Instrukcja obsługi IFM E70600


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla IFM E70600 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/3
Installation instructions
Quad M12
E70588
Quad
E70600
7390873/00 03/2014
UK
2
1 Functions and features
The Quad module is used to open an AS-i spur or for additional voltage supply
(current rating 8 A).
With the Quad M12 module the AS-i voltage and external voltage can be
tapped via the M12 socket (current rating 4 A).
Pin connection of the M12 socket:
3
1 2
4
5
pin 1 AS-i +
pin 2 0 V
pin 3 AS-i -
pin 4 + 24 V
pin 5 functional earth
2 Installation
Disconnect power.
2.1 Installation of the lower part
Choose a plane mounting
surface. The entire bottom of
the module must lie flat on the
mounting surface.
Screw the lower part onto the
mounting surface. To do so,
use the mounting holes (1)
and M4 mounting screws with
washers M4 (not supplied with
the device). Tightening torque
2.3...2.5 Nm.
LINE 1
LINE 2
Place the profile seals (3) into the slots (2) of the module lower part. If
the module is at the end of the cable run, the blanking seals (4) must
be used to ensure the IP 65 protection rating.
3
UK
2.2 Insert the at cable / version Quad
Insert the incoming AS-i flat cable (yellow or black for the external voltage
supply) into the cable duct "Line 1".
Insert the outgoing AS-i flat cable (yellow or black) into the cable duct "Line 2".
Place the cables correctly in the profile slot.
The two cable ducts are electrically connected in parallel.
For the Quad version always use two AS-i flat cables of the same
colour (yellow/yellow or black/black) in "Line 1" and "Line 2".
2.3 Insert the at cable / version Quad M12
Insert the AS-i flat cable (yellow) into the cable duct "Line 1".
Insert the 24 V flat cable (black) into the cable duct "Line 2".
Place the cables correctly in the profile slot.
2.4 Installation of the upper part
Position the upper part
and tighten the screws (5)
crosswise (tightening torque
2.5 Nm).
Ground the devices via the
earth springs (6) if necessary.
For connection of a plug to Quad M12:
Tightening torque of the M12 socket: 0.8 Nm. Also observe the tightening
torque of the connection cable used.


Specyfikacje produktu

Marka: IFM
Kategoria: Niesklasyfikowane
Model: E70600

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z IFM E70600, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane IFM

IFM

IFM PN7043 Instrukcja

28 Stycznia 2025
IFM

IFM MGS213 Instrukcja

28 Stycznia 2025
IFM

IFM MGS214 Instrukcja

28 Stycznia 2025
IFM

IFM MFS224 Instrukcja

28 Stycznia 2025
IFM

IFM MFS225 Instrukcja

28 Stycznia 2025
IFM

IFM MFS228 Instrukcja

28 Stycznia 2025
IFM

IFM PN2043 Instrukcja

28 Stycznia 2025
IFM

IFM ID5058 Instrukcja

28 Stycznia 2025
IFM

IFM EVT728 Instrukcja

28 Stycznia 2025
IFM

IFM EVF729 Instrukcja

28 Stycznia 2025

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025