Instrukcja obsługi JBL Decade DS100

JBL subwoofer Decade DS100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JBL Decade DS100 (4 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
D E C A D E
™
D S 1 0 0 , D S 1 2 0
G E N U I N E J B L
2
A Few Words About Enclosures
Your Decade Series subwoofer requires
an enclosure to realize its full low-
frequency response. The speaker’s design
is flexible enough to produce exceptional
results no matter whether you specify a
small sealed, vented or bandpass enclo-
sure. In vented and bandpass enclosures,
box size and port tuning frequency will
also help dictate the low-frequency
performance and output capability of
your system.
Your Decade Series subwoofer will also
work in infinite baffle applications where
there is no space or budget to build a
box. Be aware that infinite baffle or “free
air” mounting will reduce the power han-
dling of any subwoofer compared to an
application using an enclosure.
Finally, any deviation from recommended
enclosure volumes or port dimensions
should be made using dedicated
enclosure-design software, such as JBL
Speakershop™. If this type of software is
not available to you, look for assistance
on JBL’s Web site at www.jbl.com or from
your authorized JBL dealer.
Your Car and Bass Reproduction
Depending on the size of the vehicle’s
interior listening space, reproduced
frequencies below 80Hz are actually
boosted by nearly 12dB per octave as
frequency decreases. NOTE: This effect,
known as the vehicle’s transfer function,
plays an important part in shaping the
overall in-car response and is displayed
graphically along with freespace
response on the enclosed data sheet for
your Decade Series subwoofer.
Enclosure Calculations and
Building Boxes
Use the recommended box designs on
the enclosed data sheet. Choose cabinet
dimensions to fit your vehicle, but do not
change the enclosure’s volume. Doing so
will change the tuning frequency of the
enclosure and may adversely affect final
performance. If you cannot perform the
necessary calculations yourself, please
contact your authorized JBL dealer for
help and for information about JBL
Speakershop, a dedicated enclosure-
design software program for experienced
car-audio enthusiasts.
In addition, there are a number of points
you’ll want to keep in mind as you con-
struct an enclosure:
1. Use 3/4" (19mm) MDF (medium-density
fiberboard) or marine birch plywood to
build an enclosure. Enclosures for 12"
and larger subwoofers, or small sub-
woofers driven by high power ampli-
fiers, should be constructed using 1"
(25mm) material.
2. Seal all joints with glue and screws; do
not use nails. We recommend “deck” or
“zip” screws since they have coarse
threads for better grip and don’t require
pre-drilling holes. Once the box has
been tested, seal all interior joints with
silicone caulk.
3. Depending on the application, fill the
enclosure according to the design you
have chosen from the enclosed data
sheet in one of three ways: zero-percent
fill (i.e., no fill), 50-percent fill (i.e.,
1"-thick polyfill sheets on all inside
walls except where subwoofer is
mounted), or 100-percent fill (i.e., entire
box is stuffed with loosely packed poly-
ester fiberfill).
Thank you for choosing a JBL Decade™
Series subwoofer. Decade Series sub-
woofers are designed to suit a broad
range of mobile-audio applications and
can be used in a wide variety of enclo-
sure types to produce extended, powerful
bass in a limited amount of vehicle
space. To ensure maximum subwoofer
performance, we strongly recommend
that installation be left to a qualified pro-
fessional. Although these instructions
explain how to install a JBL Decade
Series subwoofer in a general sense, they
do not show box construction details and
exact installation methods for your partic-
ular vehicle. If you do not feel you have
experience, do not attempt the installa-
tion yourself, but instead ask your autho-
rized JBL dealer about professional
installation options.
Remember to keep your sales receipt
with this manual in a safe place so both
are available for future reference.
3
4. Use PVC or ABS pipe for ports. Keep in
mind that the openings at either end of
the port must be at least one port
diameter away from any obstructions,
including filling material inside the box.
Rectangular vents can be used as long
as the cross-section surface area
matches the recommended port-area
values in the enclosed data sheet.
Power-Handling Limitations
The power-handling capability of any
woofer is related to both its ability to dis-
sipate heat and maximum excursion lim-
its of its cone. Once the speaker’s voice
coil moves outside the magnetic gap,
power can no longer be converted into
motion and all the amplifier’s power is
converted into heat in the voice coil. This
voice-coil heating is the largest detriment
to speaker longevity, so overexcursion
should be avoided. Since speaker-cone
excursion is different for each type of
enclosure, power handling is different for
each enclosure.
• Voice-coil overheating and burning, due
to overexcursion, are often caused by
overdriving an amplifier into “clipping.”
A severely clipped signal, or square
wave, contains nearly twice the power
of a clean sine wave at the same level.
Bass that sounds broken up and distort-
ed at higher volumes usually indicates
that the amplifier is clipping and is
being asked to deliver power beyond
its rated power.
• Infinite baffle or “free air” mounting
applications allow for greater cone
excursion than subwoofers mounted in
an enclosure. In order to compensate,
recognize that the power-rating value of
the subwoofer will likely be half its
rated power in this application.
Sealed enclosures exert the most control
over the motion of a subwoofer because
the air acts like a spring against the
motion of the woofer cone. Larger boxes
allow for more excursion, thus providing
more low-frequency output for the
amount of power used. When placed in a
sealed box larger than its compliance
(Vas), the subwoofer will perform as if it
were in an infinite baffle installation.
Vented and bandpass enclosures have
the lowest amount of excursion for the
amount of sound output. This is a result
of port tuning reinforcing the sound out-
put of the speaker. Vented boxes do not
provide adequate woofer control when
driven below the port tuning range, so
proper design is important. A vented
bandpass box will have the lowest overall
cone excursion at the expense of limited
bandwidth.
• Study the excursion curves on the
enclosed JBL Decade Series data sheet
and note the differences for different
enclosure applications. The type and
size of box used will produce different
excursion demands on the enclosed
subwoofer and, consequently, different
levels of power handling. As long as
recommended parameters are used,
the subwoofer will perform properly in
its enclosed environment. However,
any design deviation may result in less
than optimum performance, and may
also subject the subwoofer to overex-
cursion (i.e., where the voice coil leaves
the gap) that can eventually damage
the speaker. For additional help with
this issue, please contact your autho-
rized JBL dealer.

