Instrukcja obsługi JVC KV-CM30

JVC nieskategoryzowany KV-CM30

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JVC KV-CM30 (46 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/46

KV-CM30

UNIVERSAL REAR VIEW CAMERA

INSTRUCTION MANUAL

CAMÉRA DE RECUL UNIVERSELLE

MODE D’EMPLOI

UNIVERSAL RÜCKFAHRKAMERA

BEDIENUNGSANLEITUNG

UNIVERSELE ACHTERUITRIJCAMERA

GEBRUIKSAANWIJZING

TELECAMERA PER RETROMARCIA UNIVERSALE

ISTRUZIONI PER L’USO

CÁMARA DE VISTA TRASERA UNIVERSAL

MANUAL DE INSTRUCCIONES

CÂMARA TRASEIRA UNIVERSAL

MANUAL DE INSTRUÇÕES

B5A-1709-00 b (W)

2 |

ENGLISH

• Before nally installing the unit, connect the wiring

temporarily, making sure it is all connected up properly,

and the unit and the system work.

• When mounting this unit, make sure none of the leads are

trapped between this unit and the surrounding metalwork

or ttings.

• Do not mount this unit near the heater outlet, where

it would be aected by heat, or near the doors, where

rainwater might splash onto it. (Never install in locations

such as the above because of the danger of malfunction

due to high temperatures.)

• Before drilling any mounting holes always check behind

where you want to drill the holes. Do not drill into the gas

line, brake line, electrical wiring or other important parts.

• If this unit is installed in the passenger compartment,

anchor it securely so it does not break free while the car is

moving, and cause injury or an accident.

• If this unit is installed under a front seat, make sure it does

not obstruct seat movement. Route all leads and cords

carefully around the sliding mechanism so they do not get

caught or pinched in the mechanism and cause a short

circuit.

Care and maintenance

• When the product gets dirty, wipe dry with a silicon cloth

or soft cloth. If it is seriously stained, remove stain with

a cloth moistened with a neutral cleaner and then wipe

the cleaner away. Do not use a hard cloth and/or a volatile

substance such as lacquer thinner or alcohol, scratches,

deformation, degradation and/or damage may result.

• When a lens component gets dirty, wipe gently with a soft

cloth moistened with water. Do not rub with a dry cloth to

prevent scratching the lens.

Installation Procedure

1 To prevent a short circuit, remove the key from the

ignition and disconnect the battery.-

2 Make the proper input and output wire connections

for each unit.

3 Connect the wiring harness wires in the following

order: ground, ignition and camera unit.

4 Install the unit in your car.

5 Reconnect the battery.-

WARNING

To prevent injury or fire, take the following

precautions:

• To prevent a short circuit, never put or leave any metallic

objects (such as coins or metal tools) inside the unit.

• Installation and wiring of this product require specialist

skill and experience. To assure your safety, please request a

specialist technician to install the unit.

• When you make a hole to install the camera, check the

location of pipes, tanks and wiring and avoid touching

them. Otherwise it may cause the re.

• When you make a hole with a drill, use goggles to protect

your eyes.

CAUTION

To prevent damage to the product, take the

following precautions:

• Make sure to ground the unit to a negative 12V DC power

supply.

• When replacing a fuse, only use a new fuse with the

prescribed rating. Using a fuse with the wrong rating may

cause your unit to malfunction.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

NOTE

• A rear view camera is a camera that provides symmetrical

images in the same way as rear and side view mirrors.

• Connection to a TV with an RCA video input is possible,

but conrm whether the TV you use has a reverse gear

connection function.

• This product is designed to supplement the driver’s rear

view, but the camera images do not show all dangers and

obstacles. Be sure to look behind you when reversing to

conrm the view.

• This product features a wide-angle lens, so the near view

is wide and the far view is narrow, which may create a

false sense of distance. Be sure to look behind you when

reversing to conrm the view.

• Do not wash your car with an automatic car wash or

high-pressure water as it may result in water entering the

camera or the camera falling o.

• Check camera bracket installation before driving.

Are the screws loose?

- Is the camera bracket rmly secured?

- If the rear view camera comes loose while you are driving it

may cause an accident.

Before Use/ Installation Procedure

ENGLISH

| 3

• Lay the cords by avoiding high-temperature areas. Use

corrugated tubes for wiring inside the engine room. If a

cord contacts a high-temperature area of the vehicle, the

coating may melt and cause short-circuiting, which may

lead to a re or electric shock hazard.

Accessories

WARNING

• If you connect the ignition wire (Red) to the car chassis

(Ground), you may cause a short circuit, that in turn may

start a re. Always connect those wires to the power source

running through the fuse box.

• Do not cut out the fuse from the ignition wire (Red). The

power supply must be connected to the wires via the fuse.

CAUTION

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and o with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may be drained or aected.

• If the fuse blows, rst make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Install so that it does not obstruct the rear eld of view.

• Install so that it does not protrude from the side of the car.

• Do not perform installation in rain or fog.

• When humidity is high, dry the surface to which the unit is

to be attached before installing.

• Moisture on the attachment surface reduces adhesive

strength, which may lead to the unit coming o.

• Do not attach the camera bracket to areas on the car body

treated with uorocarbon resin, or glass.

• May result in the rear view camera falling o.

- Do not apply water to the unit.

- Do not expose the unit to rain.

- Do not subject the camera to unnecessary force.

- Thoroughly clean where tape is used for sticking on the

unit.

• Refer to the instruction manual for details on connecting to

the other brand's units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape.

To protect the wiring, wrap adhesive tape around them

where they lie against metal parts.

• Route and secure all wiring so it cannot touch any moving

parts, such as the gear shift, handbrake and seat rails.

• Do not route wiring in places that get hot, such as near the

heater outlet. If the insulation of the wiring melts or gets

torn, there is a danger of the wiring short-circuiting to the

vehicle body.

• When replacing the fuse, be sure to use only fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA cable as far away from each other

as possible.

Grommet..........1

Camera bracket clamping screw..........1

Camera [with camera bracket ] ..........1

Fuse ..........1

Specyfikacje produktu

Marka:	JVC
Kategoria:	nieskategoryzowany
Model:	KV-CM30

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JVC KV-CM30, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje nieskategoryzowany JVC

JVC KV-CM30 Instrukcja

27 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024

Emko EZM-9920 Instrukcja

27 Października 2024

Emko ESM-3712-H Instrukcja

27 Października 2024

Emko ATS-10 Instrukcja

27 Października 2024

Emko EAOM-11.2 Instrukcja

27 Października 2024

Emko EPM-3790 Instrukcja

27 Października 2024

Emko EPM-7790 Instrukcja

27 Października 2024

Livarno Lux IAN 108340 Instrukcja

27 Października 2024

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024