Instrukcja obsługi Jensen XDA95RB

Jensen odbiornik XDA95RB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Jensen XDA95RB (10 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/10
NSA1124-V01
2025
XDA91RB,92RB,94RB,95RB
XDA SERIES
Preparation
Please read entire manual before installation. Due to the technical nature
of ampliers, it is highly recommended that your amplier is installed by a
professional installer or an authorized dealer.
Before You Start
• Disconnect negative battery terminal. (consult a qualied technician for
instructions)
• Avoid installing the amplier where it would be subject to high temperatures, such
as from direct sunlight, or where it would be subject to dust, dirt or excessive
vibration.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• All amplier installations require power, signal and speaker wires (not included).
• An amplier installation kit (sold separately) is highly recommended to facilitate
the installation. Consult your dealer for recommendations.
Mounting Location
• Choose a mounting location for the amplier. Suggested locations include under a
seat or in the trunk.
• The amplier can be mounted horizontal (recommended) or vertical. For optimum
performance, make sure to provide at least 1" of space around all sides. Do not
mount the amplier under carpets or where airow is restricted.
• Do not install the amplier where it may be exposed to moisture.
• The optimum mounting location varies between vehicles. Remember to test all
amplier functions before completing the nal mounting procedure.
TYPICAL
MOUNTING
METHOD
1
XDA SERIES
18
0
XDA SERIES
NOTE:
Be sure to follow specic instructions included with your amplier installation kit
(not included with this amplier). The information below should be used as a general
guideline only.
Power Wire (+12V)
• Disconnect negative battery terminal before proceeding. Consult a qualied
technician for instructions if you are unsure.
• Plan wire routing before cutting any wires to length. Begin by routing the power
+12V wire from the battery to the amplier location. Use a grommet when running
wires through the rewall or metal openings. Avoid running the power wire near
existing vehicle wiring to prevent induced noise from entering the audio system.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s
electrical system.
Ground Wire (GND)
• The amplier ground wire should be as short as possible (no more than 36" or
1 meter). Choose a clean unpainted section of metal or the vehicle chassis when
attaching the ground connection. Be sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
• The remote turn-on wire connects to the head unit's amplier turn-on lead or
power antenna output.
Speaker Wires
• Choose adequate gauge speaker wire depending on your exact amplier/speaker
combination. Be sure to observe polarity when connecting.
• Do not ground any speaker wires or connect any speaker wires together.
Input Signal
• The amplier's input signal connects to the head unit's low level (RCA) or high level
(speaker wire) outputs.
• Low level input signals deliver the best performance. If unavailable, use the high
level inputs - when interfacing with factory head unit for instance.
Power / Protect Indicators
• Colored LED indicators illuminate from the plastic power terminal.
• The blue LED illuminates during normal operation (POWER) and the red
LED indicator is visible when the amplier detects a fault ( PROTECT).
CAUTION
• Do not use both low and high level inputs at the same time. Connect only one or the
other.
• Keep low level inputs away from any power wires to avoid engine noise.
• Never run any wires underneath or outside the vehicle.
Connection Descriptions
2
Notes
XDA SERIES
17

Specyfikacje produktu

Marka: Jensen
Kategoria: odbiornik
Model: XDA95RB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Jensen XDA95RB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Jensen

Jensen

Jensen MPR210RGB Instrukcja

7 Stycznia 2025
Jensen

Jensen XDA95RB Instrukcja

10 Grudnia 2024
Jensen

Jensen CAR710-4 Instrukcja

9 Października 2024
Jensen

Jensen MPQ914 Instrukcja

4 Października 2024
Jensen

Jensen VX3518 Instrukcja

2 Października 2024
Jensen

Jensen CAR1013 Instrukcja

29 Września 2024
Jensen

Jensen CAR813 Instrukcja

29 Września 2024
Jensen

Jensen CMM10 Instrukcja

14 Września 2024
Jensen

Jensen MPR210 Instrukcja

12 Września 2024
Jensen

Jensen CM901MIR Instrukcja

10 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

ESX

ESX Signum SXE250.2 Instrukcja

8 Stycznia 2025
Marshall

Marshall MG15GFX Instrukcja

8 Stycznia 2025
Marshall

Marshall 2555X Instrukcja

8 Stycznia 2025
Marshall

Marshall MG50GFX Instrukcja

8 Stycznia 2025
Marshall

Marshall JVM410C Instrukcja

8 Stycznia 2025
QSC

QSC CX4 Instrukcja

7 Stycznia 2025
QSC

QSC DPA4.2Q Instrukcja

7 Stycznia 2025
QSC

QSC USA 400 Instrukcja

7 Stycznia 2025
QSC

QSC DPA4.3Q Instrukcja

7 Stycznia 2025
QSC

QSC USA 900 Instrukcja

7 Stycznia 2025