Instrukcja obsługi Intel SSD DC S3710

Intel Solid state drives (ssd) SSD DC S3710

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Intel SSD DC S3710 (12 stron) w kategorii Solid state drives (ssd). Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Intel® Solid-State Drive

Installation Guide 1

Intel® Solid-State Drive

Installation Guide

Overview

Installing an Intel SSD consists of three main steps:

Before you Begin

•Download and save the Intel Data Migration Software to your current storage device:

http://www.intel.com/go/ssdinstallation

•Confirm you have the necessary hardware for installation:

Note: Contents vary based on package purchased.

This guide explains how to install an Intel® Solid-State Drive

(Intel® SSD) in a SATA-based desktop or notebook computer.

The instructions include migrating your data from your current

storage device (such as a hard disk drive) to your new Intel SSD

using Intel® Data Migration Software.

1. Connect the Intel SSD to your computer.

2. Migrate your data from your current storage device to your new Intel SSD.

3. Swap the placement of your current storage device with your new Intel SSD.

Hardware item Required for

1. SATA-to-SATA interface cable Desktop computers

2. SATA power adapter Desktop computers without a SATA power cable

3. 3.5-inch mounting adapter and screws Desktop computers with 3.5-inch drive bay

4. USB-to-SATA cable Notebook computers

5. Drive sleeve Notebook computers (optional - for use with your old

storage device after the SSD is installed)

6. Phillips screwdriver Most computers

13 4 5 6

Intel® Solid-State Drive

2 Installation Guide

Intel® Solid-State Drive

SSD Handling Precautions

Observe the following before beginning the installation:

•Keep the SSD in the protective anti-static container until you are ready to install.

•Handle the SSD with care. Do not touch the gold connectors.

•To minimize static electricity, touch the computer case before handling the SSD.

•Do not remove the encasement or disassemble the SSD; these actions void the SSD warranty.

This step explains how to connect the Intel SSD to your computer in preparation for migrating

your data. Note that your current storage device remains installed until the final step of the

installation, “Swap Your Drives” on page 8.

Follow the steps for your platform:

—“Desktop Computers” (next section)

—“Notebook Computers” on page 4

Desktop Computers

1. If your desktop computer has a 3.5-inch drive bay, attach the Intel SSD to the mounting

adapter. (This helps the SSD fit securely in a drive bay.) If your desktop computer has a 2.5-

inch drive bay, you do not need to attach the mounting adapter. Go to step 2 in this section.

a. With the SSD right side up (Intel logo showing), place the Intel SSD on the mounting

adapter. Make sure the edge of the Intel SSD (with connectors) aligns with the edge of the

mounting adapter. See Figure 1.

b. Turn the SSD and mounting adapter over and insert one screw in each mounting hole on the

bottom of the mounting adapter. See Figure 1.

Figure 1. Place and attach Intel SSD on mounting adapter

2. Power off the computer. Keep the power cable connected.

3. Remove the computer case.

Refer to your computer documentation to determine how to safely remove the computer case.

1. Connect the Intel SSD to your Computer

Intel® Solid-State Drive

Installation Guide 3

Intel® Solid-State Drive

4. Connect one end of the SATA-to-SATA interface cable to a SATA interface connector or

SATA host adapter on your computer motherboard and connect the other end to the

Intel SSD. See Figure 2.

Note: The SATA cable connectors are keyed to ensure correct orientation and contain a

locking bracket for securing in place. Insert cables gently. Do not use excessive force.

5. Locate an available SATA power cable (connected to the internal computer power supply) and

connect it to the Intel SSD. See Figure 2.

Note: Most computers have an available SATA power cable. If your computer does not have a

SATA power cable and instead uses a 4-pin power connector, use a SATA power adapter.

(The SATA power adapter comes with certain packages or can be purchased separately.)

Figure 2. Connect SATA interface and power cables

6. Slide the connected Intel SSD with mounting adapter into an available 3.5-inch drive bay, or

secure the Intel SSD to the computer by inserting one screw in each of the side-mounting or

bottom-mounting holes.

7. Power on the computer and wait for the operating system to recognize the Intel SSD.

A message appears when the SSD is recognized.

The Intel SSD is now connected. Proceed to “Migrate Your Data” on page 5.

1. SATA-to-SATA interface cable: Connect to SATA interface connector on computer motherboard and to Intel SSD.

2. SATA power cable (or SATA power adapter): Connect from power supply to Intel SSD.

Specyfikacje produktu

Marka:	Intel
Kategoria:	Solid state drives (ssd)
Model:	SSD DC S3710
Kolor produktu:	Srebrny
Wysokość produktu:	7 mm
Szerokość produktu:	- mm
Głębokość produktu:	- mm
Waga produktu:	82 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Obsługiwane systemy operacyjne Windows:	Tak
Wewnętrzny:	Tak
Zakres temperatur (eksploatacja):	0 - 70 °C
Szyfrowanie / bezpieczeństwo:	256-bit AES
Pojemność dysku:	200 GB
Szybkość przesyłania danych:	6 Gbit/s
Standardowe rozwiązania komunikacyjne:	Serial ATA III
MTBF (Średni okres międzyawaryjny):	2000000 h
Rozmiar kieszeni dysku SSD:	2.5"
Litografia procesora:	20 nm
Pojemność pamięci SSD:	200 GB
Prędkość odczytu z nośnika:	550 MB/s
UBER:	< 1 per 10^17 bits read
Typ pamięci:	MLC
zużycie energii- tryb włączenia:	4 W
Prędkość zapisu nośnika:	300 MB/s
Litografia:	20 nm
Segment rynku:	Serwer
Wibracje podczas pracy:	2.17 G
Wibracje podczas przechowywania:	3.13 G
Pobór mocy (bezczynny):	0.6 W
Opóźnienie zapisu:	66 µs
Opóźnienie odczytu:	55 µs
Technologia Enhanced Power Loss Data Protection:	Tak
Monitoring temperatury SSD:	Tak
Ochrona danych End-to-End Data Protection:	Tak
Random write (100% span):	43000 IOPS
Nazwa produktu:	Intel SSD DC S3710 Series (200GB, 2.5in SATA 6Gb/s, 20nm, MLC)
Status:	Launched
Rodzina produktów:	Centrum danych SSD
Urodzony:	Q1'15
Data premiery:	2015-01-27T00:00:00
SSD ARK ID:	82939
Seria produktów:	Intel DC S3710
Nazwa kodowa produktu:	Haleyville
Odczyt sekwencyjny:	550 MB/s
Szybkość zapise sekwencyjnego:	300 MB/s
Szyfrowanie sprzętowe dysku SSD:	AES 256 bit
Zużycie prądu dysku SSD (tryb pracy):	4.0W
Zużycie prądu dysku SSD (tryb bezczynności):	0.6W
Dysk SSD - wstrząsy:	1000 G/0.5ms
SSD jest przeznaczona do:	Centrum danych
Intel® High Endurance Technology (HET):	Tak
URL do instrukcji:	http://www.intel.com/content/www/us/en/solid-state-drives/ssd-dc-s3710-brief.html
Wytrzymałość dysku SSD:	3.6PB
Waga dysku SSD:	82 grams g