Instrukcja obsługi HQ HA30W

HQ odbiornik HA30W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla HQ HA30W (60 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/60
PUBLIC ADDRESS
AMPLIFIER
Installation and User Instructions
For models:
• HQ-HA30W
WARNING:THIS APPLIANCE MUST BE EARTHED
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
The wires in the mains lead are coloured
in accordance with the following code:
GENERAL INSTALLATION
DO NOT run microphone cables near mains, data, telephone or 100V line cables.
DO NOT run 100V line cables near data, telephone or other low voltage cables.
DO NOT exceed 90% of the amplifiers output power when using 100V line (speech only).
DO NOT exceed 70% of the amplifiers output power when using 100V line (high level
background music).
DO NOT use re-entrant horn loudspeakers for background music unless the loudspeaker has
been specifically designed for this purpose.
AVOID jointing the microphone cable, when this is unavoidable make sure a good screened
connector is used, e.g. XLR.
ALWAYS use a balanced or floating low impedance microphone terminating into a balanced
input on long microphone cable runs.
ALWAYS use a mains grade double insulated cable for the loudspeaker cable runs.
ENSURE that all loudspeakers are in-phase.
ENSURE that there are no short circuits on the loudspeaker line before connecting to the
amplifier.
Green and Yellow: Earth (E)
Blue: Neutral (N)
Brown : Live (L)
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
• The green and yellow coloured wire must be
connected to the terminal that is marked by the letter E,
marked by the safety earth symbol or coloured green
and yellow.
• The blue coloured wire must be connected to the
terminal that is marked with the letter N or coloured
black.
• The brown coloured wire must be connected to the
terminal that is marked with the letter L or coloured red.
If a 13 Amp (B.S.1363) plug or any other type of plug is
used,a 5 Amp fuse must be fitted either in the plug or at the
distribution board.
FRONT PANEL Mixer Amplifier
2 3 4 5 6 7 8 9 10
11 12
1
1. Mic 1 Input (Phone) 7. Master Tone Control (Bass)
2. Mic 1 Volume Control 8. Master Tone Control (Treble)
3. Mic 2 Volume Control 9. Master Volume Control
4. Mic 3 Volume Control 10.Power On/Off Switch
5. Aux 1 Volume Control 11.Output Level Indicator LED
6. Aux 2 Volume Control 12.Power On/Off Indicator LED
REAR PANEL
34 6 9 11
13 1412
2
16 17 18 19 20 21
5 7 8 10
1
15
1. Earth Connection Screw 12. AC Fuse Holder
2. DC Power Supply Terminals 13. Mains Voltage (115V/230V) Selector Switch
3. Loudspeaker Output Terminals 14. Mains Input Socket
4. Mic3 (Line / Mic) Selector Switch 15. Power Input (RCA Phono)
5. Mic3 Input (XLR / Balanced) 16. Pre Output (RCA Phono)
6. Mic3 Input (Phone / Balanced) 17. Tape Output(2X RCA Phono)
7. Mic2 Input (XLR / Balanced) 18. Aux2 Input (2X RCA Phono)
8. Mic2 Input (phone / Balanced) 19. Aux1 Input (2X RCA Phono)
9. Mic1 Input (XLR / Balanced) 20. TEL / EMER Input Terminals
10. Mic1 Input (DIN / Balanced) 21. TEL / EMER Input Level Control
11. Chime On/Off switch
12345678
A
B
C
D
87654321
D
C
B
A
Title
Number RevisionSize
A3
Dat e: 7-May-2 002 Sheet of
File: A:\PBL3000.SC H Drawn By:
3
2
1
3
2
1
3
2
1
25
31
4
MUTE
CHIME
VOX
VOX
POWER AMP
OUTPUT BOARD
100V
70V
25V
8ohm
COM
115V
230V
DC24V
+
_
G
+B
16V
PHANTOM POWER
+V
ON
OFF
MIC1 PRE
MIC2 PRE
MIC3 PRE
AUX1 PRE
AUX2 PRE
OFF
ON
T-OUT(350mv)
TONE MASTER INC(1V)
TEL PRE
GND
Mains Connection
The supply transformer has been designed for use either 115V AC or 230V AC,
selected by slide switch on rear panel. The amplifier is factory set at 230V AC mains
voltage.
Battery Connection (24V DC)
When using external batteries, earth the amplifier via the screw terminal because there are high
voltages present. Electrical stability of the system is increased by earthing the case.
NOTE: The connection cable must be fitted with an in-line fuse, quick blow type (30W : 5A,
60W : 8A, 120W : 15A). When connecting batteries please ensure correct polarity.
Microphone Connections
Mic1 input is either a balanced standard 6.35mm stereo jack on front panel or XLR and DIN
on the rear panel (With selectable phantom power). Wiring is as follows:
XLR (Balanced Operation)
Pin1 : Screen
Pin2 : Signal (live)
Pin3 : Signal (return)
DIN (Balanced operation)
Pin1 : Signal (live)
Pin2 : GND
Pin3 : Signal (return)
Pin4 : Priority Control
Pin5 : GND
6.35mm Stereo Jack Plug (Balanced operation)
Tip : Signal (live)
Ring : Signal (return)
Sleeve : Screen
Mic1 input has VOX priority which will override Mic2-3 and Aux1-2 input signals but
NOT the TEL/EMER input.
Mic1-3 input are XLR,DIN and phone jack with selectable phantom power located on the
rear panel and wired as above. The phantom power is factory set and be enabled as
follows:
1. Remove the power lead from the AC wall socket.
2. Remove the top cover.
3. Locate the link pins (Marked SW102) on the Printed Circuit Board behind the microphone
XLR input socket.
4. Connect the black shorting plug to the centre pin and ON position to enable the phantom
power.
2 1
3
1
4
2
5
3
Chime
Switch on the chime on/off switch on the rear panel and short the pin4, pin5 of DIN
socket or short the sleeve and ring of phone plug Mic 1. This will activate the chime function
(“Ding-Dong” attention signal preceding a call).The default volume of the chime is pre-set at the
factory and is adequate for most applications.
Telephone Connection
This input is for emergency announcements/signals and is not effected by the master volume
control. Input level can be set by level control on the rear. The TEL input has the highest priority
and will override all other inputs.
Aux Connection
This amplifier provides two auxiliary inputs that may be used for connecting other signal sources
such as a radio tuner, CD player or cassette player. The level control operates individually. Turn
the control clockwise to increase the volume or anticlockwise to reduce the volume.
The Aux input sockets are standard RCA phono, two sockets are supplied and these are linked
together internally. This allows stereo signal sources to be used without the need to obtain a
special lead, however you may wish to check with the manufacturer of the signal source to ensure
that no damage will result if the left and right output channels are put in parallel.
RCA Phono plug connections
Tape Output Connection
These standard RCA phono sockets provide a mixed output suitable for connection to a tape or
cassette recorder.
Power In and pre Out
Connects the mixer/ preamplifier stage to the power amplifier stage. The connecting link must be
plugged in for normal operation as a mixer/amplifier. If a compressor/limiter, equalizer or other
external signal processor is used in the sound system, connect the “PRE OUT” to the input of the
external processor and the output of the processor to “POWER IN” In the signal chain. “PRE OUT”
is after the tone controls and the master volume control.
Loudspeaker Connection
This equipment provides four different types of loudspeaker output, these are 100V, 70V and 25V
line and low impedance, you can only use one of these outputs at a time. Any attempt to use two
or more of these may result in damage to the amplifier.
Sleeve: Screen
Pin: Signal
Technical Specifications
Type Mixer Amplifier
Model HQ-HA30W
Mains Voltage AC 115V / 230V , 50 / 60Hz ± 10% switchable Supply
Battery Voltage DC 24V (MAX 10% deviation)
Max : Output power
Rated :
45W
30W
Outputs Speaker outputs: 8Ω,25V,70V,100V
TAPE out : 350mV, 4.7KΩ
Pre out: 1V, 600Ω
Inputs Mic1~3 : 1mV,250Ω balanced with phantom power selectable.
Aux1:200mV,47KΩ,unbalanced.
Aux2:500mV,47KΩ,unbalanced.
Line(Mic3):200mV,47KΩ,balanced.
TEL : 0.1~1V,600Ω,Adjustable,balanced.
Power in:1V,47KΩ,unbalanced
Frequency response Mic1~Mic3 : 60Hz ~ 15KHz ± 3dB
Aux1~Aux2 : 60Hz ~ 15KHz ± 3dB
TEL : 100Hz ~ 15KHz ± 3dB
Total harmonic distortion Less than1% at 1KHz,rated power
Signal to noise ratio All Volume Controls C.C.W. : 75dB below rated power
Mic1 ~ 3 : 60dB below rated power
Aux1 ~ 2 : 70dB below rated power
TEL : 70dB below rated power
Tone Controls Bass : ±10 dB at 100Hz
Treble: ±10 dB at 10KHz
Controls Mic1~Mic3 volume control
Aux1~Aux2 volume control
Master volume control
Tone controls (Bass,Treble)
TEL input level control
Mic3 (Line-Mic) selector switch
Chime on/off switch
AC 115V / 230V voltage selector switch
Indicators Power indicator (LED),output level indicators (3 LEDS)
AC power consumption 100 watts
DC power consumption 2 A
Chime Two tone chime (Ding-dong attention signal preceding a call).
Priority (VOX) Priority level (Using for Mic1, the 5 pole DIN connector, phone jack or
XLR connector)
Tel / Emer Mic1 Mic2 Mic3 Aux/CD
3 2 1 1 1
Dimentions ( H × ×W D ) 88 × ×430 260 mm
Weight Approx 6.5kg
Color Black
Mounting options Table top or 19” rack mountable
PUBLIC ADDRESS
VERSTERKER
INSTALLATIE- EN GEBRUIKSAANWIJZING
VOOR MODELLEN:
• HQ-HA30W

Specyfikacje produktu

Marka: HQ
Kategoria: odbiornik
Model: HA30W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z HQ HA30W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik HQ

HQ

HQ HA30W Instrukcja

30 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Harper

Harper HDT2-5010 Instrukcja

2 Kwietnia 2025
Harper

Harper HDT2-2010 Instrukcja

2 Kwietnia 2025
QSC

QSC SPA-Qf 60x2 Instrukcja

1 Kwietnia 2025
Streacom

Streacom TL1 Instrukcja

30 Marca 2025
Graupner

Graupner GR-8 Instrukcja

30 Marca 2025
MB Quart

MB Quart FA2-2000.1 Instrukcja

29 Marca 2025
MB Quart

MB Quart FA2-1500.1 Instrukcja

29 Marca 2025
MB Quart

MB Quart FA2-1000.1 Instrukcja

29 Marca 2025
MB Quart

MB Quart FA2-400.4 Instrukcja

29 Marca 2025
MB Quart

MB Quart FA2-900.5 Instrukcja

29 Marca 2025