Instrukcja obsługi Indesit YT M11 82SS X

Indesit Suszarka bębnowa YT M11 82SS X

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Indesit YT M11 82SS X (4 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

THANK YOU FOR BUYING AN INDESIT PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.indesit.eu/register

PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.

Quick guide

Before using the appliance carefully

read the Safety Instruction.

CARE LABEL

Always check the care labels, especially when placing garments in

the tumble dryer for the  rst time. Below are the most commonly

used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

DAILY USE

Doing this will keep your machine working at its BEST:

- remember to empty your water tank after each drying

cycle.

- remember to clean your lters after each drying cycle.

Refer to the Care & Maintenance section.

1. Plug the dryer into the power supply socket.

2. Open the door and load garments; always refer to instructions

on clothing labels and the max loads indicated in the

programme section. Empty pockets. Make sure garments do not

get caught between the door and/or the door lter. Do not load

items that are dripping wet. Do not tumble dry large, very bulky

items. For optimal drying result, garments should be loaded one

by one.

3. Close the door.

4. Press the "On/O" button.

5. Select the most suitable programme

for the type of fabric in

that load.

6. Select the options, if necessary.

7. Press the "

Start/Pause"

button to begin drying.

8. At the end of the drying cycle, a buzzer will beep. An indicator

on the control panel signals the end of the cycle. Turn the

machine o by pressing the "On/O" button, open the door and

pull the clothing immediately out to prevent the formation of

creases on laundry.

If the machine is not switched o manually, after about a quarter

of an hour from the end of the cycle , the appliance turns o

automatically to save energy.

Note that some programme/option accords with "Crease Care"

system. This means that for some hours, after the end of the

drying cycle, the drum rotates at regular intervals to prevent the

formation of creases.

Note that some models perform a nal cool tumble phase, for this

reason the fabrics may not feel hot.

In case of power failure, it is necessary to press the "Start/Pause"

button to restart the cycle.

PUSH & GO

This function serves to start a cycle, after machine switching on,

without abling ny urther tton n/or nob en a f bu a k (the ogramme pr

PUSH & GO will be deactivated instead).

It is always necessary to follow the points 1, 2, and 3 concerning

the daily use.

To start the cycle PUSH & GO, keep the button pressed. The light on

signals that the cycle is started. The cycle is suitable for cotton and

synthetic textiles. Max. load 4 kg. (Cycle ration 0’). du 12

If the door is opened during the cycle, to restart it, close the door and

press the button START/PAUSE. This programme does not allow to

set other options.

Opening the door during the cycle

The tumble dryer door can be opened at any time during the cycle

to check progress and remove any garments already dry.

However, since opening the door can extend the drying time, the

recommendation is to keep the door closed throughout the cycle

process to save time and energy.

After closing the door, press the "Start/Pause" button within 15

minutes to resume the machine operation.

FIRST TIME USE

Make sure that the water tank is correctly inserted. Make sure

that the drain hose on the back of the dryer is properly xed,

either to the dryers's water tank or to the domestic sewage

system.

The dryer must be installed in a room with a temperature

ranging between 5°C and 35°C to ensure proper operation.

Before you use your dryer ensure that it has been in a upright

position for at least 6 hours.

CONTROL PANEL

1 ON/OFF button (hold for Reset)

2 Programme selection knob

3 Start/Pause

4 Push&GO

Options buttons*

5 Dryness level

6 Start delay

7 Timed drying

8 Cycle end

9 Light drying (hold for Key Lock)

10 Crease care ( hold for Mute)

*Note: some models may have the wording in full instead of the icons.

INDICATORS

Dryness level: Iron dry - Hanger dry - Cupboard dry -

Extra dry

Cycle phase: END Dry - Cool tumble - End of cycle

Empty water tank - Clean door lter - Clean bottom lter

Refer to Troubleshooting section: Failure call After-sales Service

5 6 7

DEMO

3’’

*MAX LOAD 8 Kg (Dry load)

OPTIONS

These buttons allow you to personalise the selected programme

according to personal requirements.

Not all options are available for all programmes. Some options

may be incompatible with ones you have previously set; if so,

you will be alerted by the buzzer and/or blinking indicators.

If the option is available, the option indicator will stay on. The

programme may retain some options selected in previous drying

cycles.

Dryness level

Press the related button several times to obtain a dierent

level of residual moisture on garments. An indicator signals the

level being selected.

Iron Dry: very delicate drying. Items will be more easily

ironed immediately after the cycle.

Hanger dry: a level intended for delicate garments ready to

be hanged.

Cupboard dry: the garments are ready to be folded and put

away.

Extra dry: used for garments to be worn at the end of the

cycle.

