Instrukcja obsługi K&K Sound Definity System

K&K Sound Niesklasyfikowane Definity System

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla K&K Sound Definity System (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541-888-3517 | Toll Free 1-800-867-6863 | www.kksound.com
D E F IN I T Y S Y S T E M
GENERAL PICKUP INFORMATION
The Definity pickup is a hybrid of a compression
pickup and a soundboard transducer. Its super-thin
and flexible design allows for a variety of
applications especially on instruments with floating
bridges.
The Definity System is paired with the Definity
Preamp, which is optimized for the Definity pickup
and a very important part of the system. The Definity
Preamp features a phase switch, which is particularly
important for this pickup. Please see p. 3 for more
information on the phase switch.
We found the Definity System performs best when
the pickup is installed so that part of it is under
pressure by the floating bridge and part of it is “free
floating” to pick up vibrations like a sound board
pickup.
It is not necessary for the Definity pickup to cover the
entire area of a bridge or bridge foot. As a general
rule, you want to aim for a placement that allows
approximately half of the pickup under a bridge
(compression) and the other half free on the
soundboard. There are some exceptions for
instruments with narrow bridges, like banjos. (More
detailed information on this on p. 4.) But it is a good
strategy for Archtop or Maccaferri/Selmer guitars
and many other floating bridge instruments.
This manual will describe installation techniques and
locations that we have tested to deliver the best
results for a variety of popular floating bridge
instruments.
GENERAL INSTALLATION PROCEDURE
1. Mark the position of the bridge on the
soundboard with tape. Make sure the tape
will not interfere with the position of the
Definity pickup. Then loosen the strings and
move the bridge out of the way to allow
mounting the pickup.
2. Install the Definity pickup so that the bridge
stands on its front portion and the back half
(where the cable exits) sticks on the
soundboard, similar to how it is shown on
one of the photos below.
3. Remove the red release foil on the bottom of
the pickup and stick the transducer in place.
4. Move the bridge back into position and
secure the gray cable of the pickup with tape
so it does not cause noise.
2
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541-888-3517 | Toll Free 1-800-867-6863 | www.kksound.com
5. The jack can be mounted at a convenient spot
near the endpin of the instrument.
6. Coil up extra cable and secure it, e.g. with
clear tape.
OUTPUT JACK
The Definity pickup comes with a Switchcraft stereo
endpin jack wired in mono. It has a self-adhesive
removable clip attached to it. This jack also allows
for internal mount when the clip is removed. If go
this route, it may require you to temporarily unsolder
the pickup during installation. Please consult a
skilled technician if you choose this option.
Too remove the clip please use a slot screwdriver to
open the snap tab (see photo). Then remove the
black electrical tape that is wound around the jack.
This tape only builds up the diameter of the jack to
match the clip.
INTERNAL JACK INSTALLATION
1. For internal mount only, skip this section if
you are using the clip.
2. Drill or widen the endpin hole to 1/2" using
protective tape to cover the area around the
hole. This helps to prevent chips and
scratches.
3. Unscrew the endpin jack's strap mount knob.
4. Take off the nut and washer.
5. Find out the thickness of your end block and
set the nut on the cap accordingly (see
picture below). Once in place, screw the cap
in as far as it goes.
6. Insert the jack from the inside into the endpin
hole. Tip: a chopstick or something similar
helps to get a hold of the jack and pull it
through the hole.
7. Attach outside washer and nut and tighten.
Use a small Allen wrench or similar in the
small front holes of the jack to hold on while
tightening the nut. Attach the end knob and
tighten by hand.
Important: Make sure that the strap knob screws in
ALL THE WAY over the outer threaded part of the
jack, so that a tiny portion of the thread is exposed
when the strap-knob is tightened. If you don’t do this,
you might experience insufficient signal transmission
and sound cutting in and out.
THE DEFINITY PREAMP
Open the lid of the box (it just pulls off – it snaps back
on) to get access to the battery compartment and to
the adjustment options inside the preamp.
Install a 9-volt battery in the battery compartment.
There are midrange and treble trim-potentiometers
(trim-pots) that can be adjusted with a small
screwdriver. When the little white arrow in the center
