Instrukcja obsługi Hotpoint FDD 9640P UK

Hotpoint Kombinacje pralko-suszarki FDD 9640P UK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint FDD 9640P UK (16 stron) w kategorii Kombinacje pralko-suszarki. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

! This symbol reminds you to read this instruction

manual.

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Disposal

Description of the washer-dryer, 8-9

Control panel

Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and functions, 9

Table of wash cycles

Wash functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13-14

Product Guarantee and Repair Information, 15

FDD 9640

Instructions for use

English,1

WASHER-DRYER

Installation

ning the adjustable front feet the (see figure);

angle of inclination, measured according to the

worktop, must not exceed 2°.

Levelling your appliance correctly will provide

it with stability and avoid any vibrations, noise

and shifting during operation. If it is placed on

a fitted or loose carpet, adjust the feet in such

a way as to allow enough room for ventilation

beneath the washer-dryer.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see figu-

re).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the other

end of the water inlet

hose to the washer-

dryer, screwing it onto

the appliance’s cold

water inlet, situated

on the top right-hand

side on the rear of the

appliance (see figure).

3. Make sure there are no kinks or bends in the

hose.

! The water pressure at the tap must be within

the values indicated in the Technical details

table (on the page 5).

! If the water inlet hose is not long enough,

contact a specialist store or an authorised

serviceman.

! Ensure that the supply taps are allowing wa-

ter through. Old taps may seize in the closed

position and thus prevent water reaching the

machine.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

! Keep this instruction manual in a safe place

for future reference. Should the appliance be

sold, transferred or moved, make sure the

instruction manual accompanies the washer-

dryer to inform the new owner as to its opera-

tion and features.

! Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

! This is a separate

part of the polystyre-

ne base and should

be removed with the

base.

! IMPORTANT check

when unpacking

your machine.

1. Unpack the washer-dryer.

2. Check whether the washer-dryer has been

damaged during transport. If this is the case,

do not install it and contact your retailer.

3. Remove the 4 pro-

tective screws and

the rubber bush with

the respective spacer,

situated on the rear of

the appliance (see also

the installation leaflet).

4. Seal the gaps using

the plastic plugs provi-

ded.

5. Keep all the parts: you will need them again

if the washer-dryer needs to be moved to ano-

ther location.

! Packaging materials are not children’s toys.

Levelling

Your machine may make a considerable

amount of noise if the two front feet have not

been adjusted correctly.

1. Install the washer-dr-

yer on a flat sturdy floor,

without resting it up

against walls, cabinets

or anything else.

2. If the floor is not per-

fectly level, compensa-

te for any unevenness

by tightening or loose-

Connecting the drain hose

Connect the drain

hose, without ben-

ding it, to a draining

duct or a wall drain

situated between 65

and 100 cm from the

floor;

The drain hose may

be connected to

an under-sink trap.

Before connecting

the drain hose from

the machine ensure

that any blanks or

removable ends have

been taken off the

spigot.

If it is placed over

the edge of a basin

or sink be sure the

free end of the hose

should not be under-

water.

! We advise against the use of hose extensions;

in case of absolute need, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into

a standpipe, that the end does not go down

more than 15cms (6 inches). If the hose is pu-

shed down too far, this may cause the machine

to self -syphon ie. continuously empty as it is

filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Tech-

nical Data Plate fixed on the machine;

• the supply voltage is included within the

values indicated on the Technical Data Plate

fixed on the machine.

• the socket is compatible with the washer-

dryer’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD

BE CARRIED OUT BY A QUALIFIED ELECTRI-

CIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be

of the correct colour as indicated by the colou-

red marking or the colour that is embossed in

words on the base of the plug. Replacements

can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moul-

ded plug and you should wish to re-route the

mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of ap-

proval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Instructions for connecting cable to an alternati-

ve plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Specyfikacje produktu

Marka:	Hotpoint
Kategoria:	Kombinacje pralko-suszarki
Model:	FDD 9640P UK

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint FDD 9640P UK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kombinacje pralko-suszarki Hotpoint

Hotpoint AQD1072D 697 EU/B N Instrukcja

10 Października 2024

Hotpoint FDEU 8640 P UK Instrukcja

8 Sierpnia 2024

Hotpoint RD 966 JD UK Instrukcja

5 Lipca 2024

Hotpoint FDD 9640P UK Instrukcja

5 Lipca 2024

Hotpoint BI WDHG 861484 UK Instrukcja

4 Lipca 2024

Hotpoint BHWDD 74 (UK) Instrukcja

4 Lipca 2024

Hotpoint WDD 750P UK Instrukcja

4 Lipca 2024

Hotpoint FDF 9640 K UK Instrukcja

4 Lipca 2024

Instrukcje Kombinacje pralko-suszarki

Najnowsze instrukcje dla Kombinacje pralko-suszarki

Indesit IWDC 6143 (UK) Instrukcja

14 Października 2024

Summit SPWD2200W Instrukcja

13 Października 2024

Bosch WVD24520EU Instrukcja

13 Października 2024

Indesit WIDXL 146 (UK) Instrukcja

12 Października 2024

Indesit WIDXE 146 S (UK) Instrukcja

12 Października 2024

Indesit EWDC 7145 S FR Instrukcja

12 Października 2024

Indesit PWDE 8148 S (UK) Instrukcja

11 Października 2024

Bauknecht B8 D94WB DE Instrukcja

11 Października 2024

Sanyo SW-160TP Instrukcja

10 Października 2024

Whirlpool FWDG 971682 WBV EE N Instrukcja

8 Października 2024