Instrukcja obsługi Hotpoint ARMXXF 149

Hotpoint Suszarka bębnowa ARMXXF 149

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint ARMXXF 149 (60 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/60
GB
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washer-dryer and
starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the drying cycle
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
GB
ARMXXF 149
Instructions for use
WASHER-DRYER
Polski,37
PL
Nederlands,25
NL
Français,13
FR
Deutsch,49
DE
This symbol reminds you to read this instruction manual.
2
GB
Installation
This instruction manual should be kept in a safe
place for future reference. If the washer-dryer is sold,
transferred or moved, make sure that the instruction
manual remains with the machine so that the new
owner is able to familiarise himself/herself with its
operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its packaging.
2. Make sure that the washer-dryer has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washer-dryer needs to be moved to
another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washer-dryer.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washer-dryer by
screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Technical data
Model ARMXXF 149
Dimensions
width 59,5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 7 kg for the wash
programme;
from 1 to 5 kg for the drying
programme
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed up to 1400 rotations per minute
Energy rated
programmes
according to
regulation
EN 50229
Wash: programme 6; temperature
60°C; using a load of 7 kg.
Drying: first drying cycle perf ormed
with a 2 kg load, by selecting the
dryness level ;
the second drying cycle is performed
with a 5 kg load, by selecting the
dryness level .
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
su bsequent modifications
- 2002/96/EC
- 2006/95/EC (Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washer-dryer. If this is not the case, replace the
socket or the plug.
The washer-dryer must not be installed outdoors,
even in covered areas. It is extremely dangerous to
leave the appliance exposed to rain, storms and other
weather conditions.
When the washer-dryer has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 1.

Specyfikacje produktu

Marka: Hotpoint
Kategoria: Suszarka bębnowa
Model: ARMXXF 149

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint ARMXXF 149, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Suszarka bębnowa Hotpoint

Hotpoint

Hotpoint NWXR483GGWW Instrukcja

14 Stycznia 2025
Hotpoint

Hotpoint NT M11 9X3E IT Instrukcja

29 Grudnia 2024
Hotpoint

Hotpoint NT M11 82XB IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 8X3K IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 9X3SKY IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 82K IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NTS M11 9X3E IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 8X3SKY IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 92WK IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint EU NTDG92 SK IT Instrukcja

11 Grudnia 2024

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Whirlpool

Whirlpool AWZ 7777 Instrukcja

14 Marca 2025
Profilo

Profilo KM9611CTR Instrukcja

13 Marca 2025
Bosch

Bosch WQG241001 Instrukcja

13 Marca 2025
Castor

Castor CCD 230RE Instrukcja

13 Marca 2025
Whirlpool

Whirlpool awz 9816 Instrukcja

13 Marca 2025
Creda

Creda 5 KG Instrukcja

12 Marca 2025
Bauknecht

Bauknecht trkk 7846 Instrukcja

15 Stycznia 2025
AEG

AEG T8DEN86CS Instrukcja

15 Stycznia 2025
Candy

Candy GCS 91013A2 Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZDP7204PZ Instrukcja

15 Stycznia 2025