Instrukcja obsługi Hotpoint AQM8D 69 I V

Hotpoint Suszarka bębnowa AQM8D 69 I V

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint AQM8D 69 I V (16 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
EN
1
English,1
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Description of the machine, 6-7
Touch control panel
How to run a wash cycle or a drying cycle, 8
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent
Preparing the laundry
Washing recommendations
Load balancing system
Precautions and advice, 11
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 12
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Trouble shooting, 13
Assistance, 14
EN
WASHER-DRYER
AQUALTIS
AQM8D 69 I
Instructions for
installation and use
EN
2
Installation
This instruction manual should be kept in a safe place
for future reference. If the washer dryer is sold, given
away or moved, please ensure the manual is kept with
the machine, so that the new owner may benefit from
the advice contained within it.
Read these instructions carefully: they contain vital
information relating to the safe installation and operation
of the appliance.
Inside the pack containing this manual, you will also
find the guarantee and all the details necessary for
installation.
Unpacking and levelling
Unpacking
1. Once you have removed all the packaging from the
washer dryer, make sure it has not been damaged
during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Remove the 4
protective screws (used
during transportation) and
the corresponding spacer,
located on the rear part of
the appliance (see figure).
3. Close off the holes using the plastic plugs supplied in
the pack.
4. Keep all the parts in a safe place; they will be needed
again if the washer dryer is moved to another location,
to prevent the inside of the appliance being damaged.
Packaging materials should not be used as toys for
children.
Levelling
1. Place the washer dryer on a flat sturdy floor, without
resting it up against walls or cabinets.
2. If the floor is uneven,
the front feet of the
machine may be adjusted
until it reaches a horizontal
position (the angle of
inclination must not
exceed 2 degrees).
If the appliance is levelled correctly, it will be more
stable and much less likely to cause vibrations and noise
while it is operating, particularly during the spin cycle.
If it is placed on carpet or a rug, adjust the feet in such
a way as to allow a sufficient ventilation space
underneath the washer dryer.
Connecting the electricity and water
supplies
Connecting the water inlet hose
Before connecting the inlet hose to the water supply,
run the water until it is perfectly clear.
1. Connect the inlet hose
to the machine by
screwing it onto the cold
water inlet of the
appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
2. Connect the inlet hose
by screwing it to a cold
water tab using a 3/4 gas
threaded connection (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical data table (see next
page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand or old inlet hoses; use the
products supplied with the machine.
EN
3
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from the
floor;
The drain hose may be
connected to an under-
sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends have
been taken off the
spigot.
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more than
15cms (6 inches). If the hose is pushed down too far,
this may cause the machine to self -syphon ie.
continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical details
table (see page 5);
the supply voltage is included within the values i
ndicated on the Technical details table (see page 5);
the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused plug
it can be plugged into a 13 amp socket for immediate
use. Before using the appliance please read the
instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse
cover re-fitted. If the fuse cover is lost, the plug must not
be used until a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or
the colour that is embossed in words on the base of the
plug. Replacements can be obtained directly from your
nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug and
you should wish to re-route the mains cable through
partitions, units etc., please ensure that either:
the plug is replaced by a fused 13 ampere re-wearable
plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally
inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap

Specyfikacje produktu

Marka: Hotpoint
Kategoria: Suszarka bębnowa
Model: AQM8D 69 I V

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint AQM8D 69 I V, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Suszarka bębnowa Hotpoint

Hotpoint

Hotpoint NWXR483GGWW Instrukcja

14 Stycznia 2025
Hotpoint

Hotpoint NT M11 9X3E IT Instrukcja

29 Grudnia 2024
Hotpoint

Hotpoint NT M11 82XB IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 8X3K IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 9X3SKY IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 82K IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NTS M11 9X3E IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 8X3SKY IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint NT M11 92WK IT Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint EU NTDG92 SK IT Instrukcja

11 Grudnia 2024

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Whirlpool

Whirlpool AWZ 7777 Instrukcja

14 Marca 2025
Profilo

Profilo KM9611CTR Instrukcja

13 Marca 2025
Bosch

Bosch WQG241001 Instrukcja

13 Marca 2025
Castor

Castor CCD 230RE Instrukcja

13 Marca 2025
Whirlpool

Whirlpool awz 9816 Instrukcja

13 Marca 2025
Creda

Creda 5 KG Instrukcja

12 Marca 2025
AEG

AEG TR718AK2B Instrukcja

10 Marca 2025
AEG

AEG TR968B4C Instrukcja

10 Marca 2025
Bauknecht

Bauknecht trkk 7846 Instrukcja

15 Stycznia 2025
AEG

AEG T8DEN86CS Instrukcja

15 Stycznia 2025