Specyfikacje produktu

Marka: JBL
Kategoria: subwoofer
Model: Decade DS100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JBL Decade DS100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer JBL

JBL

JBL SSW-4 Instrukcja

26 Grudnia 2024
JBL

JBL SSW-2 Instrukcja

26 Grudnia 2024
JBL

JBL 800.4GTi Instrukcja

25 Grudnia 2024
JBL

JBL ARC SUB10 Instrukcja

25 Grudnia 2024
JBL

JBL Cinema Sound CSS10 Instrukcja

25 Grudnia 2024
JBL

JBL Grand Touring GTO1212BP Instrukcja

25 Grudnia 2024
JBL

JBL Grand Touring GTO1214BR Instrukcja

25 Grudnia 2024
JBL

JBL Cinema Vision CVSUB50 Instrukcja

25 Grudnia 2024
JBL

JBL Decade DS100 Instrukcja

25 Grudnia 2024
JBL

JBL Decade DS125 Instrukcja

25 Grudnia 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

Axton

Axton ATB120 Instrukcja

28 Grudnia 2024
Origin Acoustics

Origin Acoustics OSUB8 Instrukcja

28 Grudnia 2024
Origin Acoustics

Origin Acoustics OSUB12 Instrukcja

28 Grudnia 2024
Origin Acoustics

Origin Acoustics SUBDD12 Instrukcja

28 Grudnia 2024
Bazooka

Bazooka MBT1014 Instrukcja

27 Grudnia 2024
Bazooka

Bazooka MBT8014 Instrukcja

27 Grudnia 2024
PSB

PSB CustomSound CWS8 Instrukcja

27 Grudnia 2024
Soundstream

Soundstream Tarantula T5.152 Instrukcja

26 Grudnia 2024
Monitor Audio

Monitor Audio CLG-W12 Instrukcja

26 Grudnia 2024
Infinity

Infinity Alpha 1200S Instrukcja

26 Grudnia 2024