Instrukcja obsługi Imou Cube 4MP
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Imou Cube 4MP (3 stron) w kategorii kamera. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/3
Installing Camera
Make sure the mounting surface is strong enough to hold at least
three times of the device weight.
Expansion Bolt
Camera
About the Guide
- This quick start guide is for reference only. Minor difference might
be found in user interface.
- All the design and software here are subject to change without
prior written notice.
- All trademarks and registered trademarks mentioned are the
properties of their respective owners.
- Please visit our website or contact your local service engineer for
more information.
- If there is any uncertainty or controversy, please refer to our final
explanation.
Alarm Input/output
The camera can connetct to external alarm input/outpiut device
through digital input/output.
Device collects different states of alarm input port when the input
signal is idling and being grounded.
Device collects logic "1" when input signal is connecting to +3V to
+5V or idling.
Device collects logic "0" when input signal being grounded.
Mode A: Level application. Alarm outputs high and low level, and the
alarm outlet is OD, which requires external pull-up resistance (10K
Ohm typical) to work. The maximum external pull-up level is 12V,
maximum port current is 300mA and the default output signal is high
level (external pull-up voltage). The default output signal switches to
low level when there is alarm output (As long as the operating current
below 300mA, the output low level voltage is lower than 0.8V).
Step 1
Step 2
Connect alarm output device to the alarm output end of the I/O
port. The alarm output is open-drain output, which works in the
following modes.
Mode B: Switch application. Alarm output is used to drive
external circuit, the maximum voltage is 12V and the maximum
current is 300mA. If the voltage is higher than 12V, please use
an additional electric relay.
Step 3
Log in web interface, and configure alarm input and alarm output
in alarm setting.
The alarm input in the web interface is corresponding to the alarm
input end of the I/O port. There will be high level and low level
alarm signal generated by the alarm input device when alarm
occurs, set the input mode to "NO" (default) if the alarm input
signal is logic "0" and to "NC" if the alarm input signal is logic "1".
The alarm output in the web interface is corresponding to the
alarm output end of the device, which is also alarm output end of
the I/O port.
Loosen the adjust knob and adjust the camera to a
proper surveillance position as needed.
Secure the adjust knob to fix the camera.
Note: Step 1
Step 2
Step 3
Step 4
Step 5
Drill screw holes on the mounting surface as the
positioning map shows, and then put in the expansion
bolts.
Attach the camera pedestal to the mounting
surface with the self-tapping screws.
Connect the cable and start the camera.
Connecting
Connect alarm input device to the alarm input end of the I/O port.
See the following picture.
Adjust Knob
Self-tapping Screw
Mounting Surface
Positioning Map
Introduction
Note: Press and hold the
reset
button for 10 s to reset the camera.
Camera
The pattern of the LED indicator is included in the following table.
LED Indicator Status
Green light flashing
Green light on
Red light flashing
Green and red light
flashing alternately
Powered off/LED turned off
Rebooting after reset
Booting
Device malfunction
Waiting for network
Operating properly
Network connection failed
Off
Red light on
Firmware updating
QSG ×1Camera ×1 Positioning Map ×1
Power Adapter ×1 Screw Package×1
Version 1.0.0
Quick Start Guide
Built-in Mic
Indicator Light
Ethernet Port
Reset Button
Power Port
Built-in Speaker
PIR Detector
IR LED
Micro SD Card Slot
Digital Input/Output
Device Status
With Imou AppOperating
Step 1
Step 3
Connect the camera to power source with the power adapter.
Scan the following QR code or search “Imou” in Google Play or App
Store to download and install Imou App.
Run Imou App, and then register an account for the first use.
Step 2
Note: If you have installed the App, update it to the latest version.
Mounting Surface
Step 5
Step 4
Do the following operations to finish adding camera.
Wait for booting to be finished, and then the camera indicator flashes
with green light.
Note
If the Wi-Fi network has changed or the indicator status goes
wrong, reset the camera, and then do step 5 to add it again.
If you have more than one camera, do step 5 to add them one
by one.
