Instrukcja obsługi JUNG WS10KS
JUNG
transduktor
WS10KS
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JUNG WS10KS (7 stron) w kategorii transduktor. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7
KNX Combination sensor
Ref.-no.: WS 10 KS, WS 10 KS DCF
Operating Instructions
Combination sensor
1. Safety warnings
Attention:
Electrical equipment must be installed and fitted by qualified
electricians only and in strict observance of the relevant accident
prevention regulations. Failure to observe any of the installation
instructions may result in fire and other hazards.
2. Function
• The combination sensor can measure wind speed, precipitation
brightness and twilight. Brightness can be measured separately for
the cardinal points East, South and West.
• The combination sensor can be directly connected to a weather
station (e.g. Art. no. 2224 REG W) which ensures further
processing of th measured data and transmission to the bus in the
form of switching or value telegrams. Bus subscribers as, for
instance, the Info-Display ..2041.., the „Facility-Pilot“ visualization
software and the LCD annunciator and control panel MT 701 can
thus intervene into control processes, generate messages, or
control weather-dependent processes. Resulting applications are in
building services management control engineering, greenhouse
control, or in further processing of the collected data in control and
operating units.
• The combination sensor Art. no. WS 10 KSDCF is equipped with
DCF77 receiver which can receive the legal German time and
transmit the signals to the KNX/EIB bus (e.g. to synchronize
KNX/EIB clocks).
• To ensure trouble-free service even in case of frost, the
combination sensor can be heated.
• The combination sensor needs an external 24 V power supply, Art.
no. WSSV10.
Stand: Mai-07 325 552 23
KNX Combination sensor
Ref.-no.: WS 10 KS, WS 10 KS DCF
3. Installation
Important: Combination sensor with DCF77
Check the place of installation for optimal reception of the DCF77 time
signal. Reflexions can cause reception interference. If no interference-
free reception is possible, change the place of installation by a few
meters until the combination sensor receives the time signal without
interference (see chapter „Antenna orientation“).
• For installation on a tubular mast (Ø 35 ... 50 mm), a stainless-steel
mounting bracket is supplied with the sensor (FIG.(1) .
• The combination sensor must be installed unobstructed by
obstacles in all directions.
• When the combination sensor is installed in front of a wall, a
minimum spacing of 0.5 m must be respected to prevent incorrect
measuring values due to negative influence on the sensors.
• To enable the brightness sensors to clearly determine the sun’s
actual position, the combination sensor must be aligned with the
help of a compass in such a way that the precipitation window
points to the North (see FIG. 2). In this case, the brightness sensors
are correctly aligned with the cardinal points (FIG.3).
• To ensure perfect wind speed measurements, the wind wheel must
be able to turn freely. This can be checked visually at low wind
speeds.
2
KNX Combination sensor
Ref.-no.: WS 10 KS, WS 10 KS DCF
• To ensure perfect wind speed measurements, the wind wheel must
be able to turn freely. This can be checked visually at low wind
speeds.
• The part of the enclosure where the brightness and precipitation
sensors are located (side and top of the device) should be free from
dust deposits to avoid incorrect measuring values. In operation,
rainfall is mostly sufficient to clean the enclosure surfaces.
3.1. Connection
• The combination sensor is provided with a 10 m-long connecting
cable. The cable may be extended up to 50 m max. (recommended
cable: LiYCY 6 x 0.25 mm2, shielded).
Connect the combination sensor to the weather station (FIG. 4):
(a) pink : supply AC/DC 24 V, 600 mA
(b) grey : supply ground
(c) green-yellow : shield
(1) green : system voltage DC 24 V, > 15 mA
(2) yellow : data
(3) white : sync.
(4) brown : system ground
3
Specyfikacje produktu
| Marka: | JUNG |
| Kategoria: | transduktor |
| Model: | WS10KS |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z JUNG WS10KS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje transduktor JUNG
10 Grudnia 2024
10 Grudnia 2024
10 Grudnia 2024
10 Grudnia 2024
Instrukcje transduktor
Najnowsze instrukcje dla transduktor
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
7 Grudnia 2024
7 Grudnia 2024
7 Grudnia 2024
7 Grudnia 2024