Instrukcja obsługi Joy-It SEN-KY033LT


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Joy-It SEN-KY033LT (7 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
www.joy it.net-
Pascalstr. 8 47506 Neukirchen Vluyn-
LINE TRA
LINE TRA
LINE TRA
LINE TRALINE TRACKER
CKER
CKER
CKERCKER
SEN KY033LT-
1. GENERAL INFORMATION
1. GENERAL INFORMATION
1. GENERAL INFORMATION
1. GENERAL INFORMATION1. GENERAL INFORMATION
Dear costumer,
thank you very much for choosing our product.
In following, we will introduce you to what to observe while starting up
and using this product.
Should you encounter any unexpected problems during use, please do
not hesitate to contact us
www.joy it.net-
Pascalstr. 8 47506 Neukirchen Vluyn-
2. PIN ASSIGNMENT
2. PIN ASSIGNMENT
2. PIN ASSIGNMENT
2. PIN ASSIGNMENT2. PIN ASSIGNMENT
1. Connection
3. USAGE WITH A RASPBERRY PI
3. USAGE WITH A RASPBERRY PI
3. USAGE WITH A RASPBERRY PI
3. USAGE WITH A RASPBERRY PI3. USAGE WITH A RASPBERRY PI
KY033
KY033
KY033
KY033KY033 Raspberry Pi
Raspberry Pi
Raspberry Pi
Raspberry PiRaspberry Pi
GND Ground
(Pin 6)
V+ 3,3 V
(Pin 1)
Signal GPIO24
(Pin 18)
www.joy it.net-
Pascalstr. 8 47506 Neukirchen Vluyn-
2. Code example
This sample code shows in the console whether the sensor is above a line
or not. This is done by infrared, because if the sensor is on the line, the
transmitted infrared signal does not reach the receiver.
# Required modules are imported and set up
import as RPi.GPIO GPIO
import time
GPIO.setmode(GPIO.BCM)
# The input pin to which the sensor is connected, is declared here.
GPIO_PIN = 24
GPIO.setup(GPIO_PIN, GPIO.IN, pull_up_down = GPIO.PUD_UP)
# Pause between the output of the result is defined (in seconds)
delayTime = 0.5
print ("Sensor Test [druecken Sie STRG+C, um den Test zu beenden]")-
# Main loop of the program
try:
while True:
if GPIO.input(GPIO_PIN) == True:
print ("LineTracker is above the line")
else:
print ("LineTracker is out of a line")
print (" ")---------------------------------------
# Reset + Delay
time.sleep(delayTime)
# Clean up after the program has finished
except KeyboardInterrupt:
GPIO.cleanup()
You can also download this sample code .
here
here
here
herehere
Furthermore, the sensor has a potentiometer with which the
sensitivity can be adjusted. A LED also lights up when the sensor receives
an infrared signal, i.e. leaves the line.
But first you have to install this package:
sudo apt install python3 rpi.gpio-
Now, you can either use the following commands to download and unzip
the file :
wget http://sensorkit.joy- - it.net/images/c/cf/KY 033_RPi_Trackingsensor.zip
unzip KY-033_RPi_Trackingsensor.zip


Specyfikacje produktu

Marka: Joy-It
Kategoria: Niesklasyfikowane
Model: SEN-KY033LT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Joy-It SEN-KY033LT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Joy-It

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025