Instrukcja obsługi Hotpoint NWXR473GVAA

Hotpoint Suszarka bębnowa NWXR473GVAA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint NWXR473GVAA (3 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
NWXR473GVAA—Hotpoint 6.0 Cu. Ft. Extra-Large Capacity Gas Dryer
Specication Revised 8/99
Dryer Dimensions (in inches)
36 42
27
23-1/2
2-1/2
25-1/2
Side View Rear View
8-1/2
28-1/4
23-1/2
11-1/2
Exhaust Options:
3-way via rear, left and bottom. Dryer is shipped exhausted to the rear.
Alternate exhausting knockouts are supplied.
Circuit Requirements:
An individual properly-grounded branch circuit, with a three-prong grounding-
type receptacle, protected by a 15- or 20-amp circuit breaker or a time-delay
fuse is required.
Gas Dryer Electric Rating:
120V, 60Hz, 15 Amp
Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas.
LP gas supply requires a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install a conversion kit. See
dryer ducting information for proper installation.
Installation Information: For complete information, see installation
instructions packed with product for current dimensional data.
R
Listed by
Underwriters
Laboratories
NWXR473GVAA—Hotpoint 6.0 Cu. Ft. Extra-Large Capacity Gas Dryer
Specication Revised 8/99
R
Listed by
Underwriters
Laboratories
Dryer Exhausting Information—Use Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Important Note:
GE Kit Number WE14X70 needed when converting rear exhaust to bottom or side. (On large capacity models.)
Ducting Materials:
For best performance, this dryer should be vented with 4” diameter all rigid metal exhaust duct. If “all rigid metal” duct cannot be
used, then “flexible all metal” venting can be used, but it will reduce the maximum recommended duct length.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. The maximum length
for flexible ducts are less than for rigid duct.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45°
should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture and lint from being
blown into the room. Gas dryers or any dryer located in a closet be exhausted to the outside.must
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an
attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a
common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be
located at least 12” above the ground or any other obstruction with the opening pointed Down.
Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a 4” opening dampered wall cap.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0” either side
3” front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed.
If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• The closet should be vented to the outdoors to prevent gas pocketing in case of a gas leak in the supply line.
• No other fuel-burning appliance shall be installed in the same closet with the dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
•Minimum clearances to combustible surfaces
0” both sides
3” rear
0 90 ft. 60 ft. 55 ft. 45 ft.
1 60 ft. 45 ft. 40 ft. 30 ft.
Super & Extra-Large 2 45 ft. 35 ft. 30 ft. 20 ft.
Capacity Models 3 35 ft. 25 ft. 20 ft. 15 ft.
All Electric Dryers 4 25 ft. 15 ft. 15 ft. 10 ft.
0 45 ft. 30 ft. 30 ft. 15 ft.
Super & Extra-Large 1 35 ft. 20 ft. 20 ft. 10 ft.
Capacity Models 2 25 ft. 10 ft. 10 ft. —
All Gas Dryers 3 15 ft. — — —
0 60 ft. 48 ft. 30 ft. 18 ft.
1 52 ft. 40 ft. 22 ft. 14 ft.
Large Capacity 2 44 ft. 32 ft. 14 ft. 10 ft.
Electric and 3 32 ft. 24 ft. — — ft.
Gas Dryers 4 28 ft. 16 ft. — — ft.
Number
of
90°
Turns
Maximum Length of 4"
Dia. DuctRigid Metal
Maximum Length of 4"
Dia. DuctFlexible Metal
Exhaust Hood Type Exhaust Hood Type
Domestic
Dryer Models
Cat. No.
WX8X59
(Preferred)
A
4" Opening
B
2-1/2"
Opening
Cat. No.
WX8X59
(Preferred)
A
4" Opening
B
2-1/2"
Opening
4
Best Performance
B
2-1/2
A
Specication Revised 8/99
NWXR473GVAA—Hotpoint 6.0 Cu. Ft. Extra-Large Capacity Gas Dryer
Features and Benefits
• Extra-Large Capacity (6.0 Cubic Feet)
• Automatic Dry Control
• 7 Cycle Selections: Cottons with Optional Press Guard, Permanent Press with Optional
Press Guard, 80 Minute Timed Dry, Damp Dry, De-Wrinkle
• 4 Heat Selections
• Variable End-of-Cycle Signal
• Up-Front Lint Filter
• Dryer Interior Light
• Double-Coated Drum
• Front Serviceable
• Reversible Door
• Model NWXR473EVWW–White on White (Electric)
• Model NWXR473EVAA–Almond on Almond (Electric)
• Model NWXR473GVWW–White on White (Gas)
• Model NWXR473GVAA–Almond on Almond (Gas)

Specyfikacje produktu

Marka: Hotpoint
Kategoria: Suszarka bębnowa
Model: NWXR473GVAA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint NWXR473GVAA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Suszarka bębnowa Hotpoint

Hotpoint

Hotpoint NWXR483GGWW Instrukcja

14 Stycznia 2025
Hotpoint

Hotpoint NT M11 9X3E IT Instrukcja

29 Grudnia 2024
Hotpoint

Hotpoint NT M11 82XB IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 8X3K IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 9X3SKY IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 82K IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NTS M11 9X3E IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 8X3SKY IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 92WK IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint EU NTDG92 SK IT Instrukcja

11 Grudnia 2024

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Bauknecht

Bauknecht trkk 7846 Instrukcja

15 Stycznia 2025
AEG

AEG T8DEN86CS Instrukcja

15 Stycznia 2025
Candy

Candy GCS 91013A2 Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZDP7204PZ Instrukcja

15 Stycznia 2025
Bauknecht

Bauknecht TRKA Koblenz 4590 Instrukcja

15 Stycznia 2025
Bauknecht

Bauknecht trkk 6840 Instrukcja

15 Stycznia 2025
AEG-Electrolux

AEG-Electrolux Lavatherm 310 Instrukcja

14 Stycznia 2025
Zanussi

Zanussi ZDC82B4SW Instrukcja

14 Stycznia 2025
Bauknecht

Bauknecht trk advance Instrukcja

14 Stycznia 2025
Beko

Beko DCX83120W Instrukcja

14 Stycznia 2025