................................................................................................64
9. Ordering numbers ............................................................................64
10. Technical data ....................................................................................65
Specyfikacje produktu
| Marka: | Kemppi |
| Kategoria: | Urządzenie spawalnicze |
| Model: | A7 MIG Power Source 350 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kemppi A7 MIG Power Source 350, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Urządzenie spawalnicze Kemppi
5 Października 2024
25 Września 2024
24 Września 2024
23 Września 2024
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
19 Września 2024
Instrukcje Urządzenie spawalnicze
- Urządzenie spawalnicze GYS
- Urządzenie spawalnicze Weldkar
- Urządzenie spawalnicze Frilass
- Urządzenie spawalnicze Elektra Beckum
- Urządzenie spawalnicze DEKO
Najnowsze instrukcje dla Urządzenie spawalnicze
28 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024