Instrukcja obsługi JANDY XL 3

JANDY Heater XL 3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JANDY XL 3 (1 stron) w kategorii Heater. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
D C
T
T
F
F
Thermostat
E971
115 VAC
Neutral
ON-OFF Switch
E782
E786
Twist Lock Plug
E784
Hi Limit
E771
E
F
Pressure
Switch
104089-02
G
White
Black
Black
Black
Orange
Yellow Yellow
Primary Control
N060
Transformer
N023
White Oil Pump
B A
Hi Limit
E722
Black
White
Black
Motor
N010
Ground
Current Flow
Wire Nut
Neutral
Cadmium Cell
N061
JANDY DP OIL FIRED POOL HEATER TROUBLESHOOTING
Check voltage at A
No
Yes
Check voltage at B
Check circuit breaker
No
Bad ON/OFF Switch (E782)
Yes
Check voltage at C
Loose Twist Lock Plug
Short in Wire Harness (R575)
Bad Twist Lock Plug
No
Yes
Check voltage at D
No
Bad Hi Limit (E771)
No
Yes
Check voltage at E
Loose Twist Lock Plug
Short in Wire Harness (R575)
Bad Twist Lock Plug
Check voltage at F
Yes
No
Water flow problem
Bad Pressure Switch
Misadjusted Pressure Switch
Blocked Siphon Loop Connection
Check voltage at G
Yes
No
Bad wire in Armored Cable (BX)
Heater Doesn’t Fire
Yes
Press RESET button on Primary Control Once
1) If unit fire and stays on, unit lost
prime to Oil Pump
2) If unit fires and goes out, or doesn’t
stay lit, or goes into RESET after 45
seconds …. this is a Oil Burner or
combustion problem
CALL QUALIFIED OIL SERVICE
If you press RESET on Primary Control, and
RESET button on Oil Burner Motor, and
nothing happens
1) Turn off power to heater, then
temporarily place a jumper from
T to T on the Primary Control and
turn power on. If unit fires, either the
Thermostat (E971) or the High
Limit (E722), or the Fireman’s Switch
has a problem.
2) If unit doesn’t fire, remove one of
the yellow wires from either terminal
marked F on the Primary Control.
If unit fires now, either:
Bad Cadmium Cell (N061)
Bad Primary Control, or
there is a fire in the
combustion chamber…. CALL
OIL SERVICE
Caution; Possible Electrocution: This circuit is high voltage, take extremely care when checking.
L0843, Rev A 09/05

Specyfikacje produktu

Marka: JANDY
Kategoria: Heater
Model: XL 3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JANDY XL 3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Heater JANDY

JANDY

JANDY CXI650PN Instrukcja

17 Września 2024
JANDY

JANDY LX LT Low Nox Instrukcja

17 Września 2024
JANDY

JANDY XL 3 Instrukcja

17 Września 2024

Instrukcje Heater

Najnowsze instrukcje dla Heater

Heller

Heller HOFC2000 Instrukcja

20 Września 2024
Nobo

Nobo NTL4T07-FS40 Instrukcja

20 Września 2024
Hubbell

Hubbell J1613S Instrukcja

19 Września 2024
Hubbell

Hubbell J615R Instrukcja

19 Września 2024
Prem-i-air

Prem-i-air EH1372 Instrukcja

19 Września 2024
XPower

XPower P-400 Instrukcja

19 Września 2024
Heller

Heller CTH5162 Instrukcja

19 Września 2024
Ravanson

Ravanson CH-2000M Instrukcja

19 Września 2024