Timed drying

This option is to manually set the drying time. Press the

corresponding button to set the required time for drying. An

indicator on the control panel signals the time being selected.

Start delay

This option is for delaying the start of the cycle. Press the

corresponding button several times to nd the required delay.

Once the max time is reached, the option is reset by pressing

the button again. An indicator on the control panel signals the

time being selected. After pressing the "Start/Pause" button, the

machine signals the time remaining to the start of the cycle. If the

door is opened, press the "Start/Pause" button once the door has

been closed.

Mute

This option turns o all sounds of control panel. Only

warnings remain active.

• to activate the option, keep the button pressed until the indicator

goes on.

• to disable the option, keep the button pressed until the indicator

goes o.

Cycle end

This option activates a prolonged buzzer at the end of the

cycle. Enable it if you are not sure to hear the normal sound at the

end of the cycle. This option remains in memory if selected in the

previous drying.

Key lock

This option makes all machine controls inaccesible, except the

button On/O. When the machine is on:

• to activate the option, keep the button pressed until the indicator

goes on.

• to disable the option, keep the button pressed until the indicator

goes o.

This option remains in memory if selected in the previous drying.

Crease care

This option add a crease treatment at the end of the cycle by

means of a periodic rotation of the drum (duration up to 10 hours). It

is particularly suitable when it is not possible to remove the laundry

as soon as the drying ends. If this option is used together with the

Start Delay, the crease treatment is added also in the Start Delay

phase. This option remains in memory if selected in the previous

drying.

Light dry

Enables a more gentle treatment of the laundry by reducing

the drying temperature.

PROGRAMMES

The duration of these programs will depend on the size of the

load, types of textiles, the spin speed used in your washer and

any extra options selected. In machines equipped with display,

the duration of the cycles is shown on the control panel. The

remaining time is constantly checked and adjusted during the

drying cycle to show the best possible estimate.

Option to use - If all your loads on Automatic Cycles are

consistently less dry or more dry than you would like, you may

increase or decrease the dryness level using the specic option.

Eco kg Max*

This is the most ecient programme in terms of energy

consumption and is suitable for drying normal wet

cotton laundry. The values on the Energy Label are based on this

programme.

NOTE: For optimal energy eciency this cycle by default is set up to

"Cupboard Dry" level. For a higher dryness level we suggest using

the Cotton cycle.

Cotton kg Max*

Cycle suitable for drying all types of cotton, ready to be

placed in the cupboard.

Mixed kg 4

This programme is ideal for drying cotton and synthetic

fabrics together.

Synthetics kg 4

For drying laundry made of synthetic bres.

Mini synthetics kg 2

Eco-drying of small laundry loads.

Delicates kg 2

For drying delicate laundry requiring a gentle treatment.

Wool kg 1

Programme for drying wool clothing. It is advisable to turn

the garments inside out before drying. Leave to dry naturally the

heaviest edges that are still damp.

Refresh

A short programme suitable for refreshing bres and

garments by means of fresh air. Do not use with garments

that are still wet. It can be used on with any load size but is

more eective with small loads. The cycle duration is about 20

minutes.

Jeans kg 3

For drying cotton jeans-wear and garments made of robust

cotton, like denim, such as trousers and jackets.

Shirts kg 3

This is a programme for Shirts made from cotton or cotton

blend/synthetics.

Duvet

Programme intended to dry bulky garments, as single duvet.

Baby kg 2

A programme intended to dry garments and linen of

new-born babies (cotton and chenille), as well as delicate

garments. Do not dry garments having plastic covering.

Sport kg 4

For drying sports garments made of synthetics or cotton

blends.

Smart iron

This cycle relaxes bres, thus making ironing and folding

easier. Suitable for small load of damp or dry cotton and cotton

blend fabrics. Not for wet items.

45’

Xpress 45' kg 1

This is a quick timed programme, ideal for drying garments

spun at high speed in the washing machine, e.g. the shirts used

in a working week.

Quick guide

Power consumption

o-mode (Po) - Watts 0.42

left-on mode (Pl) - Watts 2.00

Programmes MinutesKg kWh

Eco* 8 1.85 194

Eco 4 1.14 135

Synthetics 4 0.73 95

* This is the reference programme for the energy label and suitable to

dry normal wet cotton laundry. This is the most ecient programme

in terms of energy consumption for drying wet cotton laundry.

(Standard/Default starting conguration).

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be cleaned

with a damp cloth.

• Clean the front air intake grille regularly (every 6 months) with

a vacuum cleaner to remove any lint, u or dust deposits.

Furthermore, remove any lint deposits from the lters area,

using a vacuum cleaner every so often.

• Do not use solvents or abrasives.

