Instrukcja obsługi JennAir MKC4150ES

JennAir Magnetostrykcja MKC4150ES

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JennAir MKC4150ES (20 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
INSTALLATION INSTRUCTIONS
BUILT-IN MICROWAVE OVEN KIT
INSTRUCTIONS D’INSTALLATION
ENSEMBLE FOUR À MICRO-ONDES
ENCASTRÉ
This product is suitable for use above electric built-in ovens or warming drawers. This product is not suitable for use below cooktops.
This Built-In Kit is designed for use with Jenn-Air Microwave Oven model specifying JMC3415ES Built-In Kit on the serial tag on the
front of the microwave oven.
These Installation Instructions cover different models. The appearance of your particular model may differ slightly from the illustrations
in these Installation Instructions.
Please read these instructions thoroughly before beginning installation.
Ce produit est conçu pour être installé au-dessus d’un four électrique encastré ou d’un tiroir-réchaud. Ce produit n’est pas conçu
pour être installé sous une table de cuisson. L’ensemble four à micro-ondes encastré est conçu pour être utilisé avec les modèles
de fours à micro-ondes Jenn-Air dont la plaque avant avec numéro de série indique le numéro d’ensemble encastré JMC3415ES.
Ces instructions d’installation couvrent plusieurs modèles. L’apparence de votre modèle peut différer légèrement des illustrations
présentes dans ce manuel.
Lire ces instructions attentivement avant de commencer l’installation.
IMPORTANT:
Save for local electrical inspector’s use.
IMPORTANT :
À conserver pour consultation par l’inspecteur
local des installations électriques.
NOTE: Do not remove protective film from trim kit frame before
installing ducts and other mounting hardware. Only remove film
just before installing trim on cabinet.
REMARQUE : Ne pas retirer le film de protection du cadre de
la trousse de garniture avant l’installation des conduits et de la
quincaillerie de fixation. Enlever le film juste avant l’installation
du cadre sur le placard.
W10781779A
Table of Contents/Table des matières
BUILT-IN MICROWAVE OVEN SAFETY ........................................2
INSTALLATION REQUIREMENTS .................................................2
Tools and Parts .............................................................................2
Location Requirements ................................................................3
Minimum Dimensions...................................................................3
Product Dimensions .....................................................................5
Electrical Requirements ...............................................................5
INSTALLATION INSTRUCTIONS ...................................................6
Install Rear and Top Ducts ...........................................................6
Install Rails and Bottom Duct ......................................................7
Install Microwave Oven and Trim Kit Frame ................................8
Complete Installation ...................................................................9
To Remove Trim Kit Frame ...........................................................9
ASSISTANCE ..................................................................................9
SÉCURITÉ DU FOUR À MICRO-ONDES ENCASTRÉ ..............10
EXIGENCES D’INSTALLATION ...................................................10
Outils et pièces ...........................................................................10
Exigences d’emplacement .........................................................11
Dimensions minimales ...............................................................11
Dimensions du produit ...............................................................13
Spécifications électriques ..........................................................13
INSTRUCTIONS D’INSTALLATION .............................................14
Installer les conduits arrière et supérieur ...................................14
Installer les rails et le conduit inférieur .......................................15
Installer le four à micro-ondes et le cadre
de la trousse de garniture ..........................................................16
Terminer l’installation ..................................................................17
Enlever le cadre de la trousse de garniture ...............................17
ASSISTANCE 17 ................................................................................
2
BUILT-IN MICROWAVE OVEN SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Tools Needed
■Phillips #2 screwdriver
■Measuring tape
■Combination square/straight edge
■Pencil
■Drill (for wall cabinet installations)
■■Z\zn" (0.16 cm) drill bit (for wall cabinet installations)
■6" (15.2 cm) level
Parts Supplied
Check that all parts are included.
#8-14 x " screws (20)Z\x
Duct 1 (1) Duct 2 (1)
Duct 3 (1) Duct 4 (1)
Duct 5 (1)
Mounting Rails (2)
Trim Kit Frame (1)
Shims (1 pack)
#10- " x " self-drilling screw (2)C\v B\zn
Bottom Duct Attachment
Bracket (2)
Bottom Duct (1)
NOTE: #8-14 x " screws will come in 2 separate packages.Z\x
3
The microwave oven may be located in a cabinet and/or above
a built-in oven or warming drawer. Check the opening where
the microwave oven will be installed. The bottom surface of the
cutout must be a minimum of 36" (91.4 cm) above the floor.
The location must provide:
■Wood cabinetry.
■Cutout opening that is plumb and square. See “Minimum
Installation Clearances” in the “Minimum Dimensions” section.
■Cutout floor that is solid, level, and flush with bottom of
cabinet cutout.
■Support for weight of at least 150 lbs (68 kg) which includes
microwave oven and items placed inside.
■Grounded electrical outlet. See the “Electrical Requirements”
section.
■Minimum installation clearances for installation location.
See the “Minimum Dimensions” section.
■Complete enclosure around the recessed portion
of the microwave oven, including a solid, full ceiling.
■A level floor – front to back and left to right.
Minimum Dimensions
Minimum Installation Clearances
For proper installation, the following minimum clearances must exist above and below the cutout opening.
Above Cabinet/Storage Drawer Installation Above Oven/Warming Drawer Installation
)
1"
(25 mm)
11⁄ " 2
(38 mm)
1"
(25 mm)
3"
(76 mm)
C
B
A
A. Upper cabinet
B. Lower cabinet or storage drawer
C. Lower oven or warming drawer
NOTE: The bottom surface of the cutout must be a minimum of 36" (91.4 cm) above the floor.
Location Requirements

Specyfikacje produktu

Marka: JennAir
Kategoria: Magnetostrykcja
Model: MKC4150ES

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JennAir MKC4150ES, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Magnetostrykcja JennAir

JennAir

JennAir JMW2430IM Instrukcja

17 Września 2024
JennAir

JennAir JMW2430IL Instrukcja

17 Września 2024
JennAir

JennAir JMC2427LM Instrukcja

16 Września 2024
JennAir

JennAir JMDFS24HM Instrukcja

16 Września 2024
JennAir

JennAir JMC1116AS Instrukcja

16 Września 2024
JennAir

JennAir JMC2427IM Instrukcja

16 Września 2024
JennAir

JennAir JGCP648HM Instrukcja

16 Września 2024
JennAir

JennAir JMC2430DP Instrukcja

16 Września 2024
JennAir

JennAir JMDFS24GS Instrukcja

16 Września 2024
JennAir

JennAir JMC2427DS Instrukcja

15 Września 2024

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

Sharp

Sharp R-334W Instrukcja

15 Października 2024
Whirlpool

Whirlpool WMCS7022RS Instrukcja

15 Października 2024
Insignia

Insignia NS-MW11BK5 Instrukcja

15 Października 2024
Insignia

Insignia NS-MW7RM5 Instrukcja

15 Października 2024
Maytag

Maytag UMCS5022RZ Instrukcja

15 Października 2024
Whirlpool

Whirlpool AMW 730/WH Instrukcja

14 Października 2024
Whirlpool

Whirlpool AVM 220/WP/AV Instrukcja

14 Października 2024
Daewoo

Daewoo KOR-6CDS8 Instrukcja

14 Października 2024
Pelgrim

Pelgrim MAG740 Instrukcja

13 Października 2024
Sharp

Sharp R-2V11B Instrukcja

13 Października 2024