Instrukcja obsługi JBL WR2.4

JBL Słuchawki WR2.4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JBL WR2.4 (2 stron) w kategorii Słuchawki. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
IntroductIon
These 2.4 GHz digital wireless
headphones use the latest digital
wireless technology, so you can enjoy
crystal-clear stereo music and TV
sound anywhere inside your home.
Simply connect the transmitter to your
portable device, TV set or other audio
source. Without complicated wiring
and installation, the system enables
you to enjoy thrilling, lifelike sound in
minutes. Please take a few minutes
to carefully read the instructions
below before operating your
headphones.
coMPonEnt
PArt LISt (FIG. A)
HEADPHONE RECEIVER
1. Signal link LED
2. Volume Up (+) and Down (-) Control
3. Power LED
4. Power button
5. Charging contacts
TRANSMITTER
6. Power/Signal LED
7. Charge LED
8. Charging pins
9. Attenuation (ATT) select switch
(0dB and -8dB)
10. RCA Audio In sockets
11. DC IN socket
ACCESSORIES
12. Audio cable
13. NMH AAA size batteries for
Headphone (2 pieces)
14. AC/DC adaptor
connEctIonS (FIG. B)
TRANSMITTER
1. Connect the supplied AC/DC power
adaptor to an AC wall outlet.
2. Connect the AC/DC power adaptor
cable to the DC jack located on
the rear of the transmitter. The red
Power/Audio Signal LED starts to
ash for approximately 6 seconds.
3. Connect the supplied audio cable
to the transmitter’s RCA Audio In
sockets. Connect the other end of
the cable to the audio output jack
of your portable device, TV or other
audio source. If your audio source
does not have a 3.5mm output
connector you may need to acquire
another cable (not included).
4. For TV/VCR/DVD/Hi-Fi sources, set
the ATT switch to -8dB. For portable
device sources, set the ATT switch
to 0dB
Turn on and begin playing your audio
source; the transmitter will automatically
switch on and the red Power/Signal
LED will light red when it receives an
audio signal.
HEADPHONE RECIEVER
1. To install or replace the rechargeable
batteries, carefully rotate the Right-
Hand Side (R)
Ear Pad counter-clockwise and
remove it. (Fig. C)
2. Insert the two supplied AAA
size rechargeable batteries into
the battery compartment of the
headphone housing, observing the
correct polarity.
3. After inserting the batteries, restore
the Ear Pad to the headphone
housing, according to the indication
of the arrow marking.
oPErAtIon
TRANSMITTER
Turn on the audio source to which the
transmitter is connected. The Power
/ Signal LED (6) on the transmitter
will light red when it receives an audio
signal.
HEADPHONE RECEIVER
1. Turn on the headphones by
pressing the for Power button (4)
approximately 1 second. The red
Power LED (3) will light up, and the
green LED (1) will be ashing. When
the signal link between transmitter
and receiver is established, the
green LED (1) will light up steadily.
2. Place the headphones on your head.
To obtain the desired sound level,
adjust the on the volume control (2)
headphones.
3. If interference or poor signal
reception occurs when out of range
of the transmitter, the headphones
will mute and the green LED (1)
will turn off. Move closer to the
transmitter.
4. When the headphone batteries are
at low level, the Power Red LED
(3) blinks. There will be a beeping
sound in each minute for the last 5
minutes. After that, the headphones
will switch Off automatically.
5. To charge the headphone batteries,
turn the headphones OFF by pressing
the Power button (4) for about 1
second. Place the headphones on
the transmitter’s charging cradle.
The charging process begins
automatically, and the Charge green
LED (7) will blink when the charging
contacts of the transmitter (8)
and headphones (5) make proper
contact. When the charging process
is completed, the Charge green
LED (7) will light up steadily.
NOTE: For the initial use, please
charge the batteries for 7 hours.
To ensure a long service life, fully
charge the batteries before using the
headphone for the rst time. If the
headphones are not in use, please
store them on the transmitter’s
charging cradle. (Fig. D)
IMPORTANT
1. Switching Off
a) To protect the transmitter and
conserve power, the transmitter
will switch off automatically if
there is no audio source signal
for approximately 3 minutes. If
the audio source signal returns,
the transmitter will automatically
switch on. To listen, press the
headphones’ Power button again
for approximately 1 second.
b) The headphones will automatically
switch off if they receive no signal
from the transmitter for 3 minutes.
2. Make sure the headphones are
turned off when charging is in
process.
3. Use only the rechargeable AAA
batteries supplied with the
headphones. When the headphones
are not in use, turn the headphones
OFF.
4. Ensure the charging socket located
on the right headphone housing
connects securely with the charging
prongs on the transmitter cradle.
According to the capacity of the
included rechargeable batteries, the
battery charging process will take
approximately 5 to 7 hours.
This device must be used with the AC/
DC adaptor supplied in the package.
WArnInG
• Never attempt to recharge
conventional dry cell batteries.
• Batteries (battery pack or batteries
installed) shall not be exposed to
excessive heat such as sunshine, re
or the like.
• Never use another type of battery or
non-rechargeable batteries to replace
the supplied rechargeable (LR03/
AAA) batteries
• Excessive sound pressure from
earphones and headphones can
cause hearing loss.
• Before charging the headphones
batteries, always make sure that the
batteries in the headphones are the
rechargeable types.
• Dispose of spent dry or rechargeable
batteries conforming to local waste
disposable rules. Never throw
batteries into re.
• Operate the transmitter with the
supplied 5V DC, 550mA AC/DC
adapter only. Check that the AC
voltage stated on the AC/DC adapter
is the same as that available in your
country. Using the transmitter with a
different AC/DC adapter makes the
warranty void.
• Always switch the headphones OFF
after use.
• Never try to open the headphone or
transmitter case. Refer servicing to
qualied service personnel only.
• Never use alcohol, petroleum-based
cleansers, or paint thinners to clean
the headphones or transmitter.
• Use the equipment for the
applications described in this manual
only. JBL cannot accept any liability
for damages resulting from improper
handling or misuse.
• Do not subject this equipment to
any environments where drops or
splashes can make contact with
the equipment and make sure that
no objects lled with water, such as
vases, are placed on the equipment.
• This equipment is fully disconnected
from the mains power by pulling the
mains plug out of the wall outlet. The
power disconnect procedure must
be easily accessible.
• The mains plug on the mains cable
must always be ready to use.
JBL® Wr2.4
Wireless Rechargable Headphones
quIck-StArt GuIdE
trouBLESHootInG
NO SOUND
• Ensure the AC/DC adaptor is fully
inserted into the AC outlet and the
power connection input on the
transmitter.
• Ensure you’ve inserted the batteries
correctly.
• Ensure the headphones are switched
ON.
• Headphone battery charge level
may be too low, fully recharge the
batteries.
• Ensure that the connected audio
source device is switched ON and
is playing.
• The volume of the headphones may
be too low. Increase the volume of
the audio source.
DISTORTION
• Ensure the volume level of the
headphones is set to an appropriate
level.
• If the headphones are too far from the
transmitter, move them closer.
• If the audio signal input level is too
low. Increase the volume of the audio
source.
INTERFERENCE
• If you encounter inference from WLAN
systems, devices or other Bluetooth
2.4GHz systems we recommend
moving the transmitter away from the
other device / system.
• Your JBL WR2.4 scans for a free
frequency slot each time you plug
in the power cable into the DC jack
of the transmitter. If an additional
2.4GHz source appears after you
initially set up your WR2.4, we
recommend that you unplug the
power cable for 1 minute and
then re-connect it to allow a new
frequency scan.
tEcHnIcAL
SPEcIFIcAtIonS
Transmission Mode: UHF Stereo
Carrier Frequency: 2.4GHz Digital
Operation Voltage:
Transmitter: DC 5V 550mA
Headphone: 2 x AAA size
rechargeable NiMH batteries
(included)
Frequency Response: 18Hz- 20kHz
S/N Ratio: 75dB
Operating Distance: typically 20
meter/ 65 ft
HARMAN International Industries, Incorporated
8500 Balboa Boulevard, Northridge, CA 91329 USA
© 2013 HARMAN International Industries, Incorporated. All rights reserved. JBL is a
trademark of HARMAN International Industries, Incorp orated, registered in the United
States and/or other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc., and any use of such marks by HARMAN International Industries, Incorporated, is
under license. Other trademarks and trade names are those of their respective owners.
All Rights Reserved. Features, specifications and appearance are subject to change
without notice.
Part No. JBLP5356 Rev: A www.jbl.com
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference with one or more of
the following measures:
• Readjust or distance the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Shielded cables and I/0 cords must be used or this equipment. Changes
or modications not explicitly proved in writing by JBL may make the user’s
authority to operate this equipment void. This device complies with Part
15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference. and (2) this device must
accept any interference.
JBL hereby declares that the WR2.4 headphones comply with the essential requirements
and other relevant provisions of Directive 1999/5/EC. To order your free copy of our
Declaration of Conformity, please visit http://www.jbl.com. or contact sales@www.jbl.com.

