Instrukcja obsługi JL Audio M6-880X

JL Audio głośnik M6-880X

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio M6-880X (8 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

OWNER’S MANUAL

Marine Coaxial Loudspeakers with

Transflective™ RGB LED Lighting (optional)

Thank you for purchasing a JL Audio Marine Coaxial Speaker System.

With proper installation, your new speakers will deliver

years of listening pleasure.

We strongly recommend that you have your new marine speakers

installed by your authorized JL Audio dealer.

The installation professionals employed by your dealer have

the necessary tools and experience to properly install your new speakers.

If you prefer to perform your own installation,

please read this instruction manual completely before

beginning the process.

2 | JL Audio - M6-650X / M6-770X / M7-880X Owner’s Manual

Built in USA with glob al components.

Patents pending.

MA RINE COA XIA L

AB E

Physical Specifications M6-650X M6-770X M6-880X

Nominal Diameter 6.50 in. / 165 mm 7.70 in. / 196 mm 8.80 in. / 224 mm

Outer Diameter (A) 6.90 in. / 175 mm 7.70 in. / 196 mm 8.80 in. / 224 mm

Bolt Hole Circle (B) 6.13 in. / 156 mm 6.92 in. / 176 mm 7.97 in. / 202 mm

Frontal Grille Protrusion-Classic* (C) 0.94 in. / 24 mm 1.03 in. / 26 mm 1.37 in. / 35 mm

Frontal Grille Protrusion-Sport* (C) 1.02 in. / 26 mm 1.08 in. / 27 mm 1.45 in. / 37 mm

Mounting Hole Diameter (D) 5.00 - 5.25 in. / 127 - 133 mm 6.25 in. / 159 7.375 in. / 187 mm mm

Mounting Depth (E) 3.00 in. / 76 mm 3.32 in. / 84 mm 5.00 in. / 127 mm

* Frontal grille protrusion measured from mounting surface (Sport Grille pictured)

Specifications M6-650X M6-770X M6-880X

Mounting Application Infinite Baffle Infinite Baffle Infinite Baffle

Continuous Power Handling

(RMS Method) 75 Watts / channel 100 Watts / channel 125 Watts / channel

Recommended Amplifier Power 25 - 150 Watts / channel 40 - 200 Watts / channel 50 - 250 Watts / channel

Frequency Response 55 Hz - 25 KHz (± 3 dB) 45 Hz - 25 KHz (± 3 dB) 38 Hz - 20 KHz (± 3 dB)

Efficiency @ 1W/1m 89.5 dB 91.0 dB 90.5 dB

Nominal Impedance 4 ohms 4 ohms 4 ohms

MARINE SPEAKER SPECIFICATIONS

Woofers: Injection-molded, mica-filled polypropylene

cone bodies with UV inhibitors, 1.00-inch (25 mm) voice

coils on M6-650X, 1.25-inch (32 mm) voice coils on

M6-770X and 1.40-inch (36 mm) voice coils on M6-880X,

low-profile/ progressive-roll spiders and synthetic

rubber surrounds. DMA-optimized, long excursion

design for enhanced output and bass response.

UV-resistant polymer baskets and grilles. LED equipped

models include integrated LED lighting system.

Due to ongoing product development, all specifications are subject to change without notice.

Tweeters: 0.80-inch (20 mm) on M6-650X, 1.00-inch

(25 mm) on M6-770X, 1.25-inch (32 mm) on M6-880X,

treated silk dome design, neodymium magnet, ferrofluid

cooled and damped.

Crossover Networks: True 2-way networks with 1st

order low-pass and 2nd order high-pass circuits on

M6-650X, 2nd order low-pass and 3rd order high-pass

circuits on M6-770X & M6-880X. Solid-state tweeter

protection circuit.

Included Components and Parts:

• Two Marine Coaxial Loudspeakers

• Two Polymer Woofer Grilles

• Two Polymer Woofer Trim Rings

• Two Treated Silk Dome Tweeters (Classic - mounted to

grilles / Sport - mounted to bridge)

• Two 2-way crossovers (integrated to woofer baskets)

• Twelve #8 x 1 1/8-inch (29 mm) phillips-head stainless-

steel screws for speaker mounting (M6-650X & M6-770X)

• Twelve #8 x 1 1/2-inch (38 mm) phillips-head stainless-

steel screws for speaker mounting (M6-880X)

• Twelve #8 stainless-steel washers for speaker mounting

• Mounting Template

LED Equipped Models: Integrated Transflective™ RGB

LED lighting system (patent-pending) delivers smooth,

even accent illumination, with no hot spots. LED

functionality requires separate wiring at each speaker

location. Adjustable control of RGB lighting requires the

use of an RGB lighting controller (sold separately). For

optimal performance, we recommend using the

JL Audio marine lighting controller (MLC-RW).

While these speakers are designed to be water

and spray resistant, not designed to be they are

submerged or to withstand high-pressure water

spray. Please exercise care when washing your

boat to avoid damaging your speaker . Do not s

install on submersibles, personal watercraft or any

other vessel likely to be under water at any time.

Prolonged exposure to sound pressure levels in

excess of 100dB can cause permanent hearing

loss. This high-performance speaker can

exceed this level. Please exercise restraint in its

operation in order to preserve your ability to

enjoy its fidelity.