Select Wi-Fi
Wi-Fi XXXXXX1
Wi-Fi XXXXXX2
Wi-Fi XXXXXX3
...
Wi-Fi Password
Specyfikacje produktu
| Marka: | Imou |
| Kategoria: | kamera |
| Model: | Cube 4MP |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Imou Cube 4MP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje kamera Imou
7 Października 2024
5 Października 2024
29 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
24 Września 2024
24 Września 2024
Instrukcje kamera
- kamera Sony
- kamera Samsung
- kamera Leica
- kamera Logitech
- kamera Joy-It
- kamera TP-Link
- kamera Philips
- kamera SilverCrest
- kamera Acer
- kamera Hikvision
- kamera Panasonic
- kamera Canon
- kamera Medion
- kamera Lenco
- kamera Fujifilm
- kamera Ring
- kamera Blaupunkt
- kamera Casio
- kamera Sigma
- kamera HP
- kamera Prixton
- kamera SJCAM
- kamera Swann
- kamera Nikon
- kamera Kodak
- kamera Scosche
- kamera DJI
- kamera Zenit
- kamera Gembird
- kamera Minox
- kamera Cobra
- kamera JVC
- kamera Trust
- kamera Fimi
- kamera AgfaPhoto
- kamera Vimar
- kamera Dahua Technology
- kamera Kyocera
- kamera Ricoh
- kamera Rollei
- kamera Velleman
- kamera Pyle
- kamera Vtech
- kamera Speco Technologies
- kamera ARRI
- kamera Fluke
- kamera Olympus
- kamera Avaya
- kamera National Geographic
- kamera Maginon
- kamera SPC
- kamera Polaroid
- kamera Konica Minolta
- kamera Sanyo
- kamera Red Digital Cinema
- kamera Oregon Scientific
- kamera Lorex
- kamera Bresser
- kamera Hama
- kamera GoPro
- kamera Denver
- kamera Pentax
- kamera Bushnell
- kamera Marshall Electronics
- kamera Hitachi
- kamera Emerson
- kamera SereneLife
- kamera AVerMedia
- kamera Genius
- kamera Levenhuk
- kamera BenQ
- kamera Trevi
- kamera Technaxx
- kamera Lexibook
- kamera Hanwha
- kamera Blackmagic Design
- kamera Foscam
- kamera Lumens
- kamera Dörr
- kamera POV
- kamera Elmo
- kamera UniView
- kamera Vivitar
- kamera PTZ Optics
- kamera Agfa
- kamera Argus
- kamera Easypix
- kamera Celestron
- kamera Yashica
- kamera Flir
- kamera Daitsu
- kamera Arlo
- kamera Nest
- kamera Intel
- kamera Mamiya
- kamera Fuji
- kamera Minolta
- kamera EverFocus
- kamera RunCam
- kamera SeaLife
- kamera Burris
- kamera Meade
- kamera Contax
- kamera Exakta
- kamera Digital Watchdog
- kamera MuxLab
- kamera AViPAS
- kamera ZeissIkon
- kamera Spypoint
- kamera HOLGA
- kamera Praktica
- kamera Hasselblad
- kamera Kogan
- kamera Getac
- kamera Brinno
- kamera Z CAM
- kamera Ergoguys
- kamera Strex
- kamera General Electric
- kamera Leotec
- kamera Leitz Focomat IIc
- kamera Cosina
- kamera Videology
- kamera InfiRay
- kamera Pelco
- kamera Videotec
- kamera Cambo
- kamera Kobian
- kamera Kyocera Yashica
- kamera Konica
- kamera Akaso
- kamera Seek Thermal
- kamera Aida
- kamera Ikegami
- kamera Ikelite
- kamera Adeunis
- kamera Hoppstar
- kamera Moultrie
- kamera PatrolEyes
- kamera Camouflage
- kamera HuddleCamHD
- kamera Aplic
- kamera Linhof
- kamera GoXtreme
Najnowsze instrukcje dla kamera
15 Października 2024
15 Października 2024
13 Października 2024
11 Października 2024
10 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024