Instrukcja obsługi Jablotron CA-1202 - mode 2
Jablotron
alarm samochodowy
CA-1202 - mode 2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Jablotron CA-1202 - mode 2 (2 stron) w kategorii alarm samochodowy. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
CA-1202 User manual – Mode 2 - 4 / 4 – MHF53400
10. Car battery low voltage reporting
The built-in voltage drop detector can trigger an alarm if an electrical device in
the car is turned on while the car is armed. Also the car alarm checks the voltage
of the car battery. If the voltage is too low (10V) it will notify users via an SMS
message. The car alarm can be backed up by a BB-01 battery. Thus, the car alarm
can send SMS messages (but not work) even when the car battery is
disconnected. The manufacturer recommends regular BB-01 checking once a
year. The battery should be replaced every two years.
11. Limited number of alarms
If any sensor (input) repeatedly triggers alarms then this particular input will be
bypassed automatically after the third alarm (it will remain bypassed until the car
alarm is disarmed).
12. Remote service
When it is necessary to change the basic settings of the alarm like phone numbers
etc you do not need to contact the installer. Instead it is possible to change settings
remotely.
13. Central monitoring station communication
The car alarm allows central monitoring via GPRS data protocol. Please ask your
supplier for details.
14. Roaming
If you travel abroad and your SIM card supports roaming, the car alarm will
work there too (the functions LOCATOR and CREDIT might be not available).
15. LED indicator signals
The LED indicator is used to show
the status of the alarm. Warning! If
the LED indicator starts flashing
fast after the ignition is switched
off, it will not be able to send any
messages nor call in the case of
an alarm.
LED state Meaning
OFF Disarmed
permanently ON Connecting to a GSM network
or a phone call
Regular slow flashing Armed
Interrupted light Car was stopped
(immobilization)
Flashing fast GSM network is not available
Your installer’s contact details:
CA-1202 User manual – Mode 2 - 1 / 4 – MHF53400
The “Athos” CA-1202 GSM car alarm
MODE 2
Thank you very much for buying our CA-1202 car alarm. Now you will always be able to
find where you left your car. Jablotron Ltd.
1. Remote control arming and disarming
The alarm will be armed when the car is locked remotely by the
original remote control and disarmed when the car is unlocked
remotely. If the car is unlocked by key then the alarm will be
triggered. To stop the alarm it is necessary to unlock remotely by the
original remote control. The RC-40 remote control can be used for
remotely operating the gate, garage door etc. Please ask your
installer for detailed information.
2. Acoustic signals The car alarm informs you about its status
by siren chirps. The chirps for arming (1x),
disarming (2x) and arming with the
triggered input (4x) are optional. Warning!
If the GSM network is not available
while the car alarm is being armed it
will not be able to send any messages
nor call in the case of an alarm.
3. Alarm
When an alarm is triggered (the car alarm is armed and an input is triggered), the
siren will sound for 30 sec’s., warning SMS messages will be sent to all phones
(TEL1 to TEL4) and these phones will also be called with a siren sound1. The alarm
can be terminated by unlocking the car remotely by the original remote control or by
SMS instruction. Your mobile will be sent a message stating that the alarm condition
has ended. If the alarm is triggered accidentally (e.g. by unlocking the door with a
key) then in some cases it is necessary to lock the door first and then
unlock by the original remote control to terminate the alarm.
4. Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4) can
operate the alarm remotely. Factory default instruction texts are
shown in the following table. If an SMS is sent from an unauthorized
phone a valid user code must be entered before the instruction (e.g.
USER IMO).
1 If it is activated, then in the case of an alarm all calls are automatically answered
(it is possible to listen and speak to the car remotely).
Chirps Meaning
1x Arming
2x Disarming
3x Disarming after the alarm
4x Arming with the triggered input
6x GSM network is not available
CA-1202 User manual – Mode 2 - 2 / 4 – MHF53400
SMS instruction texts
Default Your text Description
AM ARM 2
DM DISARM 2
IMO STOP (immobilize) the car (after turning
the ignition key off)
UNIMO Unblock (mobilize) the car
STATUS The car alarm will reply with status
information, e.g. „car reports: Time: 27.01.04
13:04, Status: Armed, Unblocked, Ignition off“.
