Instrukcja obsługi Hozelock PondVac 1752

Hozelock odkurzacz PondVac 1752

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hozelock PondVac 1752 (32 stron) w kategorii odkurzacz. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/32

1752

PondVac

Hozelock Ltd.

Midpoint Park,

Birmingham B76 1AB. England

Tel: +44 (0) 121 313 1122

info@hozelock.com

www.hozelock.com

33791-002

Caution! Please keep these

operating instructions in a safe

place. Ensure that all

operation and maintenance is carried

out in line with these instructions.

A Nuts (x2)

B Vacuum Unit

C Tubes (x4)

D Support Handle

E Main Handle

F Hose Adaptor & Waste Hose

G Cable Clips (x4)

H Wide Nozzle

I Narrow Nozzle

J Open Nozzle

Intended use

The Pond Vacuum Pump is speciﬁcally

designed to remove waste material from

a pond. The minimum pond operating

depth for the pond vacuum is 0.2m.

Safety Information

The Pond Vacuum is intended only for

pond cleaning purposes. Using the

product for any other application may

result in injury or product damage.

This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory

or mental capabilities or lack of

experience and knowledge if they

have been given supervision or

instruction concerning use of the

appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

This appliance must not be used if any

people are in the water.

( ) This applianceAustralia & NZ only

is not intended for use by young

children or inﬁrm persons unless

they have been adequately

supervised by a responsible person

to ensure that they can use the

appliance safely.

Young children should be supervised

to ensure that they do not play with

the appliance.

The Pond Vacuum is ﬁtted with a

thermal fuse, which will switch off the

Pond Vacuum if it overheats. If this

occurs, switch off the power at the

mains supply. Inspect the Pond

Vacuum for possible cause and allow

it to cool down for approximately 15

minutes. You may then continue to

use the Pond Vacuum as normal.

Note: The fuse will only reset once

the temperature has dropped to a

safe level, which in certain

circumstances could take some time.

The combination of water and

electricity can lead to possible loss of

life if the Pond Vacuum is incorrectly

connected or misused. You must not

be in the pond when operating the

Pond Vacuum. A 10mA or 30mA

Residual Current Device (RCD) must be

ﬁtted to the mains supply.

Always unplug or disconnect all

appliances in the pond from the

electricity supply before putting your

hands in the water. Only use the Pond

Vacuum when plugged into a

correctly ﬁtted earthed socket. Keep

the power plug and all connections

points dry! Do not operate or leave

the Pond Vacuum in the rain. Never

carry or pull the Pond Vacuum by the

connection cable. Never operate the

Pond Vacuum if the cable or housing

are damaged! The supply cable

cannot be replaced so if the cable

becomes damaged the Pond Vacuum

should be discarded. Electrical

installations at garden ponds must

meet the international and national

regulations valid for installers. Never

open the Pond Vacuum housing or its

associated components unless this is

requested for in the operating

instructions. The maximum head of

the Pond Vacuum is 1.5m.

Assembly of the Pond

Vacuum

1. Insert the narrow end of one of the

connecting tubes (C) into the opening

at the rear of the Pond Vacuum head

(B) and screw the nut (A) until hand

tight.

2. Insert the narrow end of one of the

connecting tubes (C) through the

opening at the rear of the support

handle (D). Position the handle as

required and screw the nut (A) until

hand tight. It is recommended that

the support handle is always located

on the tube furthest from the vacuum

head.

3. Four tube sections are provided so

that the length of the Pond Vacuum

can be altered depending on the

depth of pond to be cleaned. Tubes

are connected together by inserting

the narrow end of one tube into the

wide end with plastic seal of another

(C). Simply press the parts together

until tight. Add or remove the tubes

as necessary. Twist and pull the tubes

to disassemble. Caution! Never use

excessive force to assemble or

disassemble the tubes as this may

result in the tubes or seals being

damaged!

4. The main handle (E) is attached to a

tube by simply pushing the narrow

end of the handle into the wide end

of a tube (C) until tight. Twist and

pull the handle to disassemble.

