Instrukcja obsługi JL Audio C1-075ct

JL Audio głośnik C1-075ct

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio C1-075ct (8 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
Thank you for choosing JL Audio loudspeakers for
your automotive sound system.
We strongly recommend that you have your new loudspeakers installed by
an authorized JL Audio dealer. Your authorized dealer has the training,
expertise and installation equipment to ensure
optimum performance of these loudspeakers in your vehicle.
If you decide to install the loudspeakers yourself, please read this manual
thoroughly to familiarize yourself with their installation
requirements and setup procedures.
Should you have any questions regarding the instructions in this manual,
please contact your authorized JL Audio dealer for assistance, or call the
JL Audio Technical Support Department at (954) 443-1100
during business hours (USA - Eastern Time Zone).
0.75-inch (19 mm) Component Tweeters
OWNER’S MANUAL
2 | JL Audio - C1-075ct Owners Manual
Due to ongoing product development, all specifications are subject to change without notice.
Tweeter Fixture Physical Dimensions Flush-Mount Surface-Mount
Fixture Outer Diameter (A) 1.67 in / 42 mm 1.71 in / 43 mm
Fixture Mounting Hole Diameter (B) 1.46 in / 37 mm N/A
Fixture Mounting Depth (C) 0.40 in / 10 mm N/A
Tweeter Frontal Protrusion (D) 0.23 in / 6 mm 0.76 in / 19 mm
B
A
D
C
D
A
B
A
C
Crossover Network Physical Dimensions
Width (A) 1.96 in / 50 mm
Height (B) 0.90 in / 23 mm
Depth (C) 1.34 in / 34 mm
3
C1-075ct SPECIFICATIONS
Continuous Power Handling: 50 Watts
Recommended Amp Power: 20-50 Watts / ch. (RMS)
Efficiency: 91 dB @ 1W / 1m | 97 dB @ 1W / 0.5m
Sensitivity: 92 dB @ 2.83V / 1m
Nominal Impedance: 6 ohm
Frequency Response: 4 kHz - 24 KHz ± 3 dB
Tweeter:
Edge-driven, silk-suspended aluminum dome
0.75 in. (19 mm) diameter diaphragm / voice coil
Ferrofluid cooling / damping
Neodymium Magnet
Crossover:
2nd order, high-pass filter with inductor and
electrolytic capacitor
Included Components and Parts:
Two (2) C1-075ct 0.75-inch (19 mm) tweeters
• Two (2) surface-mount tweeter fixtures
Two (2) C1-075cthp in-line, high-pass filters on
4 ft. (1.2 m) wire harnesses
Two (2) metal spring clips (for tweeter flush-mounting)
• Four (4) #6 x .625-inch (22 mm) sheet metal screws
Two (2) 10mm stud bolts with fixed M4 nut
Two (2) 25mm stud bolts with fixed M4 nut
Two (2) M5 nuts
GETTING STARTED
Turn off the audio system. It is also
advisable to disconnect the negative
() terminal of your vehicle’s battery
whenever performing installation work.
Before cutting, drilling or inserting any screw,
check clearances on both sides of the planned
mounting surface. Also check for any potential
obstacles, such as window tracks and motors,
wiring harnesses, etc. Check both sides of the
vehicle, many vehicles are not symmetrical!
Always wear protective eyewear.


Specyfikacje produktu

Marka: JL Audio
Kategoria: głośnik
Model: C1-075ct

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio C1-075ct, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje głośnik JL Audio

JL Audio

JL Audio C6-100ct Instrukcja

4 Października 2024
JL Audio

JL Audio C6-650 Instrukcja

4 Października 2024
JL Audio

JL Audio CF-350mt Instrukcja

4 Października 2024
JL Audio

JL Audio C6-650cw Instrukcja

4 Października 2024
JL Audio

JL Audio C5-525x Instrukcja

20 Września 2024
JL Audio

JL Audio C5-570 Instrukcja

18 Września 2024
JL Audio

JL Audio M3-770X Instrukcja

16 Września 2024
JL Audio

JL Audio C1-690 Instrukcja

14 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik