Instrukcja obsługi IFM ZZ0432


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla IFM ZZ0432 (7 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
Short instructions
Cooling water control panel
ZZ0432
80000588 / 00 10 / 2021
UK
UK
UK
UK
UK
2
1 System overview
1
3 4 5
350
360
33
426,8
129,1
M22x1,5R
½
2
67
8
1 Flow sensor Monitors and indicates the cooling water flow rate.
The setting of two switch points enables detection of:
- excess flow (leakage / burst pipes / lost tips),
- low flow (clogged /damaged pipes).
3
UK
2 Water stop valve Closes the water supply to the system in case of failure and
prevents water spillage.
3 Backstop Prevents cooling water loss through the return pipe in case of
failure (broken tip / burst pipe).
4 Regulating valve Continuous regulation of the flow rate.
5 Pressure sensor Monitors the operating pressures, very fast response times are
attained if pressure falls (broken tips).
6 Expansion
cylinder
When a welding tip is replaced or if there is a fault (2/2-way
valve in the inlet pipe is closed), the expansion cylinder actively
sucks back the cooling water and switches off the pressure.
7 5/2-way valve The 5/2-way valve controls the expansion cylinder.
8 tube connection Ø 8 mm
► →Observe the instructions of the sensors www.ifm.com.
2 Functions and features
Pressure Equipment Directive (PED)
The units comply with the Pressure Equipment Directive and are designed
and manufactured for group 2 fluids in accordance with the sound engineering
practice.
Use of group 1 fluids on request.
3 Setting of the flow sensor
The flow sensor monitors the flow rate in the supply pipe by means of a window
function. This is achieved by setting the output function of the two outputs:
OU1 and OU2 = Fno, window / normally open. With this setting an acceptable
range is monitored.
The flow rate depends on the water supply and the set-up of the welding tongs.
The setting of the switch-on points (SP1, SP2) and the switch-off points (rP1, rP2)
depends on the installation.
Optimum monitoring of the start up characteristics as well as processrelated flow
fluctuations during operation is possible via additional monitoring times in the
robot software.


Specyfikacje produktu

Marka: IFM
Kategoria: Niesklasyfikowane
Model: ZZ0432

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z IFM ZZ0432, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane IFM

IFM

IFM PN7043 Instrukcja

28 Stycznia 2025
IFM

IFM MGS213 Instrukcja

28 Stycznia 2025
IFM

IFM MGS214 Instrukcja

28 Stycznia 2025
IFM

IFM MFS224 Instrukcja

28 Stycznia 2025
IFM

IFM MFS225 Instrukcja

28 Stycznia 2025
IFM

IFM MFS228 Instrukcja

28 Stycznia 2025
IFM

IFM PN2043 Instrukcja

28 Stycznia 2025
IFM

IFM ID5058 Instrukcja

28 Stycznia 2025
IFM

IFM EVT728 Instrukcja

28 Stycznia 2025
IFM

IFM EVF729 Instrukcja

28 Stycznia 2025

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025