5. The hose adaptor (F) is attached to

the main handle (E) via a bayonet

ﬁtting. Align the corresponding lugs

on the handle and adaptor, push on

and turn anti-clockwise until locked

into place (see 5A). If when using the

Pond Vacuum there is a leak in this

area, re-position and tighten the

winged hose clip as required (see 5).

6. The Pond Vacuum is provided with

four cable tidy clips (G), which should

always be ﬁtted to keep the power

cable secure along the tubes and

prevent any safety issues. Firstly push

the cable into the clip and then press

this onto the plastic clip holder on the

end of the tube (C). Use a clip for each

section of aluminium tube used.

7. Nozzles are attached to the Pond

Vacuum by pushing them on to the

front of the vacuum head (See 7).

Caution! Only use enough force so

that the nozzle is held in position!

When nozzles are not in use they can

be stowed neatly away on the support

handle (See 7A).

Operation of Pond Vacuum

Caution! Take extra care when using

the Pond Vacuum near any aquatic life!

Three alternative nozzles have been

provided to give as much versatility to

the Pond Vacuum as possible. The

wide nozzle (H - Fig 7) is best for

cleaning the base and sides of the

pond whilst the narrow nozzle (I - Fig

7) is good for accessing corners and

small areas of the pond. A further

open nozzle (J - Fig 7) is provided

speciﬁcally to extract larger debris

from the pond e.g. small stones up to

8mm. Using this “openWarning!

nozzle” may cause the Pond Vacuum to

block more frequently. Select a nozzle

and ﬁt as described in section 7 of the

assembly instructions.

With the Pond Vacuum fully

assembled, position it so that the Pond

Vacuum head (B) is under the water.

Position the end of the plastic waste

hose so that it goes to the desired

waste point e.g. in a ﬂowerbed or

drain. If the waste hose is notNote:

long enough it can be easily replaced

by purchasing a suitable length of

25mm diameter spiral reinforced hose

from any aquatics outlet. Now connect

the power. Caution! Do not operate

the pump unless the Pond Vacuum

head is submerged under the water, as

this will signiﬁcantly reduce its life!

Move the Pond Vacuum so that the

nozzle reaches the area to be cleaned

ensuring it is remains fully submerged.

After a few seconds dirty water should

be seen ﬂowing from the end of the

waste hose.

If using the wide nozzle (H or J Fig 7),

move the Pond Vacuum backwards and

forwards in a smooth motion over the

area to be cleaned trying not to disturb

too much of the sediment which will

cause the pond to become excessively

cloudy. Continue until all the required

waste has been removed. If using the

narrow nozzle (I - Fig 7) carefully move

the Pond Vacuum in to the area

needing to be cleaned until all the

necessary waste has been removed.

Caution! Do not force the narrow

nozzle into the base or sides of the

pond as this may cause damage to the

liner!

It is possible to clean shelves with the

Pond Vacuum but it must be pumping

ﬁrst. To do this fully submerge the

Pond Vacuum until water is being

pumped. The Pond Vacuum can then

be withdrawn from the pond up to the

tip of the nozzle (but not completely

clear of the water) allowing high

shelves to be cleaned.

Note: When withdrawing the pond

vacuum from the water it is normal to

see water pumping out through the

drain holes at the back of the vacuum

head.

Troubleshooting

Problem Cause Remedy

The Pond Vacuum is only pumping a very Excessive height difference between Reduce the number of tubes used in shallow

small amount of water the surface of the pond and the main areas of the pond or lower the handle closer

handle to the ground

The Pond Vacuum is partly blocked Try shaking the Pond Vacuum to remove the

blockage.

