Instrukcja obsługi IFM SR0153


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla IFM SR0153 (9 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/9
Operating instructions
Evaluation system for flow sensors
VS3000
SN0151
SN0152
SR0153
704948 / 01 04 / 2021
UK
2
1 Preliminary note
The operating instructions apply to all control monitors of type VS3000 for 35 mm
DIN rail mounting. The only difference between the individual units is the type of
supply voltage which is indicated on the type label of the unit. 2 versions are avail-
able: 24 V DC and 85 to 265 V AC.
The operating instructions are part of the unit. They contain information about the
correct handling of the product. Read them before use to get familiar with operat-
ing conditions, mounting and operation. Adhere to the safety instructions. The
operating instructions are made for authorised persons according to the EMC and
low voltage guidelines.
Contents
1 Preliminary note 2
...................................................................................................
2 Safety instructions 3
...............................................................................................
3 Function and features 4
..........................................................................................
4 Mounting ..............................................................................................................
4
4.1 Mounting of the sensors 5
................................................................................
5 Electrical connection 5
............................................................................................
5.1 Terminal connection 6
.......................................................................................
5.2 Power supply (Power) 6
..................................................................................
5.3 Connection of sensors 7
...................................................................................
5.4 Relay outputs 7
................................................................................................
6 Settings ...............................................................................................................
7
7 Operation ............................................................................................................
8
7.1 Function diagram flow monitoring 8
.................................................................
8 Maintenance, repair, disposal 9
.............................................................................
9 Technical data and scale drawing 9
........................................................................
3
UK
2 Safety instructions
Adhere to the operating instructions. Non-observance of the instructions,
operation which is not in accordance with use as prescribed below, wrong in-
stallation or incorrect handling can affect the safety of operators and machinery.
The unit must only be installed, connected and put into operation by a qualified
electrician as during the installation dangerous voltages may be exposed. The
safe function of the unit and the plant is only guaranteed when installation is
correctly carried out.
Disconnect the unit externally before handling it. Also disconnect any indepen-
dently supplied relay load circuits.
Be careful when handling the unit once power is applied. This is only allowed
by qualified personnel due to the protection rating IP 20.
The design of the unit corresponds to protection class II (EN 61010) except for
the terminal blocks. Protection against accidental contact (safety from finger
contact to IP20) for qualified personnel is only ensured if the terminals have
been completely inserted. For this reason the unit must always be installed in a
control cabinet which can only be opened with a tool, for pollution degree 2 and
overvoltage category II.
For DC units the external 24 V DC supply must be generated and supplied ac-
cording to the requirements for safe extra-low voltage (SELV) since this voltage
is provided near the operating elements and at the terminals for the supply of
sensors without further protection measures.
In case of malfunction of the unit or queries please contact the manufacturer.
Any tampering with the device can seriously affect the safety of operators and
machinery. This is not permitted and leads to an exclusion of liability and war-
ranty.


Specyfikacje produktu

Marka: IFM
Kategoria: Niesklasyfikowane
Model: SR0153

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z IFM SR0153, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane IFM

IFM

IFM PN7043 Instrukcja

28 Stycznia 2025
IFM

IFM MGS213 Instrukcja

28 Stycznia 2025
IFM

IFM MGS214 Instrukcja

28 Stycznia 2025
IFM

IFM MFS224 Instrukcja

28 Stycznia 2025
IFM

IFM MFS225 Instrukcja

28 Stycznia 2025
IFM

IFM MFS228 Instrukcja

28 Stycznia 2025
IFM

IFM PN2043 Instrukcja

28 Stycznia 2025
IFM

IFM ID5058 Instrukcja

28 Stycznia 2025
IFM

IFM EVT728 Instrukcja

28 Stycznia 2025
IFM

IFM EVF729 Instrukcja

28 Stycznia 2025

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025