Instrukcja obsługi Hubbell J1639R

Hubbell Heater J1639R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hubbell J1639R (40 stron) w kategorii Heater. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/40
1
OPERATING AND MAINTENANCE
MANUAL FOR
ELECTRIC BOOSTER HEATER
ELECTRIC HEATER COMPANY
BASE MODEL J
UM ANSI/NSF5
201 Edition7
2
HUBBELL
ELECTRIC HEATER COMPANY
45 SEYMOUR STREET
P.O. BOX 288
STRATFORD, CT 06615
PHONE: (203) 378-2659
FAX: (203) 378-3593
INTERNET: http://www.hubbellheaters.com
-- IMPORTANT --
Always reference the full model number and serial number when calling the factory.
WARNING / CAUTION
1. Tank is to be completely filled with water and all air is to be vented before energizing.
2. Due to the rigors of transportation, all connections should be checked for tightness before
heater is placed in operation.
3. Safety relief valve must be installed in tapping provided.
4. The refractory material used in heating elements may absorb some moisture during
transit, periods of storage, or when subjected to a humid environment. This moisture
absorption results in a cold insulation resistance of less than ( ) megohms. If thisone 1
heater has been subjected to the above condition, each heating element must be checked
for insulation resistance before energizing. Contact the factory for a replacement element.
5. KEEP AWAY FROM LIVE ELECTRICAL CIRCUITS.
Do not perform any maintenance, make any adjustments, or replace any components
inside the control panel with the high voltage power supply turned on. Under certain
circumstances, dangerous potentials may exist even when the power supply is off. To
avoid casualties, always turn the power supply safety switch to off, turn the charge or
ground the circuit before performing any maintenance or adjustment procedure.
6. The unit is designed to operate at pressure not more than 150 psi.
7. Generalized instructions and procedures cannot anticipate all situations. For this reason,
only qualified installers should perform the installations. A qualified installer is a person
who has licensed training and a working knowledge of the applicable codes, tools,
equipment, and methods necessary for safe installation of an electric resistance water
heater. If questions regarding installation arise, check your local plumbing and electrical
inspectors for proper procedures and codes. If you cannot obtain the required
information, contact the company.
8. Water Quality Requirements – Recommended water hardness is 4 to 6 grains of
hardness per gallon (GPG). Water hardness above 6 GPG should be treated by a water
conditioner (water softener or in-line treatment). Water hardness below 4 GPG also
requires treatment to reduce potential corrosion. Excessive GPG will result in higher
operating and maintenance costs and will reduce product longevity. Chlorides must
not exceed 50 parts per million (ppm). Excessive chlorides will result in metallic
corrosion and will reduce product longevity. Water treatment has been shown to
reduce costs associated with de-liming the booster as well as reducing metallic
corrosion. Product failure caused by these conditions is not covered under warranty.
See warranty for complete details.
9. This water heater is not intended for space heating applications.
10. The water heater is factory set at 185°F for booster water heating applications. This
results in the possibility of a scalding water injury. A full thickness skin burn can
occur in less than one second of exposure to water at this temperature.
3
TABLE OF CONTENTS
SECTION TITLE PAGE No.
I GENERAL DESCRIPTION AND CONSTRUCTION 4
II INSTALLATION AND START-UP 9
III SCHEDULED MAINTENANCE AND OPERATION 24
IV TROUBLESHOOTING 26
V SERVICING AND REPLACEMENT OF PARTS 32
VI SERVICE PARTS LIST 35
VII TORQUE VALUES 37
VIII WARRANTY INFORMATION 38

Specyfikacje produktu

Marka: Hubbell
Kategoria: Heater
Model: J1639R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hubbell J1639R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Heater Hubbell

Hubbell

Hubbell J1639R Instrukcja

21 Września 2024
Hubbell

Hubbell J1613S Instrukcja

19 Września 2024
Hubbell

Hubbell J615R Instrukcja

19 Września 2024
Hubbell

Hubbell J636R Instrukcja

19 Września 2024
Hubbell

Hubbell J1639T Instrukcja

19 Września 2024
Hubbell

Hubbell J67T4 Instrukcja

18 Września 2024
Hubbell

Hubbell J615RS Instrukcja

18 Września 2024

Instrukcje Heater

Najnowsze instrukcje dla Heater

GoldAir

GoldAir GFH260 Instrukcja

21 Września 2024
SunRed

SunRed WMGT13S Instrukcja

21 Września 2024
JANDY

JANDY CXI650NN Instrukcja

21 Września 2024
Dri Eaz

Dri Eaz Velo Pro Instrukcja

21 Września 2024
Heller

Heller HOIL9 Instrukcja

21 Września 2024
Hatco

Hatco 3CS-6B Instrukcja

21 Września 2024
Heller

Heller HOFC2000 Instrukcja

20 Września 2024