Specyfikacje produktu

Marka: JBL
Kategoria: Słuchawki
Model: WR2.4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JBL WR2.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Słuchawki JBL

JBL

JBL Tune 215TWS Instrukcja

9 Października 2024
JBL

JBL Quantum 100M2 Instrukcja

8 Października 2024
JBL

JBL Soundgear Sense Instrukcja

4 Października 2024
JBL

JBL Vibe Buds Instrukcja

3 Października 2024
JBL

JBL Live 770NC Instrukcja

1 Października 2024
JBL

JBL Tour One Instrukcja

30 Września 2024
JBL

JBL Tune 670NC Instrukcja

28 Września 2024
JBL

JBL Quantum TWS Air Instrukcja

27 Września 2024
JBL

JBL Tune 230NC TWS Hoofdtelefoon Instrukcja

26 Września 2024
JBL

JBL Live 660NC Hoofdtelefoon Instrukcja

23 Września 2024

Instrukcje Słuchawki

Najnowsze instrukcje dla Słuchawki

Klipsch

Klipsch R6i Instrukcja

15 Października 2024
Vakoss

Vakoss MH954 Instrukcja

14 Października 2024
Skullcandy

Skullcandy Cassette Instrukcja

14 Października 2024
Jabra

Jabra Wave Corded Instrukcja

14 Października 2024
Manta

Manta MM65 Instrukcja

14 Października 2024
AKG

AKG Y600NC Instrukcja

14 Października 2024
Audio-Technica

Audio-Technica ATH-ANC29 Instrukcja

13 Października 2024
Daewoo

Daewoo AVS1421 Instrukcja

13 Października 2024
Vakoss

Vakoss MH942 Instrukcja

13 Października 2024
SuperTooth

SuperTooth Freedom Instrukcja

13 Października 2024