Instrukcja obsługi JANDY Stain Remover

JANDY Niesklasyfikowane Stain Remover

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JANDY Stain Remover (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
1. Attach Stain Remover
applicator head to pool pole.
2. Place rubber band around
lower of bottle (see picture).
Screw vent cap on gallon
container of diluted muriatic
acid (5:1 recommended). Use
chlorine for organic stains.
4. Submerge vinyl hose tubing
and applicator in pool, stretching
tube out all the way to remove
coils.
3. Place acid container on edge
of pool at deep end. Carry
applicator and pole to opposite
side of pool.
INSTRUCTIONS FOR USING JANDY STAIN REMOVER
Muriatic acid, or similar strong chemicals, can cause
bleaching or damage to pool surfaces. Do not hold Stain
Remover over stains for longer than 10 seconds at a time.
Keep Stain Remover moving. Do not allow more than
one (1) pint of chemical to enter pool in any one Stain
Remover session (usually not more than 1-3 minutes of
use). If multiple sessions are required, wait 3 days and
repeat. NOTE: Check pool chemistry before using Stain
Remover and after, then adjust chemistry accordingly.
STAIN REMOVER USER
CAUTION
Special Applications:
For rust and other stains use muriatic acid. For algae use liquid algaecides or
chlorine. Contact your pool dealer for additional information.
CAUTION: Muriatic acid is not recommended for vinyl lined swimming
pools. Substitute with liquid algaecides or chlorine.
KEEP OUT OF REACH OF CHILDREN. READ LABEL ON ACID
CONTAINER AND WARNING ON STAIN REMOVER. CAN CAUSE
SERIOUS INJURY OR DEATH.
WARNING:
7. When all bubbling stops,
slowly lower inverted applicator
to just below water surface.
Move to stain, then lower
applicator onto stain in upright
position. Hold until acid seepage
is seen (but not more than 10
seconds). Remove and stain will
be gone. Keeping applicator in
water, proceed to other stains.
8. When stains have been
removed, walk to the bottle,
remove applicator from pool, and
slowly coil tubing in hand which
will drain acid into bottle.
Note: On severly stained pools
some lightening of the plaster
will occur.
9. Remove vent cap from acid container and submerge all equipment
(applicator, tubing, cap) for thorough rinsing by holding the applicator
against the pool return inlet for 30 seconds. After using the Stain
Remover, check you pH and adjust the pool chemistry to the
proper pH reading if necessary.
6000 Condor Drive, Moorpark, CA, USA 93021 • 707.776.8200 FAX 707.763.7785
Litho in U.S.A. © 2005 Jandy Pool Products, Inc. 0511
For technical support call 707.776.8200, ext. 260
Part #1644, Rev. C
Website: www.Jandy.com
6. Lift pole and applicator out of
water to eye level (or higher),
with applicator still inverted, until
remaining air bubbles in acid
container again stop.
5. Lower applicator to just below
water surface in inverted postion.
Hold until air bubbles rising from
applicator stop and air bubbles
in acid container stop (about 30
seconds to 1 minute).


Specyfikacje produktu

Marka: JANDY
Kategoria: Niesklasyfikowane
Model: Stain Remover

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JANDY Stain Remover, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane JANDY

JANDY

JANDY Erosion Feeder Instrukcja

4 Października 2024
JANDY

JANDY PSB110 Instrukcja

3 Października 2024
JANDY

JANDY JS100-SM Instrukcja

3 Października 2024
JANDY

JANDY SFTM24-2.0 Instrukcja

3 Października 2024
JANDY

JANDY JS60-SM Instrukcja

3 Października 2024
JANDY

JANDY SFSM-60 Instrukcja

3 Października 2024
JANDY

JANDY AquaSwitch Instrukcja

22 Września 2024
JANDY

JANDY AquaPalm Instrukcja

22 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane