Instrukcja obsługi Illustra IPS02-B15-OI03
Illustra
Bewakingscamera
IPS02-B15-OI03
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Illustra IPS02-B15-OI03 (8 stron) w kategorii Bewakingscamera. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
2. Attaching the camera to the mounting arm (continued)
B. Place the camera onto the hinge (1) (Figure 5) and release the pin so that
the camera is attached to the mounting arm plate.
Figure 5
C. See step 4 to connect the power cable and then continue on at step D.
D. Flip the camera so that it sits properly on the mounting plate and arm
secure it to the mounting arm plate th the four T10 screws (1) (Figure wi 6).
Quick Start Guide
( - -8200 1630 04_A0)
Illustra Pro Gen 3 Bullet Cameras
In the box
4 x plastic screw anchors (use on masonry walls and wood)
Phillips pan head tapered screw TP6x32 (use on masonry wall and wood) 4 x mm
4 x Phillips pan head tapered screw M5x8mm (Adaptor plate base)
Printed Quick Start Guide 1 x
Printed regulatory document 1 x
NTSC / PAL output female BNC cable 1 x
1 x RJ45 Connector
1 x Terminal block
Mounting arm 1 x
Mounting template 1 x
1 x Desiccant bag
4 Toggle screw (Expansion Bolt) x
1 x T10 security Torx wrench
1 x Universal electrical box mounting plate (IPSMDEBPLATE)
1 x Pendant / pole mount adaptor
1 x rubber plug (with two holes) and 1 rubber pin
1 x rubber plug (with no holes)
1 x 4mm Allen key
Installation tools
1 x Drill
1 x T10 security Torx wrench
1 x Phillips screw driver
Quick reference
Default IP: 192.168.1.168 (DHCP enabled)
Default Username and Password: admin
Note: You can attach the camera to a surface or directly to a pendant or pole 1 ½ ‘’
Male NPT pipe using the pendant / pole mount adaptor. (The pendant / pole mount
adaptor can be attached to a standard 1 ½‘’ NTP pipe using threads or set screws).
Note: To ensure optimal lens performance, JCI recommends using the automated
lens calibration feature within the web GUI following initial camera installation.
1. Attaching the mounting arm to a surface
A. Place the mounting template provided on the surface and drill four 8mm
(0.3 inch) holes. 14
B. sert the four screw anchors into the four holes on the surface. In
C. After passing all required cabling through the mounting arm, place the
mounting arm (1) (Figure 1) on the surface and align the four holes on the
mounting arm (2) (Figure 1) with the four screw anchors or expansion bolts
on the surface (3) (Figure 1).
D. Insert the rubber plug into the top hole on the mounting arm (4) (Figure 1) to
prevent water from entering the mounting arm.
Figure 1
1. Attaching the mounting arm to a surface (continued)
E. Securely attach the mounting arm to the surface with the four TP6x32mm
screws (1) (Figure 2).
Figure 2
F. Insert the Ethernet cable through the waterproof rubber (1) (Figure 3) and if
not using both grommet holes insert the rubber pin (2) (Figure 3) into the
waterproof rubber.
G. Insert the waterproof rubber onto the mounting arm plate. (3) (Figure 3).
1. Attaching the mounting arm to a surface (continued)
Figure 3
2. Attaching the camera to the mounting arm
A. Push the pin (1) (Figure. 4) from the mounting arm hinge.
Figure 4
2. Attaching the camera to the mounting arm (continued)
Figure 6
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
A. Place the pendant/pole mount adaptor (1) (Figure 7) around a standard 1
½‘’ Male NPT threaded water pipe (2) (Figure 7) and securely attach the
two M3x0.5P (L = 6mm) screws on the pendant mount adaptor with the T10
security Torx wrench.
Figure 7
Table 1: Camera buttons / connections
Button / connections Description
Alarm in 1
Alarm in 2
Alarm out
COM
Audio line in
Audio line out
Ground
Analog out cable connection
Micro SD card slot
AC 24 V
AC power connection
USB cable connection
Reboot button (Hold for 10 seconds)
Reset button (Hold for 20 seconds)
RJ45 Ethernet cable connection / PoE+
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
(continued)
B. Unscrew the M5 Hex socket cap screw (1) (Figure 8) to remove the
mounting arm plate (2) (Figure 8) from the mounting arm (3) (Figure 8).
Figure 8
C. Push the pin (1) (Figure 9) and place the camera onto the hinge and release
the pin so that the camera is attached to the mounting arm plate.
Figure 9
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
(continued)
D. See step 4 to connect the power cable and then continue on at step E.
E. Securely attach the mounting arm plate to the camera with the four T10
screws (1) (Figure 10) on the mounting arm plate.
Figure 10
F. Place the mounting plate arm and camera into the pendant mount adaptor
(1) (Figure 11) and securely attach the two M3x0.5P (L = 6mm) screws with
the T10 security Torx wrench.
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
(continued)
Figure 11
4. Connecting the power cable to the power plugs
A. Connect the power cable to the power plugs with one of the following
options:
AC 24V: Connect 24V cables to terminals AC 24V.
PoE+: Connect the RJ45 jack to a PoE compatible network device
that supplies power through the Ethernet cable.
5. Adjusting the camera position
A. Use the T10 security Torx wrench to adjust the bracket Tilt angle (2) (Figure
6) and to adjust the bracket Pan angle (3) (Figure . 6)
6. Adjusting the sun shield hood
A. Move the sun shield hood (4) (Figure 6) forward and backward to adjust the
position of the sunshade.
Note: When the camera is mounted inverted to a pendant 1 ½ ‘’ NTP pipe you
must remove the sun shield hood by unscrewing the M3x0.5P (L = 8mm)
screw with the T10 security Torx wrench (3) (Figure 11) and relocate the
sun shield with screw as per the sun shield hood located in Figure 11.
CAUTION: Extending the sun shield hood forward could obstruct the field of view
(FOV) when the camera lens is set to ‘Wide’.
7. Location of camera buttons, connections and Desiccant bag
Note: The figure below indicates the location of the camera buttons and
connections (1) (Figure 12) and Desiccant bag (2) (Figure 12) on the camera.
Figure 12
Table 2: Universal Mounting plate symbols and descriptions
Plate
Symbol
Name
Description
4
4S Junction
Box
Attach the plate to a North American 4 inch
square electrical box.
O
Octagon Box
Attach the plate to a North American octagon
electrical box.
U
Electrical box
(UK)
Attach the plate to a UK electrical box.
E
Electrical box
(EU)
Attach the plate to a European electrical box.
Warnings
1. For US and Canada use a NRTL listed power adaptor.
2. The mains power adaptor equipment should be marked LPS (Limited
Current Source) or PS2 and rated according to 50C, 24VAC, 1.27A min
or PoE IEEE802.3at type 2 Class 4, 48VDC, 0.38A min.
3. To meet security immunity requirements use an uninterruptable PSU to
supply power to the mains adaptor or POE mid/end span.
4. The cables for 24Vac, Audio and Alarms should not exceed 3m unless
additional measures are taken to reduce the effect of interference picked
up on the cables.
5. USB and Analogue Video out cables should only be used temporarily for
service and not permanently installed.
6. For outdoor use the camera should be mounted at least 3m above ground
level”
© 2019 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or registered
trademarks. Unauthorized use is strictly prohibited.
Specyfikacje produktu
Marka: | Illustra |
Kategoria: | Bewakingscamera |
Model: | IPS02-B15-OI03 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Illustra IPS02-B15-OI03, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Bewakingscamera Illustra
22 Września 2024
22 Września 2024
22 Września 2024
Instrukcje Bewakingscamera
- Bewakingscamera Sony
- Bewakingscamera Samsung
- Bewakingscamera Tenda
- Bewakingscamera Motorola
- Bewakingscamera Stabo
- Bewakingscamera Logitech
- Bewakingscamera Xiaomi
- Bewakingscamera TP-Link
- Bewakingscamera Philips
- Bewakingscamera Bosch
- Bewakingscamera Hikvision
- Bewakingscamera EZVIZ
- Bewakingscamera Panasonic
- Bewakingscamera Canon
- Bewakingscamera Nedis
- Bewakingscamera AG Neovo
- Bewakingscamera Reolink
- Bewakingscamera Boss
- Bewakingscamera TRENDnet
- Bewakingscamera Marquant
- Bewakingscamera Toshiba
- Bewakingscamera D-Link
- Bewakingscamera August
- Bewakingscamera Ring
- Bewakingscamera Garmin
- Bewakingscamera Imou
- Bewakingscamera APC
- Bewakingscamera Honeywell
- Bewakingscamera Manhattan
- Bewakingscamera Strong
- Bewakingscamera Swann
- Bewakingscamera Cisco
- Bewakingscamera Broan
- Bewakingscamera ZTE
- Bewakingscamera Lindy
- Bewakingscamera Zebra
- Bewakingscamera JVC
- Bewakingscamera ZyXEL
- Bewakingscamera Furrion
- Bewakingscamera Linksys
- Bewakingscamera Google
- Bewakingscamera Digitus
- Bewakingscamera Dahua Technology
- Bewakingscamera Schneider
- Bewakingscamera Eufy
- Bewakingscamera Emos
- Bewakingscamera Marshall
- Bewakingscamera Somfy
- Bewakingscamera Uniden
- Bewakingscamera Thomson
- Bewakingscamera DiO
- Bewakingscamera Velleman
- Bewakingscamera Ferguson
- Bewakingscamera DataVideo
- Bewakingscamera Pyle
- Bewakingscamera Intellinet
- Bewakingscamera Vivotek
- Bewakingscamera Vtech
- Bewakingscamera Speco Technologies
- Bewakingscamera EtiamPro
- Bewakingscamera Edimax
- Bewakingscamera First Alert
- Bewakingscamera AirLive
- Bewakingscamera Maginon
- Bewakingscamera Planet
- Bewakingscamera Genie
- Bewakingscamera LevelOne
- Bewakingscamera Axis
- Bewakingscamera Sanyo
- Bewakingscamera Lorex
- Bewakingscamera Abus
- Bewakingscamera Elro
- Bewakingscamera Olympia
- Bewakingscamera Hama
- Bewakingscamera Marmitek
- Bewakingscamera Ubiquiti Networks
- Bewakingscamera Western Digital
- Bewakingscamera Netatmo
- Bewakingscamera ZKTeco
- Bewakingscamera Extech
- Bewakingscamera Denver
- Bewakingscamera Marshall Electronics
- Bewakingscamera Yale
- Bewakingscamera SereneLife
- Bewakingscamera Ernitec
- Bewakingscamera AVerMedia
- Bewakingscamera Genius
- Bewakingscamera Trevi
- Bewakingscamera Technaxx
- Bewakingscamera Overmax
- Bewakingscamera Grandstream
- Bewakingscamera Raymarine
- Bewakingscamera Powerfix
- Bewakingscamera Alecto
- Bewakingscamera Avidsen
- Bewakingscamera JUNG
- Bewakingscamera Burg Wächter
- Bewakingscamera Foscam
- Bewakingscamera Monacor
- Bewakingscamera Dörr
- Bewakingscamera M-e
- Bewakingscamera Smartwares
- Bewakingscamera Adj
- Bewakingscamera Elmo
- Bewakingscamera Profile
- Bewakingscamera Acti
- Bewakingscamera ACME
- Bewakingscamera Flamingo
- Bewakingscamera Caliber
- Bewakingscamera Eminent
- Bewakingscamera KlikaanKlikuit
- Bewakingscamera Trebs
- Bewakingscamera Ednet
- Bewakingscamera Steren
- Bewakingscamera Flir
- Bewakingscamera Arlo
- Bewakingscamera Nest
- Bewakingscamera Switel
- Bewakingscamera Chacon
- Bewakingscamera Hombli
- Bewakingscamera Konig
- Bewakingscamera BRK
- Bewakingscamera Gira
- Bewakingscamera Interlogix
- Bewakingscamera IC Intracom
- Bewakingscamera EverFocus
- Bewakingscamera Satel
- Bewakingscamera POSline
- Bewakingscamera Notifier
- Bewakingscamera Hawking Technologies
- Bewakingscamera Friedland
- Bewakingscamera Nexxt
- Bewakingscamera Beafon
- Bewakingscamera INSTAR
- Bewakingscamera Ganz
- Bewakingscamera Summer Infant
- Bewakingscamera Verint
- Bewakingscamera Brinno
- Bewakingscamera Rostra
- Bewakingscamera Caddx
- Bewakingscamera Spyclops
- Bewakingscamera EKO
- Bewakingscamera Kguard
- Bewakingscamera Indexa
- Bewakingscamera ClearView
- Bewakingscamera VideoComm
- Bewakingscamera IMILAB
- Bewakingscamera 3xLOGIC
- Bewakingscamera Pelco
- Bewakingscamera Inkovideo
- Bewakingscamera Pentatech
- Bewakingscamera SecurityMan
- Bewakingscamera Aigis
- Bewakingscamera Exacq
- Bewakingscamera Brickcom
- Bewakingscamera Laxihub
- Bewakingscamera Securetech
- Bewakingscamera E-bench
Najnowsze instrukcje dla Bewakingscamera
23 Września 2024
23 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024