LOCATOR To obtain the car location from the GSM
provider. 2
HELP The car alarm will reply with a brief list of
SMS instructions.
CREDIT To obtain the balance of a prepaid SIM
card if used.2
UC xx...x To change the user code. uuuu is the new
user code, up to 8 characters (A –Z & 0 –
9). The factory default user code is USER
Only basic ASCII can be used in the SMS instruction texts.
Ask the installer to edit the SMS commands for you.
After the HELP command the alarm will reply with the factory default SMS
instructions. The instructions that were modified will not be in the reply.
5. Remote blocking of the car
When the car alarm receives the SMS command IMO it will reply with a
confirmation SMS and block (immobilize) the engine. If the ignition key is on
when the car alarm receives the command IMO, immobilization will occur as
soon as the ignition key is switched off which will be confirmed by SMS.
Unblocking the car is only possible by the SMS instruction UNIMO.
6. Car location
If your GSM provider offers a location service you can obtain the location of the
car by just sending the instruction LOCATOR. The car alarm will reply e.g.
+420603012345 county: Jihocesky, District: Jindrichuv Hradec, Name: Nova Ves nad Luznici.
Distance 5.4 km. E14*52'1"@N48*50'24" + -200m 15:23:01 18.09.01
The alarm can send the location automatically in the case of an alarm or
immobilization by the IMO command3.
7. Remote control by dialing-in
The car alarm can be armed and disarmed remotely by dialing in from an
authorized phone (TEL1 to TEL4). The car alarm will not answer the incoming call,
2 Controlling by dialing in will result only in arming/disarming the alarm but it will not lock/unlock the
doors
3 Must be set by the installer CA-1202 User manual – Mode 2 - 3 / 4 – MHF53400
but when it recognizes your number, it will change status (to Arm or Disarm). Such
remote control is free of charge since the phone is not answered.
Warning, if you dial your car alarm accidentally it can cause the alarm to disarm.
Controlling by dialing in will result only in arming/disarming the alarm but it will not
lock/unlock the doors
8. Phone calls by an installed hands free set
If the HF-03 hands free set is installed, it is
possible to receive and make phone calls via
the car alarm.
Incoming calls – to answer them, press any
button on the RC-40 remote control. By pressing
any button again, the call will be terminated.
To make a call – you can call up to 4
preprogrammed numbers while you are driving.
By pressing one of buttons A, B, 1 or 2 on the
remote control you will dial the corresponding
number (preprogrammed by the installer)
By pressing any button again, the call will be terminated. When armed, all
incoming calls are automatically rejected. If the car is blocked (by the IMO
instruction) all calls are automatically answered (it is then possible to listen to
and to speak to the car remotely).
9. Wireless detectors
It is possible to enroll up to 8 wireless detectors
(movement, glass-break, magnetic etc) from the Jablotron
JA-60 series to protect the area up to 20 meters away from
the car alarm. After arming the car alarm, an exit delay of 20
seconds is provided to all enrolled detectors (the detectors
are ignored during this delay). A 20 second entrance delay
after triggering a detector is provided by the detectors that are
switched to delay mode. In the case of an alarm, the siren will
sound for 30 sec., warning SMS messages (e.g. alarm in
garage) will be sent to all phones (TEL1 to TEL4) and these
phones can also be called with a siren sound. The system
also reports low batteries in a detector by SMS. JA-60P movement
detector
Specyfikacje produktu
| Marka: | Jablotron |
| Kategoria: | alarm samochodowy |
| Model: | CA-1202 - mode 2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Jablotron CA-1202 - mode 2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje alarm samochodowy Jablotron
23 Września 2024
22 Września 2024
13 Września 2024
2 Września 2024
Instrukcje alarm samochodowy
- alarm samochodowy HP
- alarm samochodowy Cobra
- alarm samochodowy Waeco
- alarm samochodowy Viper
- alarm samochodowy Gemini
- alarm samochodowy Technaxx
- alarm samochodowy Audiovox
- alarm samochodowy Spy
- alarm samochodowy GT
- alarm samochodowy Clifford
Najnowsze instrukcje dla alarm samochodowy
1 Października 2024
1 Października 2024
1 Października 2024
27 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024