Follow the Unblocking section in these

instructions

No water is being pumped by the Pond The Pond Vacuum has trapped air Fully submerge the Pond Vacuum and shake to

Vacuum free any air that might be trapped. Alternatively,

turn the Pond Vacuum over until all the trapped

air is released

The waste pipe is kinked Check that the waste pipe has not been kinked

The Pond Vacuum is blocked Follow the Unblocking section in these

instructions

The power supply is not switched on Check power supply, RCD, fuses and wiring

The Thermal Protection has tripped See Safety Information section in these

instructions

The Pond Vacuum has not been fully Ensure that the whole of the Pond Vacuum head

submerged is submerged below the surface of the water

until water is being pumped

Cleaning/Unblocking

Caution! Do not use the Pond Vacuum

to remove long blanket weed, as this

will clog the nozzles!

In the event that the Pond Vacuum

should become blocked follow this

procedure to unblock:

1. Withdraw the Pond Vacuum from the

water and disconnect from the power

supply.

2. Check the end of the nozzle and

remove any debris that may be

blocking it (See 8).

If debris was found to be blocking the

nozzle, no further action is required

and the Pond Vacuum can be used

a gain. If not move on to step 3.

3 . Remove the hose adaptor by twisting

it one-quarter turn clockwise until

free and gently pull downwards (See

9).

4. Check inside the hose adaptor for

debris and remove it.

5. Also check inside the handle (See 9A)

for any blockages.

If debris was found to be causing a

blockage in the adaptor or handle, no

further action is required and the

Pond Vacuum can be used again. If

not move on to step 6.

6. Remove nozzle by twisting and

pulling off (See 10). Remove the Pond

Vacuums’ front cover by pressing

down the retaining clips and pulling

the cover off (See 10A).

7. Remove the impeller chamber by

pulling the assembly out (See 11)

8. Check that there is no debris/stones in

the front, side or back of the chamber

(see 12). Remove any debris if

necessary, rinsing the assembly in

pond water and rotating the impeller

to ensure it is free. Caution! The

impeller chamber contains sharp

blades and cannot be opened for

safety reasons.

9. Debris may also be trapped in the

main unit which can be removed by

shaking it vigorously.

10.Reassemble ensuring all components

are ﬁtted together correctly.

The Pond Vacuum should now be fully

functional again. If not, please refer

to the Trouble Shooting section of

these instructions.

Storage

Empty the Pond Vacuum of all water,

clean after every use and store in a

frost protected area.

Hozelock Cyprio 3 Year

Guarantee

If this Pond Vacuum becomes

unserviceable within 3 years of the

date of purchase it will be repaired or

replaced at our option free of charge,

unless in our opinion it has been

damaged or misused. Liability is not

accepted for damage due to accident,

improper installation or use.

Liability is limited to replacement of a

faulty product. This guarantee is not

transferable. It does not affect your

statutory rights. To obtain the beneﬁts

of the guarantee, ﬁrstly contact

HoZelock Cyprio Consumer Services

who may request that the Pond

Vacuum is sent along with proof of

purchase directly to the address below.

Hozelock Cyprio

Midpoint Park, Birmingham B76 1AB.

England.

Your appliance contains

valuable materials which

can be recovered or

recycled. Leave it at a local

civic waste collection point

Specyfikacje produktu

Marka:	Hozelock
Kategoria:	odkurzacz
Model:	PondVac 1752

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hozelock PondVac 1752, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odkurzacz Hozelock

Hozelock PondVac 1752 Instrukcja

24 Sierpnia 2024

Instrukcje odkurzacz

Najnowsze instrukcje dla odkurzacz

Tesla RoboStar SP300 Instrukcja

25 Grudnia 2024

Shark Rocket HV380 Instrukcja

25 Grudnia 2024

Russell Hobbs R-Vac RHRV100 Instrukcja

25 Grudnia 2024

VAX Atractivo VST144VL Instrukcja

25 Grudnia 2024

Tower VL30 Instrukcja

24 Grudnia 2024

Kärcher WD 3.5 P Premium Instrukcja

24 Grudnia 2024

MPM MOD-49 Instrukcja

23 Grudnia 2024

Miele S 381 Instrukcja

23 Grudnia 2024

Miele Classic C1 Hardfloor EcoLine Instrukcja

23 Grudnia 2024

LG Kompressor LcV800R Instrukcja

22 Grudnia 2024