Instrukcja obsługi Indesit XWDE 861480
Indesit
Był/Droogcombi
XWDE 861480
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Indesit XWDE 861480 (56 stron) w kategorii Był/Droogcombi. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/56
1
GB
Washer-dryer
Instructions for use
! This symbol reminds you to read this instruction manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washer-dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and options, 9-10
Table of wash cycles
Wash options
Push&Wash+Dry
Detergents and laundry, 11-12
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13
Service, 14
XWDE 861480
English,1
GB NL
Nederlands,15
TR
Türkçe,29
RO
Română,43
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washer-dryer is
sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its packaging.
2. Make sure that the washer-dryer has not been
damaged during the transportation process. If
it has been damaged, contact the retailer and
do not proceed any further with the installation
process.
3. Remove the 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washer-dryer needs to
be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
perfectly level,
compensate for
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive
noise and prevent it from shifting while it is
operating. If it is placed on carpet or a rug, adjust
the feet in such a way as to allow a sufficient
ventilation space underneath the washer-dryer.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it
to a cold water tap
using a ¾ gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the inlet
hose to the washer-
dryer by screwing it
onto the corresponding
water inlet of the
appliance, which is
situated on the top
right-hand side of
the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
• the socket is earthed and complies with all
applicable laws;
• the socket is able to withstand the maximum
power load of the appliance as indicated in the
Technical data table (see opposite);
• the power supply voltage falls within the values
indicated in the Technical data table (see
opposite);
• the socket is compatible with the plug of the
washer-dryer. If this is not the case, replace
the socket or the plug.
! The washer-dryer must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washer-dryer has been installed, the
electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
65 - 100 cm
Technical data
Model XWDE 861480
Dimensions
width 59.5 cm
height 85 cm
depth 60,5 cm
Capacity
from 1 to 8 kg for wash
programme
from 1 to 6 kg for the drying
programme
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed up to 1400 rotations per
minute
Energy ra-
ted
programmes
according to
regulation
EN 50229
wash: programme 8; tem-
perature 60°C; using a load
of 8 kg.
drying: the smaller load
(2kg) must be dried by se-
lecting the “ ” dryness le-
vel. The load must consist of
3 sheets, 2 pillowcases and
1 hand towel; the remainder
of the load must be dried by
selecting the “ ” dryness
level.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle
“Auto Clean” (see “Cleaning the washer-dryer”).
Specyfikacje produktu
| Marka: | Indesit |
| Kategoria: | Był/Droogcombi |
| Model: | XWDE 861480 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Indesit XWDE 861480, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Był/Droogcombi Indesit
4 Lipca 2024
2 Lipca 2024
2 Lipca 2024
2 Lipca 2024
2 Lipca 2024
1 Lipca 2024
28 Czerwca 2024
Instrukcje Był/Droogcombi
- Był/Droogcombi Bauknecht
- Był/Droogcombi Electrolux
- Był/Droogcombi Beko
- Był/Droogcombi Bosch
- Był/Droogcombi Candy
- Był/Droogcombi Whirlpool
- Był/Droogcombi Hoover
- Był/Droogcombi Siemens
- Był/Droogcombi Grundig
- Był/Droogcombi Hotpoint Ariston
- Był/Droogcombi Zanussi
- Był/Droogcombi Privileg
- Był/Droogcombi Zanussi-electrolux
- Był/Droogcombi Luxor
Najnowsze instrukcje dla Był/Droogcombi
26 Września 2024
26 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
24 Września 2024
20 Września 2024
4 Września 2024
4 Września 2024