Instrukcja obsługi JANDY SFTM24-2.0

JANDY Niesklasyfikowane SFTM24-2.0

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JANDY SFTM24-2.0 (48 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/48
H0579200_REVD
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and
qualified in pool equipment by the jurisdiction in which the product will be installed where such state
or local requirements exist. The maintainer must be a professional with sufficient experience in pool
equipment installation and maintenance so that all of the instructions in this manual can be followed
exactly. Improper installation and/or operation can create dangerous high pressure which can cause a
catastrophic product failure and/or cause the multiport valve to be blown off possibly causing death,
serious injury or property damage.
Before installing this product, read and follow all warning notices and instructions that accompany this
product. Failure to follow warning notices and instructions may result in death, serious injury or property
damage. Consult Zodiac customer service at 1-800-822-7933 for assistance. Improper installation and/or
operation will void the warranty.
ENGLISH | FRAN ES | ESPAÑOLÇ
INSTALLATION AND
OPERATION MANUAL
Top Mount Sand Filter
Models SFTM22-1.5, SFTM24-2.0
Page 2 ENGLISH Jandy
®
Pro Series Sand Filter SFTM22-1.5, SFTM24-2.0 | Installation & Operation Manual
Section 1. Important Safety Instructions 3 ............................................................
Section 2. Package Contents 4 ...............................................................................
2.1 SFTM22-1.5 .................................................................................................... 4
2.2 SFTM24-2.0 .................................................................................................... 4
2.3 Required Tools/Equipment .............................................................................. 5
Section 3. Equipment Location 5 ............................................................................
3.1 Equipment Pad 5 ................................................................................................
3.2 Filter Location 5 ..................................................................................................
Section 4. Initial Setup 6 ..........................................................................................
4.1 Install Base 6 ......................................................................................................
4.2 Install Hub and Laterals SFTM22-1.5 6 ..............................................................
4.3 Install Hub and Laterals SFTM24-2.0 6 ..............................................................
4.4 Fill With Sand 6 ..................................................................................................
4.5 Assemble Multiport Valve 7 ................................................................................
4.6 Install Multiport Valve 8 ......................................................................................
4.7 Plumbing ......................................................................................................... 8
Section 5. Operation 8 .............................................................................................
5.1 Filter Valve Functions 8 ......................................................................................
5.2 Initial Start up 9 ..................................................................................................
5.3 Operating pressure 9 ..........................................................................................
5.4 Changingtheltersand .................................................................................. 10
5.5 Winterizing .......................................................................................................10
Section 6. Dimensions and Replacement Parts 10 .................................................
6.1 Approximate Dimensions 10 ................................................................................
6.2 Replacement Parts .......................................................................................... 11
Table of Contents
Page 3
ENGLISH
Jandy
®
Pro Series Sand Filter SFTM22-1.5, SFTM24-2.0 | Installation & Operation Manual
SECTION 1. IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
X
MAXIMUM OPERATING PRESSURE OF THE FILTER IS 35 PSI. NEVER SUBJECT THE
FILTER TO ANY OPERATING PRESSURE EXCEEDING 35 PSI
• Do not connect the system to an unregulated city water system or other
external source of pressurized water producing pressures greater than 35 PSI.
• Thislteroperatesunderhighpressure.Whenanypartofthecirculating
system,i.e.,lter,pump,valve(s),etc.isserviced,aircanenterthesystemand
become pressurized when the system is restarted.
• Pressurized air in a system can cause product failure or also cause the dial
valve to be blown off which can result in death, serious personal injury or property damage.
• Tominimizeriskofsevereinjuryordeath,thelterand/orpumpshouldnotbesubjectedtothepiping
pressurization test. Local codes may require the pool piping system to be subjected to a pressure
test.Theserequirementsaregenerallynotintendedtoapplytothepoolequipmentsuchasltersor
pumps. Jandy pool equipment is pressure tested at the factory.
If however, this WARNINGcannotbefollowedandpressuretestingofthepipingsystemmustincludethelterand/
or pump BE SURE TO COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS.
• Check all clamps, bolts, lids, locking devices and system accessories to ensure they are properly
installed and secured before testing.
• RELEASE ALL AIR in the system before testing.
• Water pressure for test must NOT EXCEED 35 PSI
• WatertemperaturefortestmustNOTEXCEED100ºF(38ºC).
• Limit test to 24 hours. After test, visually check system to be sure it is ready for operation.
NOTICE: These parameters apply only to Jandy equipment. For non-Jandy equipment, consult the equipment
manufacturer.
To avoid electrical shock hazard, which can result in serious injury or death:
• Ensure that all electrical to the system is turned off before approaching, inspecting or troubleshooting
any leaking valves or plumbing that may have caused other electrical devices in the surrounding area
to get wet.
• Waterdischargedfromanimproperlypositionedlterorvalvecancreateanelectricalhazardwhich
can cause death, serious injury or property damage.
• Improperdialvalveinstallationcancauseproductfailureoralsocausethelterdialtobeblownoff,
which can result in death, serious personal injury or property damage.
• Never attempt to adjust or remove the dial valve when the pump is running or there is pressure in the
system.thiscancauseproductfailureoralsocausethelterdialtobeblownoff,whichcanresultin
death, serious personal injury or property damage.
CAUTION
• Maintain your pressure gauge in good working order. The pressure gauge is the primary indicator of
howthelterisoperating.
• Creating high vacuum levels can cause the tank vessel to crack and leak with the potential for
property damage.
• Be sure that all provisions for waste water disposal meet local, provincial or national codes. During
any backwash or draining process, 100 gallons or more of water will be discharged. Do not discharge
waterwhereitwillcausefloodingordamage.
• Toavoiddamagingthelaterals(spokes),slowlyaddtheltermediauntilthelateralsarefullycovered.
ConsultInstallationandOperationManualforcompletesandllinginstructionsCrackedorbroken
laterals(spokes)willcausesandtobedischargedtothepool.
Attention installer: This manual contains important information about the installation, operation
and safe use of this product. This information should be given to the owner/operator of this
equipment. SAVE THESE INSTRUCTIONS

Specyfikacje produktu

Marka: JANDY
Kategoria: Niesklasyfikowane
Model: SFTM24-2.0

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JANDY SFTM24-2.0, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane JANDY

JANDY

JANDY Erosion Feeder Instrukcja

4 Października 2024
JANDY

JANDY TruChlor Erosion Feeder Instrukcja

4 Października 2024
JANDY

JANDY PSB110 Instrukcja

3 Października 2024
JANDY

JANDY JS100-SM Instrukcja

3 Października 2024
JANDY

JANDY SFTM24-2.0 Instrukcja

3 Października 2024
JANDY

JANDY JS60-SM Instrukcja

3 Października 2024
JANDY

JANDY SFSM-60 Instrukcja

3 Października 2024
JANDY

JANDY QT Residential Blower Instrukcja

3 Października 2024
JANDY

JANDY AquaSwitch Instrukcja

22 Września 2024
JANDY

JANDY AquaPalm Instrukcja

22 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024