Instrukcja obsługi Jensen VM9214BT

Jensen odtwarzacz DVD VM9214BT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Jensen VM9214BT (12 stron) w kategorii odtwarzacz DVD. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
1
VM9214BT
VM9214BT Head Unit
Single DIN Sleeve
Wiring Harness
Parking Brake Sensor Extension Wire
Mounting Hardware
Cosmetic Trim Ring
3.5mm to 3.5mm Media Adaptor Cable
Owners Manual
Installation Guide
What’s in the Box
You will need these tools and supplies to install your VM9214BT:
• Torx type, fl at-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
Tools and Supplies
Installation Guide
Instruccionnes de Instalación
Instructions d’installation
WARNING! Never install this unit where operation and viewing could interfere with safe driving
conditions.
Para obtener instrucciones en Español, diríjase a la página 5. Pour des instructions en Francais, référez-vous à la page 9.
EJECT
A / V
INPUT
VM9214BT
DISP
M
U
T
E
2
TAB
DASHBOARD
DASHBOARD
TAB
Optional Equipment
• NAV102: Allows you to access navigation features. All installation and operating instructions are included
with the navigation module.
• Rear Camera
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to in-
stallation.
NOTE: If the VM9214BT is to be installed in a car equipped with an on-board drive or navigation computer, do
not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Pre-installation
Remove the four screws that attach the mounting sleeve to the
radio and remove the sleeve.
Install the mounting sleeve.
a. Install mounting sleeve into the dashboard or optional
adapter. Do not force the sleeve into the opening or cause
it to bend or bow.
b. Locate the series of bend-tabs along the top, bottom and
sides of the mounting sleeve. With the sleeve fully insert-
ed into the dashboard opening, bend as many of the tabs
outward as necessary so that the sleeve is fi rmly secured
to the dashboard.
c. Install support strap to make the unit more stable.
Place the radio in front of the dashboard opening so the wiring
can be brought through the mounting sleeve.
CAUTION! Be careful not to damage the car wiring.
1
2
3
3
Wiring
WARNING! Only connect the unit to a 12-volt power supply with proper grounding.
Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, reconnect the bat-
tery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The
VM9214BT uses one 15 amp fuse, located in the black fi lter box in-line with the main wire harness.
Final Installation
After completing the wiring connections, turn the unit on to confi rm operation (ignition switch must be on). If
unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off
the ignition switch and proceed with fi nal mounting of the chassis.
Connect wiring adapter to existing wiring harness.
Connect antenna lead.
Carefully slide the radio into the mounting sleeve, making
sure it is right-side-up, and secure with the original 4 screws.
Attach one end of the perforated support strap (supplied) to
the screw stud, which is screwed into the threaded insert on
the back of the unit, using the hex nut provided. Fasten the
other end of the perforated strap to a secure part of the
dashboard either above or below the radio using the screw
and hex nut provided. Bend the strap to position it as
necessary.
Replace any items you removed from the dashboard.
ISO-DIN Installation
Remove mounting sleeve brackets.
Remove trim ring.
Mount factory brackets on new radio using existing screws
from old radio.
Slide radio chassis into dash opening and secure.
Re-install dash panel.
EJE
CT
A/V
INPUT
EJE C
T
A/
VIN
PU T
1
2
3
4
5
1
2
3
4
5
CAUTION! The rear of the radio must be
supported with the strap to prevent dam-
age to the dashboard from the weight of
the radio or improper operation due to
vibration.
NOTE: For proper operation of the CD/
DVD player, the chassis must be mounted
within 20° of horizontal. Make sure the unit
is mounted within this limitation.
Remove Mounting
Sleeve Brackets
EJE C
T
A/ V
INPU T

Specyfikacje produktu

Marka: Jensen
Kategoria: odtwarzacz DVD
Model: VM9214BT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Jensen VM9214BT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odtwarzacz DVD Jensen

Jensen

Jensen CDR5620 Instrukcja

19 Września 2024
Jensen

Jensen VM9214BT Instrukcja

22 Sierpnia 2024
Jensen

Jensen VM9424 Instrukcja

20 Sierpnia 2024
Jensen

Jensen VM9214 Instrukcja

8 Sierpnia 2024
Jensen

Jensen CAR8000 Instrukcja

6 Sierpnia 2024
Jensen

Jensen CDR6221 Instrukcja

6 Sierpnia 2024
Jensen

Jensen CDR7011 Instrukcja

3 Maja 2024

Instrukcje odtwarzacz DVD

Najnowsze instrukcje dla odtwarzacz DVD

AKAI

AKAI ad70h Instrukcja

14 Stycznia 2025
Qmedia

Qmedia QDVD-060 Instrukcja

14 Stycznia 2025
Medion

Medion LIFE P72022 (MD 84873) Instrukcja

13 Stycznia 2025
Samsung

Samsung DVD-P146 Instrukcja

10 Stycznia 2025
Samsung

Samsung DVD-E319 Instrukcja

10 Stycznia 2025
Samsung

Samsung DVD-S426KG Instrukcja

10 Stycznia 2025
LG

LG DR176H Instrukcja

10 Stycznia 2025
LG

LG DAT-200 Instrukcja

10 Stycznia 2025
LG

LG D76 Instrukcja

10 Stycznia 2025
LG

LG DVX141 Instrukcja

9 Stycznia 2025