of the trimmer is in the 12 o’ clock position, the
setting is flat with no cut or boost. Turning the pots
counterclockwise cuts frequencies, and turning
clockwise boosts frequencies. Mids are centered at
1250Hz (X- -wide band Q) and treble are at 8000Hz
(high shelf).
On the battery side of the circuit board is a phase
(toggle) switch with a small white tab. It has a big
effect on feedback control and on overall tone. There
is a detailed description of the effect on the phase
setting below. Move the white tab left or right (2
positions) and listen. There will be one setting that
sounds better with less feedback.
3
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541-888-3517 | Toll Free 1-800-867-6863 | www.kksound.com
CONNECTION TO AMPLIFIER
Use a regular guitar cable (not supplied) to connect
the output-jack of the pickup with the input of the
preamp. Connect the output of the preamp to an
amplifier with a regular mono guitar cord. Please
note that a stereo cable will NOT switch on the
preamp.
USING THE PHASE SWITCH
The Definity Preamp has a miniature phase switch
mounted on the battery side of the circuit board. It is
a sliding switch (a small white tab) that you can slide
to the left and right with your finger or with a small
screwdriver. There are only two settings.
The Pure XLR Preamp has a push-release phase
switch on the back.
Phase switches are usually marketed as a feedback
controlling device, but they accomplish more than
just that. A phase switch inverts the amplified sound
wave so that it does not interfere with the original,
un-amplified sound coming from your instrument.
Every acoustic instrument projects sound waves into
the air at a certain phase when it is played
unplugged. For optimal sound amplification, the
phase that is projected from the amplified speaker
source needs to be "in phase" with the acoustic
instrument's own acoustically generated sound
waves.
The problem is that amplification systems, effect
units, or any electronic audio device may or may not
invert the phase of the incoming signal. The
manufacturers do not specify. An out-of-phase
problem is indicated by early feedback and
somewhat tinny, unbalanced sound. This may be
tolerable in some tone ranges and quite noticeable
in others, even resulting in sound cancellations on
some notes.
By toggling the phase switch back and forth on the
Definity Preamp or pushing/releasing it on the Pure
XLR Preamp, you will notice fuller, warmer, and
nicely balanced tone with less feedback in one
setting. This is the correct phase switch setting. Keep
in mind that it may be different with different
amplification systems.
DEFINITY PRO WITH PURE XLR PREAMP
The Pure XLR Preamp operates on 12–48 volt
Phantom Power or 9-volt battery. The LED light on
the front-panel indicates if phantom power is present.
In order to save battery life it will not light when the
unit is running on battery power.
With phantom power, the battery will not be drained
as long as the phantom power provides more than
10 volt.
FRONT:
BACK:
CHANGING THE BATTERY
To insert and change the battery, open the 2 screws
on the sides of the unit, remove the lid, connect a
new 9-volt battery to the battery clip and place it in
the marked compartment.
The unit is delivered without a battery.
UNPLUG THE INPUT CABLE IN ORDER TO SWITCH
OFF THE BATTERY!
ADJUSTABLE GAIN CONTROL
Gain and volume both have an effect on the output
volume of the preamp, but they accomplish different
tasks.
The gain (also called input gain or sensitivity control)
is located at the INPUT of the circuit. It sets the
amount of pre-amplification before the signal enters
the EQ section, DI etc. The volume control is located
at the OUTPUT (the very end of the circuit) and
simply allows you to adjust the volume.

Specyfikacje produktu

Marka: K&K Sound
Kategoria: Niesklasyfikowane
Model: Definity System

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z K&K Sound Definity System, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane K&K Sound

K&K Sound

K&K Sound Trinity Pro Preamp Instrukcja

1 Października 2024
K&K Sound

K&K Sound Mandolin Twin Fusion Instrukcja

1 Października 2024
K&K Sound

K&K Sound Definity System Instrukcja

1 Października 2024
K&K Sound

K&K Sound Big Twin Instrukcja

1 Października 2024
K&K Sound

K&K Sound Bass Master Rockabilly Plus Instrukcja

1 Października 2024
K&K Sound

K&K Sound Pure Mini Instrukcja

1 Października 2024
K&K Sound

K&K Sound Pure Preamp Instrukcja

1 Października 2024
K&K Sound

K&K Sound Dual-Channel Pro Preamp Instrukcja

1 Października 2024
K&K Sound

K&K Sound Twin Spot Internal Instrukcja

1 Października 2024
K&K Sound

K&K Sound Volume Control Instrukcja

1 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024