Instrukcja obsługi Keith MCmillen QuNeo

Keith MCmillen Sprzęt DJ-ski QuNeo

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Keith MCmillen QuNeo (4 stron) w kategorii Sprzęt DJ-ski. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Congratulations on your purchase of the Nano Q-Tron envelope-controlled

lter! An envelope-controlled lter modulates an instrument’s tone based

on the musician’s dynamics and playing style. The loudness of your instru-

ment’s signal forms a volume envelope that directly sweeps the cutoff or

center frequency of the lter. In the Nano Q-Tron, three different lter

types are available: Lowpass, Bandpass and Highpass, all controllable with

variable Q and sensitivity knobs; yielding a wide range of tonal options.

Nano Envelope Filter

Operating Instructions

Connect your guitar to the INPUT jack on the Nano Q-Tron and the AMP

jack to your amp’s input. Apply power if needed; your Nano Q-Tron might

already have a 9V battery installed. Press the footswitch to ensure the

STATUS LED is lit, now your Nano Q-Tron is ready to go.

The Nano Q-Tron’s effect is controlled by the musician’s playing dynamics.

A stronger attack or louder note will yield a more dramatic effect, while

softer playing will produce more subtle effects. Use the full range of control

settings in combination with different playing techniques to obtain several

different and unique effects combinations.

TIP: You might nd that the DRIVE and Q controls work best when they are

in the middle of their range rather than maximized.

TIP: When you play a note into the Nano Q-Tron, its lter jumps up to a

high frequency and then the frequency slowly descends according to the

volume envelope of the notes you play. The louder your note, the higher

in frequency the lter jumps.

Controls and Connections

1. DRIVE Knob Sets the envelope sensitivity gain, which in turn controls

how wide the lter sweeps. The higher the DRIVE setting, the more the

lter reacts to your playing and the higher in frequency the lter will jump

when you play a note. Turn DRIVE clockwise for a wider lter sweep or

counterclockwise to reduce the sweep range. If you turn DRIVE up too far,

the lter sweep will max out at its highest frequency (approximately 3.5kHz)

and remain at the highest frequency until the note has fully decayed.

Louder instruments will typically use lower DRIVE settings while quieter

instruments require higher settings. When learning the Nano Q-Tron,

start with DRIVE at 12 o’clock.

- 2 -

- 3 -

2. MODE Rotary Switch (LP / BP / HP) Determines the frequency range

that the lter allows to pass through. LP (Lowpass) mode emphasizes low

frequencies, BP (Bandpass) middle frequencies and HP (Highpass) high

frequencies.

3. Q Knob Sets the bandwidth of the lter. As Q is turned clockwise, the

lter sounds more resonant or peakier, making the envelope effect more

dramatic. Low settings of Q yield a less intense lter curve. Start with Q

set to about 2 o’clock for a middle-of-the-road lter intensity.

4. VOL Knob Adjusts the overall volume at the OUTPUT jack. As VOL is

turned clockwise, the output level increases. Use VOL to match the effect

volume to your bypass volume or give the effect a volume boost.

5. FOOTSWITCH and STATUS LED The footswitch engages or bypasses the

effect. The Status LED lights when the effect is engaged. The LED is off in

bypass mode. The Nano Q-Tron employs True Bypass.

6. INPUT Jack Audio input to the Nano Q-Tron.

7. AMP Jack Audio output from the Nano Q-Tron. In bypass mode, the AMP

jack is directly connected to the INPUT jack.

8. 9V Power Jack An optional 9VDC, center-negative power supply can be

connected to the power jack to provide power without a battery. The Nano

Q-Tron requires 10mA at 9VDC on a center-negative plug. Do not exceed

12VDC at the power jack.

When using a 9V battery, plugging into the INPUT jack activates power.

The input cable should be removed when the unit is not in use to avoid

running down the battery.

To change the 9-volt battery, you must remove the 4 screws on the bottom

of the Nano Q-Tron. Once the screws are removed, you can take off the

bottom plate and change the battery. Please do not touch the circuit board

or adjust the trim pot while the bottom plate is off or you may damage a

component or set the lter sweep range to a non-ideal setting.

Notes and Specications

t Audio input impedance at INPUT jack: 330kΩ

t Audio output impedance at OUTPUT jack: 300Ω

t Current draw: 10mA

t Maximum input signal level: +5.2dBu

Specyfikacje produktu

Marka:	Keith MCmillen
Kategoria:	Sprzęt DJ-ski
Model:	QuNeo

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Keith MCmillen QuNeo, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt DJ-ski Keith MCmillen

Keith MCmillen QuNeo Instrukcja

15 Sierpnia 2024

Instrukcje Sprzęt DJ-ski

Najnowsze instrukcje dla Sprzęt DJ-ski

Line 6 Helix Control Instrukcja

11 Stycznia 2025

AlphaTheta DDJ-GRV6 Instrukcja

8 Stycznia 2025

Glorious Record Box 55 Instrukcja

4 Stycznia 2025

Glorious Record Box Display Door Instrukcja

4 Stycznia 2025

Glorious Session Cube XL Instrukcja

4 Stycznia 2025

Glorious Modular Mix Station Instrukcja

4 Stycznia 2025

Glorious Record Box Advanced 110 Instrukcja

4 Stycznia 2025

Glorious Mix Station 2 Instrukcja

4 Stycznia 2025

Glorious CD Box 90 Instrukcja

4 Stycznia 2025

Glorious Record Box 230 Instrukcja

4 Stycznia 2025