TRANSPORT AND HANDLING

Never lift the dryer by holding it at the worktop.

1. Unplug the dryer.

2. Remove the water from the water tank completely.

3. Make sure that door and water tank are properly closed.

4. If the drain hose is connected to your drainage system,

re-connect it to the back of the dryer (see "Installation" section

in the Safety Instruction guide).

A B

C1 C2 C3

C4 C5 C6

CLEANING AND MAINTENANCE

WARNING: unplug the dryer during the cleaning and

maintenance procedures.

Emptying the water tank after each cycle (see Fig. A).

Pull the container out of the dryer and empty it into a sink or other

suitable drain, then place it back properly. Do not use the dryer

without having inserted the container back in place.

Cleaning the door lter after each cycle (see Fig. B).

Pull the lter out and clean it by removing the lint from the lter

surface under running water or using a vacuum cleaner. For optimal

performance, dry up all the lters before inserting them back in

place. Do not use the dryer without having reinserted the lter

in place.

Remove the door lter as described below:

1. Open the door and pull upwards.

2. Open the lter and remove lint from all its parts. Replace it

correctly. Ensure it is completely inserted ush with the dryer seal.

Cleaning the bottom lter when the relevant indicator

turns on (see Fig. C).

Pull the lter out and remove the lint from its surface by washing

it under runing water or by using a vacuum cleaner. However, it

is advisable to clean this lter after each cycle to optimise drying

performance. Do not use the dryer without having reinserted the

lter in place.

Remove the bottom lter as described below:

C1. Open the bottom cover; take the handle and pull the lter

out.

C2. Open the rear side of the lter and remove the lint from the

inner surface of the mesh.

C3/C4. Check the bottom lter chamber every month. If you

see residual lint accumulated on the metal ns, clean it with a

vacuum cleaner, using a nozzle with a brush.

It's crucial to do vertical movements, you may destroy the

component if you try to clean it in horizontal direction. Avoid the

direct contact of the hand with the ns - risk of cut.

C5. Close the rear side of the lter and place it back by checking it

is perfectly integrated into its seat, then lower the lter handle.

C6. Close the bottom cover.

Make sure the air intake is free.

The lters are essential parts for drying. They are intended

to collect the lint formed during the drying process. In case

of clogged lters, the air ow inside the dryer would be

seriously aected: the drying times would be longer, the

energy consumption would increase and the dryer could be

damaged. If these procedures are not carried out properly,

the dryer may not start.

Heat Pump System

The heat pump contains uorinated greenhouse gases,

contained in a hermetically sealed unit. This sealed unit contains

0.18 kg of the R134a gas. GWP = 604 (1 t CO).

PRODUCT DESCRIPTION

1. Water Tank

2. Air Intake

3. Bottom lter

4. Door lter

NOTE: After cleaning the lters the relevant indicator remains

on; this is normal, it will disappear when you start a new drying

cycle.

Specyfikacje produktu

Marka:	Indesit
Kategoria:	Suszarka bębnowa
Model:	YT M11 82SS X

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Indesit YT M11 82SS X, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Suszarka bębnowa Indesit

Indesit YT M11 92B X Instrukcja

7 Stycznia 2025

Indesit YT M11 82SS X Instrukcja

7 Stycznia 2025

Indesit C YD A81 WWGL UK Instrukcja

7 Stycznia 2025

Indesit YT M11 82B X UK Instrukcja

2 Stycznia 2025

Indesit BI WDIL 861485 UK Instrukcja

30 Grudnia 2025

Indesit IDV 75 B K (UK) Instrukcja

14 Października 2024

Indesit YT M11 82 X UK Instrukcja

14 Października 2024

Indesit Ecotime IWDC 65125 S UK Instrukcja

9 Października 2024

Indesit BI WDIL 75148 UK Instrukcja

8 Października 2024

Indesit BDE 86436 WV UK Instrukcja

8 Października 2024

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Gram TLS 7853-92 Instrukcja

8 Stycznia 2025

Hisense WF3V843BB Instrukcja

8 Stycznia 2025

Miele TEC374WP Instrukcja

8 Stycznia 2025

Yamazen ZFE-W800 Instrukcja

7 Stycznia 2025

Hyundai DHN8MY Instrukcja

7 Stycznia 2025

Siemens WQ45H2B5NL Instrukcja

6 Stycznia 2025

Smeg SACD8 Instrukcja

5 Stycznia 2025

Whirlpool FFT M11 9X2BS BE R Instrukcja

5 Stycznia 2025

Whirlpool FFT M11 8X2BS BE R Instrukcja

5 Stycznia 2025

Whirlpool FT M22 8X3B EU Instrukcja

5 Stycznia 2025