When installing in your vessel, it is speakers

extremely important to secure firmly.them This

applies not only to the speakers themselves,

but also structure they are mounted to. If any

not firmly attached, the speaker can become s

dangerous projectile in a collision. Please s

review the mounting information carefully and

use the supplied marine-grade hardware to

mount this product.

It is absolutely vital that your coaxial speaker

system is connected as shown in this manual.

Failure to connect the system as shown will

result in damage to your speakers which

is NOT covered under warranty. Do not

substitute different crossover networks.

Do not attempt to remove the tweeter from

the bridge (Sport) or the grille (Classic). Do

not attempt to remove the lighting LEDs from

from the speaker. The tweeter and LEDs are

permanently fixed and attempting to remove

them will cause damage and this damage will

not be covered under warranty.

TWEETER PROTECTION

The crossover networks are equipped with

an advanced electronic tweeter protection circuit

designed to minimize the possibility of tweeter

failure. This electronic device monitors current

going to the tweeter and will disconnect the tweeter

from the signal when it senses overload. Should

this occur while listening to the audio system,

simply reduce the volume for a few seconds and the

protection circuit will reset itself automatically.

BEFORE YOU BEGIN INSTALLING

• Check with your local waterway authority

for any regulations regarding the use of

accent/speaker lighting on your vessel.

• Turn off the audio system. It is also advisable

to disconnect your battery system whenever

performing installation work.

• Before cutting, drilling or inserting any screw,

check clearances on both sides of the planned

mounting surface. Also check for any potential

obstacles, such as wiring harnesses, fuel lines,

hydraulic lines, etc. Check both sides of the

vessel before cutting any holes.

• If you are running cables through bulkheads,

drill holes for the cable and use a urethane

or plastic grommet to protect the wire from

chafing in the hole. Make sure that the cables

will clear any mechanical devices in the boat

and secure them with wire ties.

• Wear protective eyewear at all times and a dust

mask and gloves when drilling or cutting.

INSTALLING THE SPEAKERS

These speakers are specifically designed for

infinite-baffle applications. In other words, this

means that they are designed to operate without

an enclosure behind them.

Once mounting locations have been

established, run speaker cables from the amplifier

outputs to the mounting locations. For LED

equipped models, now is also a good time to run

wires to each speaker location for LED activation.

INSTALLATION PROCEDURE

Diagrams A & B (page 7) shows typical

installation procedures into a fiberglass panel,

using the supplied hardware. Always follow

proper safety procedures. Use eye-protection at all

times and a dust mask and gloves when cutting.

1) Choose a flat mounting surface that has

sufficient depth and air space behind it to

accept the speaker.

2) Using a hole saw or jigsaw, cut a mounting

hole for your respective speaker model

(see “Mounting Hole Diameter (D)”

specifications, page 2). If using a jigsaw,

tracing the supplied mounting template

will provide you with an accurate line on

which to cut.

3) Place the speaker in the hole (or use the

mounting template) and mark the screw hole

locations using a sharp, pointed tool.

4) Remove the speaker and drill a pilot hole (see

the Pilot Hole Recommendations chart on

page 6) in each of the screw locations.

It is also advisable to use a hand-driven

countersink tool on each hole to further

inhibit gel-coat cracking of fiberglass panels.

5) Connect the speaker wires from the

amplifier to the woofer connections (see

Speaker Connections on page 6).

6) If equipped, connect the LED circuit leads

(see page 4).

8) Place the speaker into the opening.

9) While holding the speaker firmly in its

mounting location, place a #8 screw (with

washer) at each pilot hole location and snug

in a criss-cross pattern, then tighten with a

hand screwdriver in a criss-cross pattern.

Non-standard installations may require different

hardware. Always use marine-grade, stainless-steel

fasteners to ensure a secure, reliable installation.

Specyfikacje produktu

Marka:	JL Audio
Kategoria:	głośnik
Model:	M6-880X

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio M6-880X, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik JL Audio

JL Audio M3 Instrukcja

3 Kwietnia 2025

JL Audio C6-275cm Instrukcja

7 Lutego 2025

JL Audio C6-100ct Instrukcja

4 Października 2024

JL Audio C6-650 Instrukcja

4 Października 2024

JL Audio CF-350mt Instrukcja

4 Października 2024

JL Audio C6-650cw Instrukcja

4 Października 2024

JL Audio SA-TPOD-100-BK Instrukcja

29 Września 2024

JL Audio C5-525x Instrukcja

20 Września 2024

JL Audio C5-570 Instrukcja

18 Września 2024

JL Audio M3-770X Instrukcja

16 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Turbosound PQ12-SB Instrukcja

3 Kwietnia 2025

Trust Tytan GXT 658 Instrukcja

3 Kwietnia 2025

Turbosound PQ15-YB Instrukcja

3 Kwietnia 2025

Klipsch Synergy KSB-S1 Instrukcja

3 Kwietnia 2025

Klipsch Synergy KSF-10.5 Instrukcja

3 Kwietnia 2025

Klipsch kO-R1 Instrukcja

3 Kwietnia 2025

Klipsch Synergy SB-1 Instrukcja

3 Kwietnia 2025

Klipsch Reference RB-5 II Instrukcja

3 Kwietnia 2025

Klipsch Contractor CS-800-R Instrukcja

3 Kwietnia 2025

Klipsch Synergy SC-1 Instrukcja

3 Kwietnia 2025