Instrukcja obsługi JL Audio PS-SWMCP

JL Audio głośnik PS-SWMCP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio PS-SWMCP (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Installation Instructions for all
PS-SWMCP
swivel fixtures for round pipes
P I PE M O UN T I N G FIX T URE S ( S W I V EL)
FOR PS650VeX™ ENCLOSED SPEAKER SYSTEMS
NOTE: The PS-SWMCP-B-2.000 Fixture and PS650-VeX-SG-TMB Enclosed Speaker
System are used in this manual for illustrative purposes only. The fixture installation
steps are the same for all PS650-VeX Enclosed Speaker Systems and all PS-SWMCP
swivel fixtures for round pipes.
LIMITED WARRANTY  MARINE PRODUCTS USA
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the
original date of purchase.
This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service
be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),
repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not
covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages
and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning
with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For Service Information in the U.S.A. please call
JL Audio Customer Service: (954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025, USA
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and n ot by JL Audio, Inc.
w w w . j l a u d i o . c o m
JL Audi o® and the JL Audi o logo are re gistered t rademar ks of JL Audi o, Inc. “Ahead of t he Curve” an d its respe ctive lo go is a trade mark of JL Audi o, Inc.
©2016 JLAudio, Inc. • For more det ailed inf ormation please visit us online at w ww.jlaudio.com. Due to o ur policy of continuo us produc t develop ment, all sp ecifications are su bject to ch ange witho ut notice.
SKU# 011498
Printed in U.S.A. • 092817
Mounting Fixture is made in the USA by Axia Alloys
Protected by US Patents #8,136,771 & #8,398,035
Included Hardware: BOM ID Quantity Description
1 4 Axia Alloys Strap Clamp
2 6 M6 x 16 mm Socket Cap Machine Screw
3 2 M4 x 4 mm Set Screw (pre-installed)
4 4 M6 Nylon Insert Locknut
5 2 Clamp Receiver
6 1 Loctite® Red read-Locking Compound
7 4 M6 Flat Washer
8 4 M6 x 45 mm Socket Cap Machine Screw
9 1 Plastic Strip
10* 2 Fixture Base
11* 1 Silicone Adhesive
12* 12 #8 Flat Washer
13* 12 #8 x 1-1/4” Pan Head Screw
* Included with VeX™ speaker enclosures.
(hardware pictured for one)
Note: Not all wires may be used in normal applications.
Wire Size Wire Color Use
16 AWG Red/Stripe Speaker Positive (+)
Black/Stripe Speaker Negative (–)
20 AWG
Red Not Used
Green Not Used
Blue LED Positive (+)
Yellow LED Negative (–)
Wire Size Wire Label Use
16 AWG “ ”+Speaker Positive (+)
N/A Speaker Negative (–)
For Premium Models:
For Standard Models:
Loosen the pre-installed M4 x 4 mm Set Screw in the
clamp receiver. Slide an M6 x 16 mm Machine Screw
through the center hole of the clamp receiver, into the
center hole in the xture base, and hand tighten.
1
If you wish to rotate the speaker’s grille/logo badge
alignment, remove the six #8 x 1-1/4” speaker mounting
screws and #8 Flat Washers.
9
Apply Loctite® red thread-locking compound to two M6
x 16 mm Machine Screws, slide them through the slots
in the clamp receiver, into the appropriate holes in the
xture base, and fully tighten.
5
Secure the clamps to the clamp receiver using a pair of
M6 x 45 mm Machine Screws, M6 Flat Washers, and M6
Locknuts as illustrated. e locknut should be installed
into the hex shaped recess on one end of each clamp.
Hand-tighten, allowing just enough freedom to rotate the
enclosure around the pipe.
3
Realign the clamps with the clamp receiver on the
enclosure, and secure them to the clamp receiver using a
pair of M6 x 45 mm Machine Screws, M6 Flat Washers,
and M6 Locknuts as illustrated, and fully tighten. Note:
e locknut should be installed into the hex shaped
recess on one end of each clamp.
7
Place the supplied plastic strip around the pipe to
prevent scratching. Push the clamps over the pipe
(remove the plastic strip). Align the clamps with the
clamp receiver on the enclosure.
2
Remove the center M6 x 16 mm Machine Screw from the
clamp receiver, apply Loctite® red thread-locking
compound, reinstall, and fully tighten.
6
Position the enclosure at the desired location, tightening
the M6 x 45 mm Machine Screws as necessary. Fully
tighten the pre-installed M4 x 4 mm Set Screw in the
clamp receiver to hold its position. Mark the location
of the clamps on the pipe, then remove the enclosure
from the pipe.
4
Rotate the speaker to the desired angle. Reinstall the
speaker and speaker mounting screws and washers.
Hand-tighten in a criss-cross pattern.
10
Remove adhesive backing and install the JL Audio logo
badge.
8
Remove the backing from the rear logo appliqué. With
the logo positioned at the desired angle, attach the
appliqué to the back of the enclosure.
11
Gently press on the appliqué from the center out to
remove any air pockets.
12
Clean the inside of the aluminum cap with acetone (not
included) prior to attaching it to the enclosure. Apply a
circular bead of silicone adhesive to the inside of the
aluminum logo cap, 1/2-inch (13 mm) from the outer edge.
13
Align the aluminum logo cap to the desired angle of
rotation, and press it onto the back of the enclosure.
Apply masking tape (not included) to hold the cap in
place until the silicone cures (at least 24 hours).
14
• For marine installations, do not connect the speaker’s LED lights to the vessel’s navigational lighting circuits.
• For short-circuit protection, install a supplied fuseholder onto EACH speaker’s BLUE (+12V) LED power connection lead.
• Connect all BLUE (+12V) leads together (parallel) and connect to a switched +12V supply. Connect all YELLOW (GND)
leads together and connect to a negative ground or to the NEGATIVE battery post.
• We recommend activating the speakers’ LEDs thru a lighting circuit that supplies +12V via an existing switch. If an
existing switched circuit is not available, you may install a dedicated toggle/rocker style switch that will supply positive
(+12V) power. Fuse this connection according to how many LED circuits you have (LED circuits x 150 mA).
[ D]GN
LED
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
Fuse
Fuse
Fuse
Example: One speaker pair of
LED circuits connected in parallel.
Steps 11-12 are for Standard Models Only
Steps 13-14 are for Premium Models Only

Specyfikacje produktu

Marka: JL Audio
Kategoria: głośnik
Model: PS-SWMCP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio PS-SWMCP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik JL Audio

JL Audio

JL Audio C6-100ct Instrukcja

4 Października 2024
JL Audio

JL Audio C6-650 Instrukcja

4 Października 2024
JL Audio

JL Audio CF-350mt Instrukcja

4 Października 2024
JL Audio

JL Audio C6-650cw Instrukcja

4 Października 2024
JL Audio

JL Audio SA-TPOD-100-BK Instrukcja

29 Września 2024
JL Audio

JL Audio C5-525x Instrukcja

20 Września 2024
JL Audio

JL Audio C5-570 Instrukcja

18 Września 2024
JL Audio

JL Audio M3-770X Instrukcja

16 Września 2024
JL Audio

JL Audio C1-690 Instrukcja

14 Września 2024
JL Audio

JL Audio Evolution C2-570x Instrukcja

14 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025
Hifonics

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025
Pyle

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025
ION

ION Insta Sound Instrukcja

15 Stycznia 2025
Pure Acoustics

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025
Polk

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025
Sennheiser

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025